3M Micro Professional Projector Mpro110 Operators Manual

							3M™ Micro Professional Projector MPro110
© 2008 3M. All Rights Reserved.
  11
Operator’s 
Guide
Connecting to a Computer Video Source
There are several types of computers that output a video signal: desktop computers, laptop 
computers, ultra-portable computers and some personal digital assistants ( PDAs). The 
3M MPro110 can project the video from these devices using its VGA port. (1) Connect the 
included VGA Cable to the projector. (2) Connect the VGA Cable to the device’s video output.
Powering On
Slide the power switch to the ON position. The power LED will turn green and the projector 
will energize. The projector will automatically detect the connected cable and switch to the 
appropriate port. Then the projector will detect and display the video source. If the video source 
is not detected, the projector will display a blue image and the name of the selected port: 
CVBS (video) or VGA.
NOTE: The projector will switch to power save mode in 30 seconds if no video or computer 
source is detected. The projector will switch to sleep mode in 60 seconds if there is no 
source. When a source is detected, the projector returns to full operating mode.
Tip: The video output on some devices is turned off by default. Please refer to the device’s 
documentation for details on enabling the video.
Powering Off
Slide the power switch to the OFF position.
Disconnect video, VGA and AC adapter cables. 
12044-PSD_78-6971-1437-5_MPro_Projector_Book.indb   118/21/08   4:48:28 PM 
						

							3M™ Micro Professional Projector MPro110
 12 © 2008 3M. All Rights Reserved.
Operator’s 
GuideImage Size
Increase or decrease the projector-to-wall distance 305 mm (12 in) to 1800 mm (71 in.) to 
project an image ranging from 163 mm to 975 mm ( 6.4 in. to 38.4 in.) wide.
Projector-To-Wall Distance Image Width
305 mm (12 in) 163 mm (6.4 in)
610 mm (24 in) 235 mm (9.3 in)
914 mm (36 in) 355 mm (14 in)
1219 mm (48 in) 523 mm (20.6 in)
1524 mm (60 in) 739 mm (29.1 in)
1800 mm (71 in) 975 mm (38.4 in)
Focus Adjustment
Rotate the focus wheel until the image is clear.
Cleaning Projector
Turn off the projector and disconnect power and other cables.
1 
Use soft cloth to wipe off dust. If the dust is difficult to remove, dampen the cloth with 
2 
clean water and then wipe the projector clean. Then use a clean cloth to dry the projector.
Important Notes Do not use cleaning chemicals or solvents to clean the projector. Cleaning chemicals and 
•	
solvents may cause the plastic parts to discolor. 
12044-PSD_78-6971-1437-5_MPro_Projector_Book.indb   128/21/08   4:48:28 PM 
						

							3M™ Micro Professional Projector MPro110
© 2008 3M. All Rights Reserved.
  13
Operator’s 
Guide
Troubleshooting
Problem CauseSolution
Image is fuzzy Projector-to-screen distance out-
side of limits. Image not focused.Place projector 200–1800 mm 
from wall. Turn focus to sharpen 
image.
Does not run on battery power Battery not charged.  
Battery needs replacement. Plug in AC adapter and turn 
power switch Off to charge bat-
tery. Replace battery if it will not 
hold a charge.
Blank image Power is off.
Projector in Power Saver Mode.Turn projector ON. Input source 
must be powered ON and sending 
an input signal.
LED flashing red Battery is low.Plug in AC adapter and turn 
power switch Off to charge 
battery.
LED is green Projector in Power Saver Mode.Projected images returns when 
input signal resumes.
LED is orange Battery is charging.LED is orange during charging 
and goes off when battery is fully 
charged.
Video or VGA icon is flashing No input signal is detected by 
projector.Turn on power for input source.
Video/VGA icons alternate 
flashing No input cable is detected.
Connect input cable and power 
on input source.
12044-PSD_78-6971-1437-5_MPro_Projector_Book.indb   138/21/08   4:48:28 PM 
						

