3D Perception CompactViewn Sx25+i User Manual

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  26 
 
 
 
16.4  Set Up Sub-menu 
keystone V  
Adjust vertical keystone correction. Compensates fo
r 
the geometrical distortion of the projected image 
resulting from tilting the projector to shoot highe r up 
on the wall.    
keystone H  
Adjust horizontal keystone correction. Compensates  
for the geometrical distortion of the projected ima ge 
resulting from shooting the image at an angle 
sideways on the screen.    
DPMS 
Activate/deactivate DPMS (Display Power  
Management Signaling). When DPMS is on, the  
projector will switch off following the powering of f or 
disconnection of the signal source. The projector w ill 
switch back on when the signal source is reactivate d. 
 
source scan  
Switches source scan on and off. With source scan  
on, the projector will search for another source if  the 
current source is disconnected or switched off. 
With source scan off, the projector will remain at  the 
selected source input even if the source is switche d 
off or disconnected.    
orientation  
Select between desktop front, desktop rear, ceiling  
front and ceiling rear mode. The image will be flipp ed 
and reversed accordingly.    
OSD  
Select the required position on the OSD (On Screen  
Display)   
language 
Select between languages    
RGB video  
Selects RGB video on the component video input  
(YPbPr). Requires composite sync connected to the 
composite video input.
 
FOR ALL 
 
    
						

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  27 
 
 
16.5  Utilities Sub-menu 
FOR ALL 
 
information  
Displays information about the source and projector
 
status   
OSD  
Turn the On Screen Display on (display) or off (hid e) 
during source scan.  
OSD timeout  
Defines how long OSD is displayed after last key 
action before it disappears from the screen.   
OSD background  
Select background mode, whether translucent or  
opaque.    
reset  
Resets the projector to its basic settings. All  
parameters available in the various menus are reset  
to their factory values. 
Note:  Control mode will automatically be reset to 
RS232 even if the projector is a type SX25+I. A 
power cycle is needed for the projector to detect  
the presence of a GCM card and to select the  
RIMI mode 
 
lamp reset  
Reset lamp after lamp change. Do not reset lamp  
counter unless the lamp has been replaced with an  
original new lamp.    
service menu  
For service personnel only. A special service code  is 
needed to access internal calibration controls and 
status information. Not accessible to the user.    
test image 
Applies a fixed test image for set-up purposes
 
  SYSTEM INFORMATION 
 
     
						

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  28 
 
 
16.6  Control Sub-menu 
mode  
Selects between RS232, RIMI (internal) and LAN  
control modes. The projector can be controlled by  
only one of the modes at a time.    
When using the CompactView SX25+I the mode must  
be set to RIMI (Rich Media Interface). When a GCM  
has been installed, the projector will detect its  
presence after a power cycle and select RIMI. 
Note:  Reset to factory default will automatically 
reset to RS232. 
  
RS232 address  
For use when daisy-chaining several units. Select  
auto or fixed address. Only one address scheme is  
allowed per daisy-chain. The auto address is  
allocated following the relative position in the da isy-
chain. The fixed address is an absolute address. On ly 
unique fixed addresses are allowed.    
RS232 fixed  
Select a unique fixed address in the range availabl e. 
 
baudrate  
Selects between baud rates 4800, 9600 and 19200. A  
lower baud rate may be required in installations wi th 
long cable runs.
 
  FOR ALL 
 
    
						

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  29 
 
 
17.  MAINTENANCE 
The projector may from time to time require cleanin
g. Never open the projector, as this will void 
any warranties. Refer all service and repair work t o qualified personnel. 
  
Only the exterior of the projector may be cleaned.  Use a damp cloth. Make sure no liquids enter 
the inside of the projector              
Vacuum-clean all the air vents regularly to  
maintain sufficient air flow. 
             
The  projection  lens  is  sensitive  to 
scratches.  Use  lens-cleaning  tissue,  
available  at  all  photographic  shops  when 
cleaning the projection lens. Use lens cap 
when not in use. 
      
						

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  30 
 
 
18.  LAMP REPLACEMENT 
The STATUS lamp on the keypad will turn red when th
e lamp life expires. In addition, a 
message will appear on the screen; “LAMP LIFE TIME  HAS EXPIRED! Please change lamp.”  
 
18.1  Remove old lamp 
Change the lamp when its lifetime expires. Always replace the lamp with the same type and 
rating.      
Always disconnect the power cord and wait  
until the projector has cooled down (60  
minutes) before opening the lamp cover.    
Release the screw (A).   
Remove the lamp cover (B).   
  
       
Release the 3 screws on the lamp house  
(C).         
 
     
						

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  31 
 
 
      
Pull the handle (D).    
Remove the lamp house (E). 
 
18.2  Insert New Lamp  
          
Replace the lamp house (E)    
 
       
Fold the handle (D) back in to place.    
Tighten the 3 screws (C)       
 
      
						

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  32 
 
 
        
Replace the lamp cover (B)    
Tighten the screw (A).    
In the “utilities” sub menu, reset the lamp  
timer. 
 
