3M Multimedia Projector Mp8760 Operators Manual

							63M Multimedia Projector MP8760 3M IPC 2000
ENGLISH
3-5. Image Size (Projector-to-Screen Distance)
Adjust the size of the projected image using the zoom control buttons. The projected image size values, as they relate
to the distance-to-screen value, are shown for focal lengths of f=25mm and f=45mm. Also shown is the maximum
image height shift value that can vary depending on the focal length and the distance-to-screen.  Figure 3.4.
Maximum (f=25mm) Minimum (f=45mm)
Distance to Screen
m (ft.)Image Width
m (in.)Image Height
m (in.)Max Height
m (in.)Image Width
m (in.)Image Height
m (in.)Max Height
m (in.)
2.00   (6.56) 1.42   (56.0) 1.06   (41.7) 0.43 (16.9) 0.80   (31.5) 0.60   (23.6) 0.24   (9.5)
2.50   (8.20) 1.76   (69.3) 1.32   (52.0) 0.54 (21.3) 0.99   (39.0) 0.74   (29.1) 0.30 (11.8)
3.00   (9.84) 2.11   (83.1) 1.57   (61.8) 0.64 (25.2) 1.18   (46.5) 0.89   (35.0) 0.36 (14.2)
5.00 (16.40) 3.48 (137.0) 2.60 (102.4) 1.06 (41.7) 1.96   (77.2) 1.47   (57.9) 0.60 (23.6)
7.00 (22.97) 4.85 (191.0) 3.62 (142.5) 1.47 (57.9) 2.73 (107.5) 2.05   (80.7) 0.83 (32.7)
10.00 (32.81)   6.90 (271.7) 5.16 (203.2) 2.10 (82.7) 3.88 (152.8) 2.92 (115.0) 1.18 (46.5)
Figure 3.4. Image Size/Maximum Image Height
3-6. Image Height
Use the Picture menu/Height option to shift (upward) the projected image. The center of the projected image can be
shifted a maximum of 12 degrees without incurring any keystoning. Figure 3.5.
Figure 3.5.  Maximum Image Shift
EPS-47A
Zero
Shift Max.
Shift
12 Degree Maximum Shift 
						

							 3M IPC 2000 3M Multimedia Projector MP8760 7
ENGLISH
 Section 4: Operating Instructions
4-1. Power Up Projector
Read the Important Safeguards before operating the MP8760 projector. After all cable connections have been
completed, the projector can be powered up. During operation, keep the exhaust and intake air vents clear of
obstructions to allow proper cooling.
!Caution
Allow a projector that has been stored in a cold place to warm up to room
temperature before applying power.
Figure 4-1. Power Up Projector
1. Press the Main Power switch 
(1) to ON. A red LED indicator will illuminate to indicate there is power.
2. Press the Standby button 
(2) to illuminate the lamp. A red LED indicator will turn green as an image appears
and grows brighter on the screen.
3. Check all ventilation slots 
(3) and clear away all obstructions.
!! ! !
 Note
Ventilation vents are located on the top and back of the projector. Do not
block airflow by placing objects on top of the projector.
4. Adjust the Focus (4) and Zoom (5) for best image.
5. Press the Foot Release button 
(6) to release the height adjustment foot (7).
6. Power up your computer and video source(s).
!! ! !
 Note
In most cases, the projector will automatically adjust to the graphic mode
of your computer by selecting a pre-programmed setting.
ENTERFOCUS ZOOM
PC
MENU VIDEOAUX
++
——
EPS-18A
OI
3 1
5
6
74 2 
						

