3M Multimedia Projector X62 Operators Manual

							
3M™ Multimedia Projector X62 Product Safety Guide© 3M 200611

CAUTION
•    To reduce the risk associated with explosion, and/or chemicals from a leaking battery:
  -   Use only with battery type AA or equivalent.
  -   � rient the battery �s plus  ���� and minus  �-�� terminals of the batteries according to 
the markings found on the remote control.
  -   Do not leave the battery in the remote for an extended period of time.
	 - 		 Do 	not 	heat ��	disassem �le ��	short ��	rechar �e��	or 	e �pose 	to 	fire 	or 	hi �h	temperat �re �
  -   Do not carry batteries loose in your pocket or purse.
  -   Avoid eye and skin contact in the event that battery would leak.
  -   Do not mix used and new batteries.
•  To reduce the risk associated with intense visible light:
  -   Avoid looking directly into the projector lens while the lamp is on.
ENGLISH
•  To reduce the risk associated with exposure to hazardous voltage:
  -   Disconnect power cord when the projector is not in use, during lamp replacement, 
and while cleaning.
  -  Do 	not 	remove 	any 	screws 	other 	than 	those 	specified 	in 	the 	lamp 	replacement 	instr �ctions �
 -   Do not attempt to service the projector - there are no user serviceable parts, other 
than the lamp cartridge, inside the projector. Contact a 3M authorized service 
provider for service.
•  To reduce the risk associated with hot surface of lamp cartridge:
  -   Unplug the projector from the electrical outlet and allow the lamp to cool for   
minutes before replacing the lamp.
•  To reduce the risk associated with a ruptured lamp:
  -   Always handle the fragile lamp module with care.
  -   Remove the projector from the ceiling or wall mount before replacing the lamp. In 
the case of a lamp rupture, small glass particles could fall out when the lamp door 
is opened or the projector is tilted.
  -   Use care when replacing the lamp module in the event of a lamp rupture - small 
glass particles and small amounts of mercury may be present.
  -   Ventilate the area where the lamp rupture occurred.
  -   Wear safety goggles and gloves when cleaning up ruptured lamp debris.
  -  Carefully collect the ruptured lamp debris in a closed container and dispose of the container 
and the expired lamp module in accordance with federal, state, and local regulations.
  -   Wash your hands thoroughly after handling ruptured lamp debris.
  -   Replace the lamp module when the lamp replacement message appears.
  -   Never replace the lamp module with a previously used lamp module.
• To reduce the risk associated with environmental contamination due to mercury:
  -  Dispose of lamp cartridge in accordance with applicable federal, state and local regulations.
WARNING
The glass lamp used in this projector contains small amounts of mercury and operates athigh pressure and at high temperature and may unexpectedly shatter. Each lamp has adifferent lifetime and can fail in different ways, including a rupture with a loud bang orsimply burn out. In the event of a lamp rupture, be sure to follow the instructions.
Replacing Lamp
Important Note:
���	 the 	lamp 	�rea �s	soon 	a ��ter 	the 	first 	time 	it 	is 	� sed ��	it	is 	possi �le 	that 	there 	are 	electrical 	pro �lems 	elsewhere besides the lamp. If this happens, contact your local dealer or a service representative. 
						

							
3M™ Multimedia Projector X62 Product Safety Guide© 3M 200612

ENGLISH
√		Note
Reset the lamp operation hours. See “Reset Lamp Hours” for details\
.
3.  Remove lamp module: Slowly pick up the lamp module by the handles. (4)4.  Insert lamp module: Carefully insert (4) the new lamp module. Ensure that it is fully seated. Tighten the lamp module retaining screws (3) to secure the lamp module in place.  Optional Lamp: 78-6969-9875-2 (Contact 3M Customer Service.) Slide the lamp door (2) back in place and firmly fasten the lamp door a screw . (1)
√		Note
For maximum lamp life, do not strike or drop, improperly handle, or scratch the lamp glass. Also, do not install an old or previously used lamp.
1.  Remove lamp access door: Loosen the lamp door screw (marked by arrow) (1) and then slide the lamp door to the side to remove it. (2)2.  Retaining screws: Use a screwdriver to unscrew the lamp module retaining screws (marked by arrow). (3)
√		Note
All lamp module screws must be loosened. These screws are self-containing screws that cannot be removed from the lamp module or access door.
�2�� Lamp access door
�1�� Screw��� Handle
�3�� Screws  
						

