Acer Aspire 1410 Service Guide

51Chapter 3
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.Turn off the power to the system and all peripherals.
2.Unplug the AC adapter and all power and signal cables from the system.
3.Remove the battery pack.
NOTE:  The screws used to secure bottom case and upper case are more than one type. Please group same 
type of screw together as you disassemble the system for service purpose. The image below is for your 
reference....

Chapter 352
Screw TypeLocationQuantity
M2.5*6 Bottom case and IO bezel 
(hightlight with yellow circle)14
M2.5*6 Remove the IO bezel then 
you will see.2
M2.5*6 Remove the heatsink cover 
then you will see.1
M2.5*6 Remove the HDD cover then 
you will see.1
M2.5*3 Detach the HDD module  
then you will see.1
M2.5*3 Remove the battery then you 
will see.1 

53Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence 
and instructs you on the components that need to be removed during servicing. For example, if you want to 
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in 
that order.
Start
Battery
HDD CoverODD ModuleRAM/Wireless
CoverE*2
K*2
HDD ModuleWireless LAN
CardMemory
IO Bezel*2
*2
Heatsink
Cover
*2...

Chapter 354
 
Screw List
ItemDescription
SCREW M2.0X3.0-I-NI-
NYLOK 86.A03V7.012
SCREW I2.5*3M-
BNIH(M2.5L3)86.T25V7.012
SCREW M2.5*4L-BZN-
NYLOK 86.A03V7.006
SCREW M2.0X5-I-NI-
NYLOK 
86.T23V7.006
SCREW MM25060IL69
86.A08V7.004
SCREW M2.0*5-
I(NI)(NYLOK)
86.T23V7.010
SCREW M2.0X2.5-I-NI-
NYLOK 
86.A03V7.007
SCREW I2*3M-NIHY 
(M2L3) 
86.T25V7.008
SCREW M1.7*3.0-I 
(BK)
86.T50V7.001
SCREW I3*3.5M-
NIH(M3L3.5)86.A03V7.011
4 screw pads
M*4
LCD Bezel
*6 hinges
*2 brackets
LCD Inverter
LCD
AssemblyLCD Cover...

55Chapter 3
Removing the Battery Pack
1.Unlock the battery lock.
2.Slide the battery latch as shown then remove the battery pack.
  

Chapter 356
Removing the HDD Module/the Memory and the Wireless LAN Card/
the Thermal Module and the CPU/ODD Module and LCD Module
Removing the HDD Module
1.Remove the two screws holding the HDD cover.
2.Remove the HDD cover.
3.Detach the HDD module then remove it.
Removing the Memory and the Wireless LAN Card
1.Remove the two screws that secure the RAM/Wireless cover.
2.Remove the RAM/Wireless cover.
3.Pop up the memory then remove it.
4.Disconnect the auxiliary and the main wireless antennae.
5.Pop the...

57Chapter 3
2.Then remove the IO bezel.
3.Remove the two screws that secure the heatsink cover.
4.Remove the heatsink cover from the main unit.
5.Disconnect the fan cable.
6.Remove the four screws that secure the thermal module.
7.Pull the thermal module outwards then remove it.
NOTE: The edge of the thermal module as shown is very sharp. Be very careful as you remove the thermal 
module.
8.Use a flat-bladed screwdriver to release the CPU lock.
9.Remove the CPU from the socket carefully. 

Chapter 358
Removing the ODD Module
1.Release the ODD latch.
2.Remove the ODD module from the main unit.
.
Removing the LCD Module
1.Remove the three screws holding the keyboard cover.
2.Open the LCD module as the picture shown then detach the keyboard cover from the main unit.
.
3.Remove the two screws that secure the keyboard as shown.
4.Turn over the keyboard as shown and disconnect the keyboard cable then remove the keyboard.
5.Pull out the antenna set with a tweezers then take out the antenna set...

59Chapter 3
8.Then detach the LCD module from the main unit.
. 

Chapter 360
Disassembling the Main Unit
Separate the Main Unit Into the Upper and the Lower Case Assembly
1.Remove the two screws holding the switch board.
2.Remove the switch board.
3.Disconnect the touchpad FFC from the main board.
4.Disconnect the bluetooth cable.
5.Remove the five screws that secure the upper case.
6.Remove the eighteen screws on the bottom as shown.
7.Detach the upper case assembly and place it next to the lower case assembly.
8.Disconnect the microphone cable then remove the upper...