							83M Multimedia Projector MP8760 3M IPC 2000
ENGLISH
4-2. Standby Mode
When the projector is not being used, place it into standby mode.
1. Press the Standby button.
2. The lamp will switch off and the red LED will illuminate.
!! ! !
 Note
The fan motor will continue to run for a few minutes until the projector
cools down and then the fan will turn off.
3. Press the Standby button again to illuminate the lamp and project an image on the screen.
4-3. Projector Power Down
1. Press the Standby button to place the projector in the standby mode (red LED illuminates).
2. Wait until the cooling fan motor cycles off and the lamp LED turns off.
!! ! !
 Note
Switching the main power off before the fan has cycled off will decrease the life of
the projection lamp.
3. Press the Main Power switch to Off.
4. Turn off the power to your input devices.
5. Install lens cap to protect projection lens.
6. To transport the projector, disconnect all power and connection cables.
4-4. Using System Menus
Main Menu: Press the Menu button on the operator touch panel keypad (Figure 3-3) or the remote control keypad
(Figure 5-1) to display the Main Menu.
The menu name (1) is on the top line.
An arrowhead (2)
 at the right of a menu line indicates
that this item is a sub-menu that can be selected.
A text field (3) at the right of a line indicates that this
is a value that you can change in a drop down
window.
Info:  Press Enter to display the Info window.
To select a sub-menu, press the Disc Pad up or down to highlight (select) the desired sub-menu (2).  Then press the
Disc Pad to the right or the Enter button to display the sub-menu (see Sub-Menu).
To change a text field value, press the Disc Pad up or down to 
highlight (select) the menu line (3).  Then press the
Disc Pad to the right or the Enter button to display a drop down window of all the possible values. Use the Disc Pad
to select a value and press Enter to initiate the selection.
To exit a sub-menu, press the Disc Pad to the left.
To completely exit the menu system and return to the projected image, press the Menu button.
Main Menu
 Picture
 Audio
 Tools                                 
 Signal source         PC/RGB1
 User Interface
 Advanced Setup               
Info
1
3 2 
						

							 3M IPC 2000 3M Multimedia Projector MP8760 9
ENGLISH
Sub-Menu: Select the desired sub-menu (see Main Menu). Press the Disc Pad to the right or the Enter button to
display the sub-menu.
The sub-menu name (1) is on the top line.
A check box field 
 (2) at the right of a sub-menu
line indicates that you can toggle that value On/Off by
pressing the Enter button.
A slider bar (3) at the right of a sub-menu line
indicates you can increase or decrease the value.
A number field (4) at the right of a sub-menu line
indicates that you can change it.
 To change a slider bar value, it must be highlighted.  Press the +/– button on the remote control or Bright +/– button
on the operator touch panel to increase or decrease the value.
To change a number field, press the Disc Pad up or down to highlight (select) the menu line.  Then press the +/–
button on the remote control or Bright +/– button on the operator touch panel to increase or decrease the amount of
the value.
4-5. Menu Adjustments/Settings
The following charts lists all the menu items that can be adjusted along with the default settings.
Main Menu Description / Action Default
Setting
Picture Display picture submenu
Audio Display audio submenu
Tools Display tools submenu
Source
(drop down window)Select input source
(PC/RGB1 / PC/RGB2 / SVHS /
VIDEO 1 / VIDEO 2 / AUX)According
to search
procedure
User Interface Display user interface submenu
Advanced Setup Display advanced setup submenu
Info Display information window
(press Enter)
In active PC/RGB mode:
Picture (PC/RGB)
Submenu ItemsDescription / Action Default
Setting
Height
Adjust projected image height
 
Brightness Adjust the brightness
Contrast Adjust the contrast
Optimize Set best brightness for image
Hor. Position Adjust horizontal position of image
Ver. Position Adjust vertical position of image
Tracking Adjust number of pixels per line
Sync Adjust phase synchronization
Mode Select data mode to adjust within this
menu (Predefined modes /
User Mode 1…3)
Resolution
(drop down window)Select pixel resolution (640x350 /
720x350 / 640x400 / 720x400 /
640x480 / 800x600 / 832x624 /
1024x768 / 1152x864 / 1152x870 /
1152x900 / 1280x960 / 1280x1024)
Main Menu
Picture
Audio
Tools
                                    
Signal source           PC/RGB1
User Interface
Advanced Setup
                 
Info
Picture
Height
                            
Brightness
Contrast
Optimize                                   
Hor. Position
Ver. Position                 
Tracking             1312
Sync                              
Mode VESA 1024 x 768 75Hz
Resolution 1024 x 768
Tools
 Freeze                                   
 Magnify
 Factor                           
 Timer off
Minutes 10
1
2
3
4 
						