							
3M™ Multimedia Projector X62 Product Safety Guide© 3M 200613

Warranty
LIMITED WARRANTY
This product will be free from defects in material and manufacture for a\
 period of three (3) years from the date of purchase, subject to the following limitations. The following are exclusions to the above listed warranty or are subject\
 to a different warranty as set forth below:(a) The warranty for lamps that are included as original equipment in the projectors is for parts only and is effective for a period of 90 days after the date of purchase of the projector or 180 hours of lamp usage,whichever occurs first.(b) The warranty period for LCD panels (including polarizers) is either 3 \
years from the date of purchase of the projector or 2500 hours of projector usage,whichever occurs first.If within 3 years from the date of purchase of the projector,the LCD panel requires replacement and is otherwise eligible for warranty coverage,but\
 the projector has exceeded 2500 hours of usage, the 3M warranty will cover the cost of labor,but not the cost of parts that require replacement.(c) 3M Digital Projectors are designed to operate in a typical indoor \
environment. Product Warranty is void if used outside of the following circumstances: • 100V –240V AC,50/60 Hz • 16 °to 29 °C (60 °to 85 °F) • 10 –80%RH (without condensation) • 0 –1828m (0 –6000 feet) above sea level • The ambient operating environment should be free of airborne smoke, grea\
se, oil and other contaminates that can effect the operation or performance of the projector.(d) The warranty will be void if you repair or modify the 3M Digital Project\
or or you otherwise damaged the product due to misuse, neglect, mishandling or other abuse.
LIMITATION OF LIABILITY
THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M  SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITY AND FITNESS. 3M SHALL NOT BE  LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUENTIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT.
Important: The above warranty shall be void if the customer fails to operate produc\
t in accordance with 3M’s written instructions. This warranty gives you specific legal rights and you may have other rights which vary from state to state.
FCC STATEMENT - CLASS B: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual may cause interference to radio communications. It has been tested and found to comply with the limits for a Class “B” computing device pursuant to Subpart B of Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference when operated in a residential installation.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:* Reorient or relocate the receiving antenna.* Increase the separation between the equipment and receiver.* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.* Consult the dealer or an experienced radio/TV technician for help.INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC equipment provided that the following conditions are met. The cables may have to be used with the core set to the projector side. Use the cables which are included with the projector or specified.Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.
Video Signal Cables: Double shielded coaxial cables (FCC shield cable) must be used and the outer shield must be connected to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation.
Video Inputs: The input signal amplitude must not exceed the specified level.
PATENTS, TRADEMARKS & COPY RIGHTS
IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook are registered trademarks of Apple Computer, Inc. Microsoft and Windows 95 & Windows 98 are registered trademarks, and Windows and Windows for Workgroups are trademarks of the Microsoft Corporation. Toshiba is a registered trademark of Toshiba Corporation. Kensington is a trademark of Kensington Corporation. All other products are trademarks or registered trademarks of their respective companies.
ENGLISH 
						

							
3M Austin CenterBuilding A145-5N-016801 River Place Blvd.Austin, TX 78726-9000
3M CanadaP.O. Box 5757London, OntarioN6A 4T1
3M Mexico, S.A. de C.V.Apartado Postal 14-139Mexico, D.F.  07000Mexico
3M EuropeBoulevard de l’Oise95006 Cerge Pontoise CedexFranceLitho in ChinaChina© 3M 2006-690-9- Rev. AQR60316031
Important NoticeAll statements, technical information, and recommendations related to 3M\
’s products are based on information believed to be eliable, but the accuracy or completeness is not guaranteed. Before using this product, y\
ou must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purch\
ase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M."
Let us help you make the most of your next presentation.  We offer everything from presentation supplies to tips for better meetings.  \
And we’re the only transparency manufacturer that offers a recycling program for your used transparencies.  For late-breakin\
g news, handy reference  and free product samples, call us toll-free in the continental United States and \
Canada, 24 hours a day, or visit our Internet Website.