3M Projector SPR1000 User Manual

							3M™ Streaming Projector SPR1000
© 2012 3M. All Rights Reserved.
 21
English3 Select the outlet adapter that will plug into your wall outlet and align to the power 
adapter.
4 Slide the outlet adapter down until it clicks into place. 
						

							3M™ Streaming Projector SPR1000
 22 © 2012 3M. All Rights Reserved.
English
Charging the Battery
The rechargeable battery in the 3M Streaming Projector SPR1000 gives you up to two 
hours of battery life while in ECO lamp mode. When the battery needs to be charged, 
the status indicator LED starts flashing red. The battery should be fully charged before 
using the projector for the first time. 
Charge the battery:
1 Turn the projector power off. 
2 Connect the power adapter to the projector’s DC input. 
3 Connect the other end of the power adapter to the electrical outlet.
4 The status indicator will change to amber while the battery is charging. 
5 Allow three hours to fully charge the battery. When charging is complete, the 
status indicator will flash green.
Battery Charging Notes:
•	 If the projector power is off, allow three hours for the battery to fully recharge. If 
the projector power is on, the battery will take longer to charge.
•	 The battery has a lifespan and ages every time it is fully charged and discharged. 
The battery will gradually lose charge capacity as it ages.  
						

							3M™ Streaming Projector SPR1000
© 2012 3M. All Rights Reserved.
 23
EnglishBattery Maintenance Tips:
•	 Charge and discharge the battery by turning on the projector at least once a 
month. 
•	 When storing the projector for more than a month, store it at 50% charge.
•	 The battery is at 50% charge when half of the battery icon is white.
•	 Do not store the projector when it is fully discharged. It will lose the ability to 
charge.
Turning the Projector on and off
When you first pull the projector out of the box, you can only use the power button 
on the projector to turn it on . After the projector is turned on for th first time, you can 
turn it on or off using the power button on either the remote or project\
or . 
MHL-enabled devices such as the Roku Streaming stick receive power from the 
projector. You can turn off the projector's lamp without turning off the MHL-enabled 
device using the remote control.
Turning the Projector On:  Press the power button on the projector or remote control. 
Note: Some devices that receive their power from the projector might take 30 
seconds or more to become ready to use. 
Turning the Projector Off:  Press and hold the power button until the projector turns 
of f.  
						

							3M™ Streaming Projector SPR1000
 24 © 2012 3M. All Rights Reserved.
English
Turning the Lamp On and Off: You can turn the projector's lamp off without turning 
the projector off by pressing the lamp button on the remote control. The projector lamp 
will turn off immediately while the cooling fans continue to run. 
While the projector's lamp is off, the status indicator remains green. This tells you that 
the lamp is off but the projector is still on. Press Lamp On/Off button on the remote 
again and the lamp will turn on.
Important Note: Even though the lamp is off, the projector continues to use a 
power and generate heat. The projector will turn off if it overheats or loses battery 
power. You can prevent the projector from turning off by keeping the air vents 
clear and plugging it into the power adapter.
Status Indicator Light
The status indicator light provides information about the projector’s power, battery, and 
error status. 
Status Indicator Light Meaning
Solid amber The projector is charging.
Solid green The projector is on.
Flashing green The projector is finished charging.
Flashing amber The projector has overheated.
Flashing red The battery power is low. 
						

							3M™ Streaming Projector SPR1000
© 2012 3M. All Rights Reserved.
 25
EnglishSetting up the Projector
The projector is quick and easy to set up. You can project the image onto most flat 
surfaces. This section covers positioning the projector, focusing the image, and 
adjusting the brightness and contrast settings. 
Choosing a surface 
The best surface for the image is a flat, white surface. In most cases, lightly textured 
walls do not affect the image quality. Alternatively, a color wall will change the hue of 
the image.  You can either point the projector at a wall or projector screen or a ceiling. 
Placing the projector
Place the projector on a stable surface. You can place the projector on its foot or on 
the rear cover. You can even attach the projector to a tripod. 
						

							3M™ Streaming Projector SPR1000
 26 © 2012 3M. All Rights Reserved.
English
 Attaching the Projector to Tripod (Optional Accessory)
On the bottom of the projector, you will find a tripod socket (1/4"-20) that fits most 
standard camera tripods, including the optional 3M tripod (78-6972-0073-7). 
						