							10 3M Multimedia Projector MP8760 3M IPC 2000
ENGLISH4-5.  Menu Adjustments/Settings, continued
In active Video mode:
Picture (Video)
Submenu ItemsDescription / Action Default
Setting
Height
Adjust projected image height 
Brightness Adjust the brightness
Contrast Adjust the contrast
Color Adjust color saturation
Tint Adjust HUE for NTSC
Audio
Submenu ItemsDescription / Action Default
Setting
Volume Adjust volume
Audio Audio mute    -on / -off-on
Speaker Speakers    -on / -off-on
Balance Adjust balance
Treble Adjust treble
Bass Adjust bass
Surround Adjust surround sound level
Tools
Submenu ItemsDescription / Action Default
Setting
Freeze Freeze frame    -on / -off-off
Magnify Magnify mode    -on / -off-off
Factor Adjust magnification factor
Timer Select timer mode (off / small / large) off
Minutes Adjust timer countdown
(1 to 90 minutes)10 minutes
User Interface
Submenu ItemsDescription / Action Default
Setting
Language
(drop down window)Select user interface language
(English / Deutsch / Français /
Español / Italiano / Nederlands /
Svenska)English
Blank Screen Color
(drop down window)Select color of Blank Screen
(Black / Red / Green / Blue / Yellow /
Cyan / Magenta / White)Black
Graphics Activate on-screen status bar
indicators and icons. (e.g. 
)
 
-on /  -off
-on
Reset Window
PositionReset all menu window position to
default
Help
(drop down window)Select Help window mode
(immediate / 1, 3, or 5 seconds / off)3 seconds
Audio
 Volume
 Audio        
 Speaker                                
 Balance
 Treble
 Bass
 Surround
Tools
 Freeze                                   
 Magnify
 Factor                           
 Timer off
Minutes 10
User Interface
 Language English
 Blank Screen Color Black
 Graphics
 Reset Window Position
 Help 3 seconds
Picture
 Height                            
 Brightness
 Contrast
 Color
 Tint  
						

							 3M IPC 2000 3M Multimedia Projector MP8760 11
ENGLISH
4-5.  Menu Adjustments/Settings, continued
In active PC/RGB mode:
Advanced Setup
(PC/RGB)
Submenu ItemsDescription / Action Default
Setting
Projection
(drop down window)Select projection orientation
(standard / Rear / Rear/Ceiling /
Ceiling)standard
Color Manager Display Color Manager submenu
Remote Control Remote control receiver -on / -off-on
RC Address Select remote control address
(1 / 2 / 3 / 4)1
Sync Mode1
(drop down window)Select Sync Mode for PC/RGB1
(separate TTL / composite TTL /
separate ana. / composite ana. /
sync on green)separate TTL
Sync Mode2
(drop down window)Select Sync Mode for PC/RGB2
(separate TTL / composite TTL /
separate ana. / composite ana. /
sync on green)separate TTL
SOG Level Adjust level for sync on green
synchronization
Reset Data Modes Set all data modes to factory default
settings.
Reset lamp display Resets the lamp hours displayed on
the Info window
Test Display test submenu
In active Video mode:
Advanced Setup
(Video)
Submenu ItemsDescription / Action Default
Setting
Projection
(drop down window)Select projection orientation
(standard / Rear / Rear/Ceiling /
Ceiling)standard
Color Manager Display Color Manager submenu
Remote Control Remote control receiver -on / -off-on
RC Address Select remote control address
(1 / 2 / 3 / 4)1
Video standard
(drop down window)Select Video standard
(PAL B,G,H,I /  NTSC M / SECAM /
NTSC 44 / PAL M / PAL N / PAL 60 /
NTSC COMB /  automatic)automatic
Reset lamp display Resets the lamp hours displayed on
the info window
Test Display test submenu
Advanced Setup
Projection standard
Color Manager
Remote Control
RC Address                            1
Video standard         automatic
Reset lamp display                  
Test
Advanced Setup
Projection standard
Color Manager
Remote Control
RC Address                            1
Sync Mode1 separate TTL
Sync Mode2 separate TTL
SOG level                     
Reset Data Modes
Reset lamp display                  
Test 
						

