3M Multimedia Projector Mp8610 Operators Manual

Ó3M 1998 3MÔ Multimedia Projector MP8610 7
Section 4: Operating Instructions
4-1. Projector Start Up
Read the Important Safeguards before operating the MP8610 projector.  After all cable connections have
been completed, the projector can be powered up.  For best results, please observe the following start up
sequence.  Refer to Figure 4-1
!Caution
Allow a projector that has been stored in a cold place
to warm up to room temperature before applying
power.
1.
 Press the power switch 
(1) to ON to apply...

83MÔ Multimedia Projector MP8610Ó 3M 1998
4-3. Projector Power Down
Press the Standby button to place the projector in the standby mode.  The cooling fan motor will continue
to run.
9 Note
Switching the power off before the fan has cycled
off, will decrease the life of the projection lamp.
1.
 Wait until the cooling fan motor cycles off then press the main power switch to Off.
2.
 Turn off the power to your input devices.
3.
 To transport the projector, disconnect the power cord, computer cable, mouse...

Ó3M 1998 3MÔ Multimedia Projector MP8610 9
4-5. Menu Adjustments/Settings
Depending on the current video source selection, the menu items for either the Video Menu or the Data
Menu will display.  The table below lists all the menu items that can be adjusted.
An asterisk (*) indicates the item appears on the Data menu only, two asterisks (**) indicate the item
appears on the Video/S-VHS menu only and no marking (  ) indicates the item is common to both menus.
Submenu Menu Item Explanation of...

10 3MÔ Multimedia Projector MP8610Ó 3M 1998
Section 5: Remote Control
5-1. How to Operate the Remote Control
The remote control keypad (Figure 5–3) controls basic projector functions. To use the remote control,
aim the remote toward the projection screen and press the desired button. The remote signal (Figure 5-1)
will bounce off of the projection screen and back to the sensor on the front of the projector.
Figure 5-1.  Remote Control Signal
5-2. Replacing the Batteries
The remote control uses two AAA...

Ó3M 1998 3MÔ Multimedia Projector MP8610 11
5-3. Remote Control Button Functions
Press to switch the projector between Standby
mode (lamp off, fan off) and operation mode (lamp
on, fan on).
PCSwitches to PC mode.
VIDEOSwitches to video mode. When in video mode, the
video source can be selected (Video or S-Video) by
pressing the key repeatedly.
AUXNot used
MENUStart the On Screen Menu System for projector
adjustment.
DISC PADMouse emulation ON, disc pad controls the
movement of the pointing device....

12 3MÔ Multimedia Projector MP8610Ó 3M 1998
Section 6: Lamp Information
6-1. Metal Halide Projection Lamp
The metal halide lamp of the projector has a limited life time (approximately 2000 hours). If the
projected image appears dark or a 
red lamp life indicator bar displays during projector startup, you
should change the lamp and air filter.
9 Important Note
This lamp contains mercury.  Consult your local
hazardous waste regulations and dispose of this
lamp in a proper manner.
6-2. Lamp Life Indicator...

Ó3M 1998 3MÔ Multimedia Projector MP8610 13
6-3. Replacing the Lamp
!Caution
Always unplug the projector when changing the
lamp.  There are high voltage parts inside the
cabinet that may 
cause electric shock.
 
 
!Caution
Allow the projector to cool down for 30 minutes.
Lamp and adjacent metal parts become
extremely hot and can cause 
burns to your
fingers.
 
1.
 Press the Standby button on the projector control panel or remote control and wait for the fan
motor to cycle off.
2.
 Turn off the power...

14 3MÔ Multimedia Projector MP8610Ó 3M 1998
11.
 Install the new lamp (3M Lamp Kit Part Number
 78-6969-8577-5) by pushing down on the ends of
the lamp 
(8) with equal pressure.  Take care to correctly align the lamp with the bubble 
(8a) facing
upward   (see figure 6-3).
9 Important Note
Do not touch lamp glass with fingers.  Hold lamp by
the metal ends only.
12.
 Fold the lamp housing 
(6) into the closed position until the lock tab 
(5) secures it.
13.
 Insert the lamp access door 
(1) and slide it...

Ó 3M 1998 3MÔ Multimedia ProjectorMP8610 15
Section 7: Maintenance
7-1. Replacing The Air Filter
For best performance, replace the air filter each time the projection lamp is changed.  One air filter is
included in each lamp kit 
(3M Part Number 78-6969-8577-5) or air filters are available individually as
(
3M Part Number 78-8118-3476-7).  See Appendix D-1.
9 Note
Periodically check air filter for excess dust or dirt.
Replace or clean as needed.
1.
 Unplug the power cord of the projector.
2.
 Stand the...

16 3MÔ Multimedia Projector MP8610Ó 3M 1998
7-2. Cleaning the Projector
For best performance, keep your projector free of excess dust and surface dirt.
Use a soft cloth to remove dust from the projector housing.  Use 3M
Ô Overhead Cleaner 676 to remove
surface dirt and smudges from the projection lens (Figure 7-3).
!Caution
Always unplug the projector when cleaning. Take care
that no liquids get inside the projector.  There are high
voltage parts inside the cabinet that may 
cause
electric shock.
Figure...