      
						

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  33 
 
 
19.  SERVICE INFORMATION 
This product contains no user-serviceable parts.    
If the product fails to function as expected, first
 check that all connections are properly made, 
and that the power cord is properly connected.    
Check that the projector and the video and computer  sources are all switched on. 
 
Cables and cords may break over time. Try changing  the cables and cords in case there is a 
bad or intermittent connection.   
Check if the circuit breaker or the fuse of the mai ns is intact. 
 
In the event of product failure, please contact you r reseller. You should prepare a description of 
the symptoms of failure you experience. Also state  the projector number and serial number as 
printed on the label on the bottom of the projector . 
   
						

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  34 
 
 
20.  TECHNICAL DATA 
20.1  Projector Specifications 
 
Resolution 1400 x 1050 (native) SXGA+ 
Display technology Single chip DLP™ technology by Texas Instruments® 
Display device LVDS DMD™ with DarkChip2™ technology 
Computer Compatibility UXGA, SXGA+, SXGA, XGA, SVGA, VGA   
PC, MAC, SGI and other workstations 
RGBHV, RGBS, RGsB 
Video Compatibility HDTV (1080i, 720p, 576i/p, 480i/p) NTSC, NTSC 4.43, 
PAL, PAL-M, 
PAL-N, SECAM. Faroudja™ de-interlacing with  
automatic film mode detection (3 : 2 and 2 : 2 pull -down) 
Aspect ratio 4 : 3 (native), 16 : 9 / 5 : 4 (compatible) 
Bandwidth Up to 205 MHz on analog RGB  
Up to 160 MHz on DVI  
Up to 75 MHz on component input 
Brightness Up to 2500 lumen  
Contrast Up to 2500 : 1  
Wide angle lens f = 19.5  
F = 2.8  
throw ratio = 1 : 1 (distance : width)  
throw distance = 1.5m - 20m / 5 - 66 ft.  
Image width = 1.5m - 20m / 2.3 - 66 ft.  
offset = 108% 
Zoom lens f = 33 - 42  
F = 2.75 - 3.1  
Zoom factor = x 1.25 
throw ratio = 1.70 - 2.2 : 1 (distance : width) 
throw distance = 1.5m -10m / 5 - 33 ft.  
image width = 0.7m - 5.7m / 2.3 - 18.8 ft.  
offset = 108% 
Lamp 250W UHP™ dimmable to 200W 
Lamp life 2000 hrs (typ) to 50% brightness @ 250W  
4000 hrs (typ) to 50% brightness @ 200W 
Noise level 28 dB (typ), 32 dB (max) @ 20°C/68°F, sea  
level 
Dimensions 244 x 278 x 88 mm / 9.6 x 10.9 x 3.5, excluding len s 
Weight 3.4 kg / 7.5 lbs 
   
						

							3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  35 
 
 
 
Inputs 2 VGA 15 pin female HD-DSUB analog RGBHV  
1 DVI-D female digital RGB  
1 Component video female 3 x RCA/phono  
1 S-video female 4 pin mini-DIN  
1 C-video female RCA/phono  
2 Audio 3.5 mm female stereo jack 
1 RS 232 9 pin female DSUB (control, firmware updat
e) 
1 USB-B female (control, firmware update)  
1 LAN RJ-45 female (control, firmware update)  
1 Remote Control 3.5 mm female stereo jack 
Outputs 1 VGA Monitor 15 pin female HD-DSUB analog RGBHV  
1 Audio 3.5 mm female stereo jack 
1 RS 232 9 pin male DSUB 
Power 90-260 VAC, 50-60 Hz, 350W 
Conformance CE, FCC A, CSA(C,US) 
Temperature operating 0-40°C / 32-104°F, 0-1500 m / 0-4950 ft  
0-35°C / 32-95°F, 1500-3000 m / 4950-9900 ft 
Temperature storage -20 - 60°C / -4 - 140°F 
Humidity operating 20-90% RH, non-condensing 
Humidity storage 10-95% RH, non-condensing 
 
20.2  GCM Specifications  
These specifications apply to the CompactView SX25+ I only 
 
Non-linear image mapping from 50% to 200 % 
Total latency typically 250 line period 
Automatic and manual options 
Up to 100 geometrical control points (compliant wit h curved 
screens requirements) 
Warping 
Up to 5th order approximation between geometrical c ontrol points 
Multisided non-linear blending from 2% to 100% of total image 
Alpha adjustable from 0 to 4 across overlapped area s 
Gamma adjustable from 0.25 to 4 in overlapped areas  
Soft Edge Blending 
Up to 5 geometrical control points (compliant with  curved screens 
requirements) 
Individual RGB adjustments of ± 20% in addition to  native 
adjustment capabilities 
Primary Colour Calibration (For ‘E’ models with Com pactUTM zer0 
only) 
Colour 
Input Offset and Input Gain adjustments 
Gamma  Individual RGB adjustments from 0.25 to 4 in  addition to native 
adjustment capabilities 
 
Specifications are subject to change without prior  notice. All values may vary up to +/- 20%.