Acco Nobo Digital DLP Projector X17E User Manual

11
... English
Powering On the Projector
1.  Remove the lens cap. 
2.  Ensure that the power cord and signal cable are securely 
connected.  The Power LED will flash green.
3.  Turn on the lamp by pressing “Power/Standby” button on 
the control panel.  The Power LED will turn green.
The first time you use the projector, you can select your 
preferred language from the quick menu after the startup 
screen display.
4.  Turn on your source (computer, notebook, video player,etc.).  
The projector will detect...

12
English ...
Installation
Warning Indicator
  When the “LAMP” indicator lights solid red, the projector 
will automatically shut itself down. Please contact your local 
reseller or service center (refer to pages 33~34). 
  When the “TEMP” indicator lights solid red for about 60 
seconds, it indicates the projector has overheated. The 
projector will automatically shut itself down.
  Under normal conditions, the projector can be switched on 
again after it has cooled down.  If the problem persists, you...

1
2
3
3
13
... English
Installation
Adjusting the Projected Image
Adjusting the Projector Image Height
Tilt Adjusting 
Feet Elevator Foot
23
Elevator Button
The projector is equipped with an elevator foot for adjusting the 
image height.
  To raise the image:
1.  Press the elevator button 
.
2.  Raise the image to the desired height angle  , then release  
  the button to lock the elevator foot into position.
3.  Use   to fine-tune the display angle. 
  To lower the image:
1.  Press the elevator button....

14
English ...
Installation
69.3"
(176.1cm)115.6"
(293.5cm)161.8"
(410.9cm)184.9"
(469.6cm)277.3"
(704.4cm)
38.1"
(96.8cm)76.2"
(193.6cm)127.1"
(322.7cm)177.9"
(451.8cm)203.3"
(516.3cm)304.9"
(774.5cm)
4.9'
39.4' 26.3' 23.0' 16.4'9.8'(1.5m)
(12.0m) (8.0m) (7.0m) (5.0m) (3.0m)34.7"
(88.1cm)
Max.38.1"(96.8cm)76.2"(193.6cm)127.1"(322.7cm)177.9"(451.8cm)203.3"(516.3cm)304.9"(774.5cm)
Min. 34.7"(88.1cm)...

15
... English
User Controls
Remote Control Control Panel
Control Panel & Remote Control
There are two ways for you to control projector functions: 
Remote Control and Control Panel.
  Using the Control Panel
 Power/Standby  
Refer to the “Power On/Off the Projector” section on pages
   11-12.
Source
Press “Source” to choose RGB, Component-p, Component-i,
    S-Video, Composite Video and HDTV sources.
Menu
Press “Menu” to launch the on-screen display (OSD) menu.
    To exit OSD, press “Menu” again....

16
English ...
User Controls
  Using the Remote Control
 Power  
Refer to the “Power On/Off the Projector” section on pages 11-12.  
 Re-Sync
Automatically synchronises the projector to the input source.
  Volume + / - (Vol+/Vol-)
Increases/decreases speaker volume.
 Reset
Changes the adjustments and settings to the factory default
   value.
Hide
Press “Hide” to hide image, press again to restore display of the
   image.
 Keystone  / 
Adjusts image distortion caused by tilting the projector (±15...

The Projector has multilingual On Screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.  To open the OSD menu, press “Menu ” on the Remote Control
  or Control Panel.
2.When OSD is displayed, use   keys to select any item in the
  main menu.  While making a selection on a particular page, press  
 or “Enter” key to enter sub menu.
3.Use  keys to select the desired item and adjust the...

Menu Tree
English/Deutsch/Français/Italiano/Español/
Português/Nederlands/Polski
18
English ...
User Controls 

Language
 Language
  Choose the multilingual OSD menu . Use the   or  key to select
  your preferred language. 
  Press “Enter” to finalise the selection. 
19
... English
User Controls
English
Français
Deutsch
Italiano
Español
PolskiPortuguês
Nederlands 

20
English ...
User Controls
Image-I
 Display Mode
There are many factory presets optimised for various types of  
 images.  
   PC: For computer or notebook.
   Movie: For home theater.
Game : For game.
   sRGB: For standard colour.
   User: Memorise user ’s settings.
 Brightness
Adjust the brightness of the image.
Press the 
 to darken the image.
Press the 
 to lighten the image.
 Contrast
The contrast controls the degree of difference between the lightest  
  and darkest parts of the picture....