							12 3M Multimedia Projector MP8760 3M IPC 2000
ENGLISH
4-5.  Menu Adjustments/Settings, continued
Color Manager
Submenu ItemsDescription / Action Default
Setting
Brightness red Adjust brightness for red portion
Contrast red Adjust contrast for red portion
Brightness green Adjust brightness for green portion
Contrast green Adjust contrast for green portion
Brightness blue Adjust brightness for blue portion
Contrast blue Adjust contrast for blue portion
Default Sets color settings to default values
Test
Submenu ItemsDescription / Action Default
Setting
Parameter display Parameter display window
-on / -off
-off
Color test picture Display color test picture
Frame test picture Display frame test picture
Info (display only) Description / Action
Hardware Current hardware level
Firmware Current firmware level
VESA xxxxxxxxxx Current data or video mode
Lamp (bar indicator) Lamp life hours (Green: lamp good /
red: lamp needs replacement)
OK! Closes the Info display by pressing
the Enter button
Test
 Parameter display
 Color test picture
 Frame test picture
3M
MP8760
Hardware: xxx-x.xx-x
Firmware: xxx-x.xx
VESA 1024 x 768  75 Hz
                 Lamp
      OK!     
Color Manager
 Brightness red
 Contrast red                  
 Brightness green
 Contrast green              
 Brightness blue
 Contrast blue                
 Default 
						

							 3M IPC 2000 3M Multimedia Projector MP8760 13
ENGLISH
 Section 5: Remote Control
5-1. Remote Control Functions
Aim the remote control toward the projection screen or at the sensor.  Press desired remote button to send a signal to
the projector.
An icon will display to indicate a presentation
tool is active.
Pointer Freeze
imageMouse Mute Magnify
imageReveal
image
! Note
The buttons marked with an asterisk (*) also appear on
the operator touch panel keypad.
ENTER
FOCUS ZOOM
PCMENUVIDEOAUX
123
456
789
0
VOL BRIGHTREVEAL
–+
BLANKDRAG
CH–CH+ TIMER OPTIMIZE TEXT WINDOW
MOUSE
POINTER
MODE
1-2-3-4
INFOMAGNIFYFREEZE
EPS A
LR
*Standby: Switch the projector
between Standby mode (lamp off,
fan off) and operation mode (lamp
on fan on)
*Zoom: Increase (+) or decrease
(-) size of displayed image.
*Menu: Display system menus. *PC: Switch to PC mode.  In PC mode,
toggles between RGB1 & RGB2.
*Focus: Adjust focus (+/-) of
displayed image. *Video: Switch displayed image to
video input. In Video mode , toggles
between: Video1 / Video2 / SVHS
*Bright: Increase (+) or decrease (-)
brightness of displayed image. *Enter: Mouse emulation ON, left mouse
button. Mouse emulation OFF, Enter
button for confirmation of a selection.
*Mute: Toggle On/Off the audio sound. *Volume: Increase (+) or decrease (–)
speaker volume.Disc Pad (mouse pointer): Move
(point) the cursor on the projected
image. Navigate menus.  See Pointer.
Window: Toggle between full
screen and centered display mode
(Non-XGA modes only!!!)
Mode 1,2,3,4: Toggle between remote control
addresses 1, 2, 3, 4. (See Appendix ?) Drag: Lock left mouse button.
Optimize: Adjust brightness and
contrast for best picture.
Reveal: Press Reveal to cover the image on
the screen with a gray mask. Use the Disc
Pad to reveal the image. Press Reveal again
to return full screen projection of image. Text: Not used.
Blank: Replace projected image with
white background. Press again to return
image.
Timer: Displays timer (window in lower
part of screen). Repeated operation of
key toggles on/off. Mouse: Toggle mouse emulation On/Off.
On: The L & R buttons operate
left & right mouse key functions. Drag-and-drop
functions are possible by pressing the Drag
button.
Disc Pad moves Mouse pointer.
Off: L button is the Enter confirmation button. R
button is for menu window. Disc Pad centers
image.
       positioning. Disc Pad centers image.Freeze: Stores (freezes) the projected
image. Press again to return the
projection of the current image.
Magnify: Press to enable magnification
mode. Press +/- buttons to
increase/decrease the magnification factor.
Move Disc Pad to displace the magnified
area within the image. Press Magnify again
to toggle back to normal presentation.
In video mode (NTSC only), press Magnify
to toggle between scaled and unscaled
representation. Pointer: Place a pointing device on the
screen. Use Disc Pad to move pointer. Info: Display information window.
Aux: Toggle On/Off a 3M compatible
device.
Menu window position:
In mouse emulation mode:
  right mouse Button (R).
Not in mouse emulation mode:
  keep button pressed while moving
  menu window with Disc Pad around 
						