							3M™ Streaming Projector SPR1000
© 2012 3M. All Rights Reserved.
 27
EnglishDistance versus Image Size
The 3M Streaming Projector can project an image from 9 inches (22.1 cm) to 105 
inches (265.7 cm) wide. As you increase the size of the projected image, you will 
need to decrease (darken) the ambient room lighting. Refer to the chart for associated 
dimensions.
Image Size 
Diagonal  
Width  
Height 
Distance
10 in (25.4 cm) 8 3/4 in (22.1 cm) 4 7/8 in (12.4 cm)16 5/8 in (42.2 cm)
20 in (50.8 cm) 17 3/8 in (44.3 cm) 9 3/4 in (24.9 cm)33 1/4 in (84.3 cm)
35 in (88.9 cm) 30 1/2 in (77.5 cm) 17 1/8 in (43.6 cm)58 1/8 in (147.6 cm)
45 in (114.3 cm) 39 1/4 in (99.6 cm) 22 in (56.0 cm)74 3/4 in (189.7 cm)
55 in (139.7 cm) 47 in (121.8 cm) 26 in (68.4 cm)91 1/4 in (231.9 cm)
65 in (165.1 cm) 56 5/8 in (143.9 cm) 31 7/8 in (80.9 cm)107 7/8 in (274.1 cm)
76 in (193.0 cm) 66 1/4 in (168.3 cm) 37 1/4 in (94.6 cm)126 1/8 in (320.4 cm)
85 in (215.9 cm) 74 1/8 in (188.2 cm) 41 5/8 in (105.8 cm)141 1/8 in (358.4 cm)
141 1/8 in (358.4 cm) 82 7/8 in (210.4 cm) 46 1/2 in (118.2 cm)157 3/4 in (400.6 cm)
110 in (279.4 cm) 95 7/8 in (243.6 cm) 53 7/8 in (136.9 cm)182 5/8 in (463.8 cm)
120 in (304.8 cm) 104 5/8 in (265.7 cm) 58 3/4 in (149.3 cm)199 1/4 in (506.0 cm) 
						

							3M™ Streaming Projector SPR1000
 28 © 2012 3M. All Rights Reserved.
English
Adjusting the Focus
After you find a place for the projector, rotate the focus wheel to sharpen the image.
Focus
Adjusting the Brightness and Contrast Settings
You can use the projector brightness and contrast settings to adjust the image based 
on the lighting conditions.
Adjusting the Brightness
Adjust the brightness setting until details in the dark levels of the image appear. If you 
are unable to see the detail, try reducing the image size or the lighting in the room. 
Using the Remote: Press the menu button at the top-right of the remote control; press 
the Ok button; press the right arrow to increase the brightness or the left arrow button 
to decrease the brightness. You can exit the menu by pressing the menu button twice.  
						

							3M™ Streaming Projector SPR1000
© 2012 3M. All Rights Reserved.
 29
EnglishUsing the Projector Keypad:  Press the menu button; press the Info button; press the 
volume down to decrease the brightness and volume up to increase the brightness. 
You can exit the menu by pressing the menu button twice.
Adjusting Contrast
Adjust the contrast setting until details in the bright level of the image appear.
Using the Remote:  Press the menu button at the top-right of the remote control; press 
the down arrow; press the Ok button; press the right arrow to increase the contrast 
brightness or the left arrow button to decrease the contrast. You can exit the menu by 
pressing the menu button twice.
Using the Projector Keypad:  Press the menu button; press the Info button; press the 
volume down to decrease the brightness and volume up to increase the brightness. 
You can exit the menu by pressing the menu button twice. 
						

							3M™ Streaming Projector SPR1000
 30 © 2012 3M. All Rights Reserved.
English
Volume Up/Down
The volume buttons on the projector and the remote control adjust the sound from 
the speakers or the audio output. Additionally, MHL enabled devices plugged into the 
projector can adjust the projector volume level using the device's remote. 
Display Volume Level: Press the volume up or down button to display the volume 
slider.
Increase or Decrease Volume: Press the volume up button to increase the audio 
volume or press the volume down button to decrease the audio volume.
Quickly Increase or Decrease Volume:  Press and hold the volume up button to quickly 
increase the audio volume or press and hold the volume down to quickly decrease or 
mute the audio volume.
Mute the Sound:  Press the volume up and down on the projector at the same time or 
press the mute button on the remote control.