							3M™ Micro Professional Projector MPro110
 14 © 2008 3M. All Rights Reserved.
Operator’s 
GuideSpecifications
Projector
Description Specification
Imager Technology LCOS
Size 11.9 mm (0.47")
Image Resolution 640 x 480 Pixels
Image Aspect Ratio 4:3
Projection Distance 305–1800 mm (12"–70")
Image Size 163–975 mm (6.4"–38.4")
Throw Ratio (Width/Distance) 0.53
Lens Offset 1:1 (none)
Inputs VGA, Composite Video, DC Power
Compatible Resolution VGA, SVGA, XGA
Refresh Rates 60 Hz
Video Compatibility NTSC, PAL, NTSC (M),  
PAL (BGHI)
Dimensions 115 mm (L) x 50 mm (W) x 22 mm (H)
(4 1/2" x 1 31/32" x 7/8")
Weight 160 g (5.6 oz.)
Tripod Socket ¼"-20
Operating Temperature 10˚–30˚C (50˚–86˚F)
Altitude Sea Level to 1,829 m (6000')
12044-PSD_78-6971-1437-5_MPro_Projector_Book.indb   148/21/08   4:48:29 PM 
						

							3M™ Micro Professional Projector MPro110
© 2008 3M. All Rights Reserved.
  15
Operator’s 
Guide
NK03-S005 Rechargeable Lithium-Ion Battery
Description Specification
Type Rechargeable Lithium-ion Battery
Rated Capacity 3.7 V/ 1050mAh
Dimensions 40.4 x 34.4 x 9.4 mm (1.6” x 1.4” x 0.4”)
Do not throw battery into trash. Please dispose of according to federal, state, or local laws 
Supported Computer Signals
DescriptionResolution (width x height)Refresh Rate
VGA 640 x 48060 Hz
SVGA 800 x 60060 Hz
XGA 1024 x 76860 Hz
Replacement Parts / Accessories
Description3M Part Number
US AC Power Adapter 78-6969-9972-7
EU/UK AC Power Adapter 78-6969-9977-6
Rechargeable Battery 78-6969-9974-3
AV Cable Kit   
( Video Cable and RCA Adapter) 78-6969-9979-2
VGA Cable 78-6969-9978-4
12044-PSD_78-6971-1437-5_MPro_Projector_Book.indb   158/21/08   4:48:29 PM 
						

							3M™ Micro Professional Projector MPro110
 16 © 2008 3M. All Rights Reserved.
Operator’s 
GuideLimited Warranty
The 3M
•	™ Micro Professional Projector MPro110 (the “3M product” ) is warranted to 
be free from defects in material or manufacture for a period of 90 days from the date 
of purchase. 
All other accessories included with the 3M product are warranted to be free from defects 
•	
in material or manufacture for a period of 90 days from the date of purchase. 
Optional product accessories that are not sold as part of the 3M product are subject to 
•	
individual warranties.
THE WARR ANTIES STATED ABOVE ARE EXCLUSIVE AND ARE MADE IN PL ACE OF ANY AND 
ALL WARR ANTIES, EXPRESS OR IMPLIED WARR ANTIES OR CONDITIONS, INCLUDING ANY 
IMPLIED WARR ANT Y OF MERCHANTABILIT Y OR FITNESS FOR A PARTICUL AR PURPOSE, OR 
ANY INDUSTRY PR ACTICE OR CUSTOM OR TR ADE USAGE. 
In the event the 3M product fails to conform to the above stated warranties within the 
applicable warranty period, your exclusive remedy shall be, at 3M’s option, to replace or 
repair the 3M product or to refund the purchase price of the 3M product. All replaced parts 
or products become property of 3M. If the product is repaired, 3M will repair the defective 
part(s) with a new or used part(s). If the 3M product is replaced, 3M will replace the 3M 
product with the same or equivalent model and with a new or refurbished 3M product. In the 
case of an approved warranty claim, the replacement 3M product will carry only the remaining 
term of the original 3M product’s warranty period as stated above. For warranty service, you 
must provide proof of the date of the original purchase else the manufacturing code date will 
be used to establish the start date of the warranty. The following are exclusions to the above 
listed warranty: This warranty does not cover 3M product that is modified or damaged through improper 
a. 
storage, misuse, abuse, accident, vandalism, improper installation, neglect, improper 
shipping, damage caused by acts of war, disasters such as fire, flood, and lightning, 
improper electrical current, software problems, interaction with non-3M products, or 
service other than by an 3M Authorized Service Provider, neglect or mishandling by any 
person. Normal wear and tear is not covered under warranty.
12044-PSD_78-6971-1437-5_MPro_Projector_Book.indb   168/21/08   4:48:29 PM 
						