							14 3M Multimedia Projector MP8760 3M IPC 2000
ENGLISH
5-2. Meaning Of The Icons
An icon will display to indicate a presentation tool is active.
Pointer mode
Activate with Pointer button on IR-Remote control
In the Pointer mode you can move a pointer over and arround the picture area.
By pressing the Pointer button on the remote control a second time it will be turned off.
Freeze mode
Activate with Freeze button on IR-Remote control
In the Freeze mode the picture will be freezed.
Pressing the Freeze button on the remote control a second time or the Magnify button, the freeze mode will be turned
off.
Magnify mode
Activate with Magnify button on IR-Remote control
In the magnify mode the image can be magnified (zoomed). With the –(1) and +(3) buttons you can decrease or
increase the magnifying factor. You can select the magnified area by using the Disc Pad.
Pressing the Magnify button on the remote control a second time, the magnify mode will be turned off.
Reveal mode
Activate with Reveal (7) button on IR-Remote control
In the reveal mode the picture will be covered by a grey sheet. You now can reveal the covered image by using Disc
Pad. Pressing the Reveal button on the remote control a second time, the reveal mode will be turned off.
Muting mode
Activate with Mute button on IR-Remote control
In the muting mode the sound output of the projectors internal speakers and the external output will be muted.
Pressing the Mute button on the remote control a second time, the muting mode will be turned off.
Mouse emulation (Only in data mode [PC/RGB _] available!)
Activate with Mouse button on IR-Remote control
If you’ve connected the projector with the mouse cable and the right adapters to your PC and turned on the projector
before booting the PC it will emulate a mouse over the IR remote control transmitter.
By pressing the Mouse button on the IR remote control the mouse emulation will be activated. You can move arround
the mouse pointer with the Disc Pad. The Disc Pad is pressure sensitive, that means so stronger you press the pad so
faster the mouse pointer will move. The mouse buttons will be emulated by the two buttons left and right beside the
Discpad. . The drag function can be emulated by the Drag (2) button below the Disc Pad. The mouse emulation can
be turned off by pressing the Mouse button a second time. 
						

							 3M IPC 2000 3M Multimedia Projector MP8760 15
ENGLISH
5-2.  Meaning Of The Icons, continued
Question mark
A question mark in a box will appear if the projector can’t recognize
the mode of the data input source.
Even if you select a standard VESA mode on your system this can happen, because some device drivers of the graphic
cards in the PC using timing parameters which differ from the parameters given out from the VESA organization.
As a result of this, the projector may detects a wrong predefined data mode or switches to a User mode, so you may
see only a part of the whole picture.
To correct this situation you must select manually a data Mode in the Picture menu which should match the mode
you’ve selected on the PC. If there is no matching mode you must select a User mode.
In a User mode you can manually select the Resolution which is normally not choosable.
It may be necessary to correct the Horizontal and Vertical Position and the Tracking and Sync values in the Picture
menu. These values will be stored so the mode can be recognized the next time.
If you’ve accidently misadjusted the values of a standard predefined data mode, you can reset them by selecting Reset
Data Modes in the Advanced Setup menu. The settings of a User mode won’t be affected by this action.
Optimize
The image optimize process ist just in progress – please wait a few seconds!
Looking for signal source...
The projector can not find any input signal on the video and data inputs.
Either there is no input source connected to the projector or the source is giving no output signal.
For RGB/PC input sources you must manually select another Sync Mode recognition in the Advanced Setup menu.