Acer Aspire 1710 Service Guide

Chapter 362
4.Remove the two screws that secure the touch pad. 
5.Remove the touch pad bracket. 
6.Remove the touch pad. 
Remove the touch pad board
1.Remove the four screws that secure the touch pad board.
2.Remove the touch pad board. 
Remove the lid switch cable
1.Disconnect the lid switch cable by releasing the screw.
2.Remove the lid switch cable. 
Remove the floppy drive
1.Disconnect the floppy cable 
2.Remove the three screws 

63Aspire 1710
3.Remove the floppy drive. 
Remove the speaker set
1.Remove the tape 
2.Remove the aluminum tape (the tape can be damaged while servicing, please make sure you have a 
spare one).
3.Remove the tape here.
4.Disconnect the speaker cable. 
5.Remove the screw as shown here.
6.And the one on the other side. 
7.Remove the speaker set.  

Chapter 364
Remove the mainboard
1.Remove the nine screws as shown 
2.Detach the mainboard module from the base unit
3.Remove the screw as shown 
4.Remove the PCI board. 
5.Remove the six screws that secure the I/O shield. 
6.Remove the I/O shield.   
7.Disconnect the system fan power connector. 
8.Remove the two screws, one on each side, that secure the mainboard. 
9.Remove the mainboard from the mainboard bracket. 
Remove the system fan
1.Remove the two screws that secure the system fan.  

65Aspire 1710
2.Remove the system fan.
3.This completes the disassembly procedures of Aspire 1710.
FDD Module
1.Disconnect the ribbon cable. 
2.Remove the screws as shown here. 
3.Remove the FDD bracket away from the floppy drive. 

Chapter 366
HDD Module
1.Disconnect the HDD power cable and then the IDE coaxial cable.
2.Remove the screws that secure the HDD, and the other side.
3.Remove the bracket from the HDD.
Combo Module
1.Remove the three screws as shown here. 
2.Remove the bracket. 

67Aspire 1710 

Chapter 468
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or 
modified options can give false errors and invalid system responses.
1.Obtain the failing symptoms in as much detail as possible.
2.Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating 
the same operation.
3.Use the following table with the verified symptom to determine...

69Aspire 1710
System Check Procedures
External Diskette D rive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is 
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause 
damage to the drive or cause the drive to fail. 
Do the following to select the test device.
1.Boot from the diagnostics diskette and start the diagnostics program.
2.See if FDD Test is passed as the...

Chapter 470
If any of these devices do not work, reconnect the cable connector and repeat the failing operation. 
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.Go to the diagnostic memory in the test items.
3.Press F2 in the test items.
4.Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into...

71Aspire 1710
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power 
adapter cable. See the following figure
1.If the voltage is not correct, replace the power adapter.
2.If the voltage is within the range, do the following:
TReplace the System board.
TIf the problem is not corrected, see “Undetermined Problems” on page 81.
TIf the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not...