3D Perception COMPACTVIEW Hmr 15 User Manual

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 17 
 
 
8.  USING THE PROJECTOR 
After set-up, switch on all equipment. 
8.1  Projector On/Off 
To switch the projector On, firmly press the POWER 
button on the top of the projector (A) or the 
remote control button (B) on the Control dialogue p age in CompactControl.  
  
The STATUS indicator (C) will turn green when the p rojector is switched On and yellow when 
the projector is switched to standby.   
A
C
 
B
 To...

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 18 
 
 
9.  MAINTENANCE 
The projector may from time to time require cleanin
g.  
  
Only the exterior of the projector may be cleaned.  Use a damp cloth. Make sure no liquids enter 
the inside of the projector.   
With the exception of when changing a lamp, never o pen the projector, as this will void any 
warranties. Refer all service and repair work to qu alified personnel. 
         

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 19 
 
 
10.  LAMP REPLACEMENT 
Always replace the lamp with the same type and rati
ng. 
10.1  Remove old lamp 
      
Remove the cover of the lamp  
housing (A) by undoing the   
fixing screw (B) and sliding the  
cover forward.. 
A
B
 
 
    
Undo the locking screw (C)   
and disconnect the wiring  
element (D).    
Remove the lamp unit (E). 
C
D
E
                       

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 20 
 
 
10.2  Insert New Lamp  
      
Replace the lamp unit (E).     
Re-connect the wiring element  
(D).     
Fasten the locking screw (C) 
C
D
E
 
 
      
Slide the cover of the housing  
unit (A) back into position.     
Re-fasten the  fixing screw (B) 
 
A
B
       
NOTE
: It is most important to ensure that the cover of  the lamp housing is correctly sited back in 
its slot. If it is not firmly back in position...

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 21 
 
 
11.  SERVICE INFORMATION 
This product contains no user-serviceable parts.    
If the product fails to function as expected comple
te the following steps:  
  1.  Check that all connections are properly made, an d that the power cord is properly 
connected. 
 
2.  Check that the projector, the video and the comp uter sources are all switched on. 
  3.  Check that the circuit breaker and the mains fus e is intact....

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 22 
 
 
12.  TECHNICAL DATA 
12.1  Warping and edge blending specifications 
Warping 
Non-linear image mapping from 50% to 200% 
  Processing latency from 50 µs to 12 ms dependent o n mapping level 
  Total latency 250 line period  
  Automatic and manual options  
  Up to 100 geometrical control points (compliant wi th curved screen requirement) 
  Up to 5
th order approximation between geometrical control po ints...

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 23 
 
 
12.2  Projector specifications 
Resolution (native) 
1024 x 768 
   
Technology  DDR – Double Data Rate DMD
TM Module 
  DLPTM by Texas Instruments 
   
Compatibility  For PC’s, Macs, SGI and other workstations 
   
Computer interface  UXGA, SXGA+, SXGA, XGA and SVGA 
   
Inputs  1 VGA 15 pin DSUB (Analogue RGB) 
  1 DVI (Digital RGB) 
  5 BNC (Analogue RGB) 
   
Remote control  via CompactControl:   2 x RS232...

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 24 
 
 
13.  LIMITED WARRANTY, ‘FCC STATEMENT’ AND 
‘TRADEMARKS COPYRIGHT’ 
Limited Warranty  
Except  as  otherwise  stated  herein,  3D  perception  wa
rrants  that  a C
OMPACTVIEW HMR-15 
projector  is  free  from  defects  in  parts  and  labour  under  normal  use  during  the  warranty  period. 
The  warranty  period  means  the  24-month  period  from  the  date  of  purchase  of  a 
C
OMPACTVIEW 
HMR-15 projector....

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 25 
 
 
Procedure for claims  
Any and all questions or claims concerning a 
C
OMPACTVIEW HMR-15 projector shall be made to 
3D  perception  authorised  personnel  through  the  VAR  from  whom  the C
OMPACTVIEW HMR-15 
projector  was  purchased.  In  no  case  shall  a  C
OMPACTVIEW HMR-15  projector  be  returned 
without  first  securing  the  authority  of  3D  percepti on  or  its  authorised  personnel.  Any...

3D perception   COMPACTVIEW HMR-15 
Revision 1                    User Manual   
 
 26 
 
 
14.  CONTACT US 
Head Office 
3D PERCEPTION AS  
Solbråveien 41  
P. O. Box 455  
N1373 Asker   
Norway    
Tel:  +47 66 98 70 70  
Fax:  +47 66 98 70 71  
Support desk:  +47 66 98 70 90    
e-mail (sales):  [email protected] 
e-mail (tech support):  [email protected]    
Web site  www.3d-perception.com   
USA Office 
3D PERCEPTION Inc 
1277 N. Semoran Boulevard  
Suite 117 
Orlando FL 32807 
 
Tel:...