Acer Aspire 2000 Service Guide

							Chapter 245
Others
The Others screen contains various parameter settings.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
ParameterDescriptionOptions
Low Battery Alarm Determines whether or not the system will 
alarm when the battery power is low.Enabled or Disabled
Panel Close Alarm Determines whether or not the system will 
alarm when the display cover is closed.Enabled or Disabled
System Beep Determines whether or not the system will 
emit a beep on boot up.Disabled or Enabled 
						

							46Chapter 2
Boot
The Boot screen allows you to set the order in which the system looks for bootable devices on startup.
The table below describes these devices.
NOTE:  A plus (+) sign may be shown in front of a device. You can press e to “expand” the device and see 
sub-items in this category.
ParameterDescription
Removable Devices The computer attempts to boot from the removable device (e.g., floppy drive). If 
unsuccessful, the system goes to the next device in the list. The removable 
devices include the diskette drive in module bay, the onboard hard disk drive 
and the CD-ROM in module bay..
Hard Drive The computer attempts to boot from the hard disk. If unsuccessful, the system 
goes to the next device in the list.
CD-ROM/DVD Drive The computer attempts to boot from the CD or DVD drive (looks for a bootable 
CD or DVD.)
Network Boot The computer attemptes to boot from LAN. 
						

							Chapter 247
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Saves changes made and exits the BIOS Setup Utility (same as u ).
Exit Discarding 
ChangesDiscards changes made and exits the BIOS Setup Utility.
Load Setup Defaults Loads default settings for all parameters (same as t ).
Discard Changes Discards changes made.
Save Changes Save changes made. 
						

							48Chapter 2
BIOS Phlash Utility
The BIOS flash memory update is required for the following conditions:
!New versions of system programs
!New features or options
!Restore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette 
before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not 
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not 
completely loaded. 
Fellow the steps below to run the Phlash.
1.Prepare a bootable diskette.
2.Copy the Phlash utilities to the bootable diskette.
3.Then boot the system from the bootable diskette. The Phlash utility has auto-execution function.
System Diagnostic Diskette
IMPORTANT: 1The diagnostics program we use for Aspire 1400 is not exactly the same as PQA (Product 
Quality Assurance), the diagnostic program we used to employ in other model. The system 
diagnostic utilities is provided by Acer Headquarters. You can utilize it as a basic diagnostic tool. To 
get this program, find it in the Aspire 1400 service CD kit. To better fit local service requirements, your 
regional office MAY have other diagnostic program. Please contact your regional offices or the 
responsible personnel/channel to provide you with further technical details.
NOTE: For ASSY Function Test Procedure, please prepare the following items for system components test: 
PIO loopback, formatted floppy diskette, CD-DISK (Test Program), Sycard (Card Bus)x2, AC-adapter, 
feather (to see if the fan works), TPDL server, USB_HUP, USB_barcode scanner.
1New added description. Please pay attention to it. 
						

							Chapter 249
Running Diagnostic Program
1.Test program download
Insert TPDL server LAN cable to Aspire 1400 RJ-45 Jack and power on the system via network boot. 
Download the ASSY/PACK test program image. If you see the message below display on the screen, then the 
image download is complete. 
2.Parallel Port Test
Insert PIO loopback to parallel port, then run “PIO.exe” for testing.
3.RTC, FDD Test
Insert diskette to floppy disk drive, then run “Compalt.exe” for t test.
.
4.Configuration check for each SKU 
						

							50Chapter 2
Run “ACR10CFG.bat”. You will see the display below. Then insert USB_Barcode scannner to input the SKU 
part number in oder to check each SKU configuration. .
If the configuration check has no problem, it will go to next test item. If the configuration check fails, the test 
program will pause and show the error configuration.
5.Touch pad/USB Mouse Test
Run “FATMOUSE.exe” to check the touch pad function. Then plug in USB mouse to check its functions. Move 
the cursor to X=0, Y=0 and click left and right buttons as the test is complete. The test program will go to next 
item.
.
6.Video mode Test (LCD/CRT swithc)
Run “SS_PIXS.exe and check the R.G.B video mode display quality on LCD and CRT.” 
						

							Chapter 251
7.Direct Button Test
Run the “BUTTON.exe” to test Audio DJ controls. 
						

							52Chapter 2
8.FAN ON/OFF Test
Run the“TEST42.exe”. You may put a feather in front the fan to see if the fan works or not.
9.CD-ROM and Audio Test
Insert test CD to CD-ROM drive. Then run “Compalt.exe” to check CD-ROM function. If you hear sounds from 
left/right speakers, press “p” to next item.
If you hear sounds from left/right speakers, then press “P” to pass this test item. 
						

							Chapter 253
10.Keyboard Test
Run “KEY38N2.exe”. Press all keys according to this order--from left to right and from up to down to test each 
key’s function. If the test is pass then press b + Break to continue next test.
11 .Caps/Scroll/Number Lock LED Indicator Test
Press keyboard Caps Lock/Num Lk/Fn+Scroll Lk to check LED indicator.
12.Syscard Test (Carbus 32bit)
Insert two pieces of Syscard (Card bus) into PCMCIA slots then run “TESTCB.exe” for testing. 
						

							54Chapter 2
13.Battery Charge Test
Insert AC adapter to the sytem, then run “591NEW2.exe” for testing.