							3M™ Micro Professional Projector MPro110
© 2008 3M. All Rights Reserved.
  17
Operator’s 
Guide
3M product is designed to operate in the typical indoor environment. This warranty does 
b.  
not cover 3M product used outside of the following circumstances:
100V–240V AC, 50 /60 Hz 
•	
10° to 30° C ( 50° to 86° F ) 
•	
10 –80% RH (without condensation) 
•	
0 –1828m ( 0 – 6000 feet) above sea level
•	
Environments with high levels of smoke or air born particulates
•	
The air intake and exhaust vent must be clear of obstructions. Inadequate air ventilation 
c.  
will cause the 3M product to malfunction or will cause damage to the 3M product which 
will void the warranty.
This warranty does not cover any additional costs including, but not limited to, those 
d. 
associated with removal, cleaning or installation of the 3M product, adjustments, 
(mechanical or electronic) made to the 3M product. 
This warranty covers only normal use of the product. 24-hour-per-day or other excessive 
e.  
continual use causes strain and is not considered normal use. 
This warranty does not cover consumables (e.g., fuses), other than lamps and only as set 
f.  
forth below. 
This warranty is not transferable. 
g.  
3M is not responsible for warranty service should the 3M label or logo or the rating 
h.  
label or serial number be removed unless otherwise stated in writing for the purposed of 
private labeling for partnership requirements. 
This warranty does not cover postage, insurance, or shipping costs incurred in presenting 
i. 
your 3M product for warranty service. Said costs are the customer’s responsibility. If a 
claimed defect cannot be identified or reproduced in service, the customer may be held 
responsible for cost incurred. Should your warranty upgrade include a “change out” 
service and the claimed defect cannot be identified or reproduced by the technician, the 
customer will be responsible for call out costs.
FAILURE TO FOLLOW THE INSTRUCTIONS CONTAINED IN THE APPROPRIATE 3M 
product MANUAL OR TO USE THE 3M PRODUCT IN ACCORDANCE WITH 3M’S 
INTENDED USE STATEMENT, WILL VOID ALL WARRANTIES AND LIMITED REMEDIES.
12044-PSD_78-6971-1437-5_MPro_Projector_Book.indb   178/21/08   4:48:29 PM 
						

							3M™ Micro Professional Projector MPro110
 18 © 2008 3M. All Rights Reserved.
Operator’s 
GuideEXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL, 3M SHALL 
NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES 
( INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, REVENUE OR BUSINESS ) RESULTING 
FROM, OR IN ANY WAY REL ATED TO PERFORMANCE, USE OR INABILIT Y TO USE ANY OF 
THE 3M PRODUCT. This limitation applies regardless of the legal theory upon which damages 
are sought.
For warranty support, please call or write your local 3M office or a 3M Authorized Service 
Provider to obtain an RMA # ( Return Material Authorization number) before returning 
the product. If you are inside the Continental United States of America, please contact 
3M Customer Service at 1-866-631-1656 or email meetings@ mmm.com .
What 3M Will Do To Correct Problems : If your 3M product requires service, 3M will ask you to bring or send the 3M product, 
•	
securely packaged in its original container or equivalent, along with proof of the date of 
original purchase, to your 3M Service Dealer or 3M Service Center. 
3M will, at its option, repair or replace the defective unit without charge for parts or labor. 
•	
Return of the 3M product will be at 3M’s expense. 
When warranty service involves the exchange of the 3M product or of a part, the item 
•	
replaced becomes 3M property. 
The exchanged 3M product or part may be new or previously refurbished to the 
•	
3M standard of quality, and at 3M’s option, the replacement may be another model of 
like kind and quality. 
3M’s liability for replacement of the warranted 3M product or part will not exceed the 
•	
original retail selling price of the 3M product. Exchange or replacement products or parts 
assume the remaining warranty period of the product covered by this limited warranty. 
However, each replacement lamp carries the limited 90-day warranty stated above.
12044-PSD_78-6971-1437-5_MPro_Projector_Book.indb   188/21/08   4:48:29 PM 
						

							3M
™
 Micro Professional Projector 
MPro110
Operator’s Guide
Guide de l’utilisateur
Bedienungsanleitung
Guía para el operador Guida utente
Gebruiksaanwijzing Användarmanual 用户指南
使用手冊
Projection Systems
3M Austin Center
6801 River Place Blvd.
Austin, T X 78726-9000
866-631-1656
www.3M.com/meetings
e-mail: meetings @ mmm.com Please recycle. Printed in Taiwan.
© 3M 2008. All rights reserved.
August 2008 78-6971-1437-5-B
3M is a trademark of 3M Company.
3M est une marque commerciale de 3M Company. 3M es una marca registrada de la Compañía 3M. 3M è un marchio commerciale 3M Company. 3M ist ein Warenzeichen der Firma 3M.
3M is een handelsmerk van 3M Company.
3M är ett varumärke tillhörande 3M Company.
3M
™ Micro Professional Projector  MPro110