- INSTRUCTIONS -
Form C Relay for 12-18V DC Intercom Systems with Door Release
WIRING DIAGRAMS:
Page 1
INSTALLATION:
1. Install in a suitable location, either near the power source for the door release mechanism, or behind the intercom.
2. Secure wire connections with proper termination, such as wire nuts or crimp connectors.
3. Trim the wires to the desired length.
4. Cut the unused contact wire so the bare strands are not exposed.
RY-18L COLOR CODE:
Input of Relay:
Red:L/RED, Postive trigger
Gray:(-)...
- INSTRUCTIONS -
The RY-24L Door Release Relay Module is an interface between the door release contact on the Aiphone monitor and the
actual release mechanism. The contact closure directly out of the monitor is rated at 12V AC with a low current capacity. If
your strike or maglock requires more voltage or current, the RY-24L is required. It provides either a Normally Open contact
for an electric strike, or a Normally Closed contact for a magnetic lock. The contact rating supports a majority of door...
0316
RY-ES InstructionsPg. 1
The RY-ES is a relay used to activate an external signaling device when the do\
or station calls in. It can be
used for call extension on the JP, JO, JK, JF, KB, AX, NIM, DB, and IE systems (excluding IE-8MD). The
relay connects to the chime output of the master station in place of the\
IER-2. The RY-ES relay will share
power with the master station.
RY-ES
External Signaling Relay
- INSTALLATION & OPERATION INSTRUCTIONS -
Input of relay:
Red: Positive Power
Black:...
RY-IP44
Programming Manual
For use with IX Series, IS-IP Series, and IPW-1A
This is the programming manual for the RY-IP44 only. Refer to the Installation and Setting
Manuals for the series being integrated with for complete installation/programming information
on each system (IX, IS-IP, IPW-1A).
0416
Input/Output Network Adaptor
ATTENTION:
#95101
SBX-1G
Stainless Steel Surface Mount Box
The SBX-1G is a surface mount stainless steel enclosure designed for mounting the LE-SS-1G and
NE-SS-1G subs. The enclosure is weather resistant and includes space inside for wiring.
-INSTRUCTIONS-
SBX-1G Instr.0512JD
Aiphone Corporation1700 130th AVE NEBellevue, WA 98005(425) 455-0510 Fax: (425) 455-0071
TOLL FREE TECHNICAL SUPPORT:
(800) 692-0200
E-MAIL: [email protected]
MOUNTING:
1. Mount the SBX-1G to a wall surface.
2. Connect supplied speed nuts to the...
- INSTRUCTIONS -
The SBX-2G is a surface mount stainless steel enclosure designed for mounting Aiphone 2-gang sub
stations. The enclosure is weather resistant and includes space inside for wiring. The unit mounts to a 1-gang
box or ring, or mounts directly to a wall surface.
SBX-2G
Stainless Steel Surface Mount Box for 2-Gang Sub Stations
SBX-2G Instr.
0913JD
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
(425) 455-0510
FAX (425) 455-0071
Toll Free Technical Support:...
SBX-ACE
Stainless Steel Enclosure for Intercom Door Station and
Access Control Device (i.e. card or proximity reader, keypad)
The SBX-ACE is a surface mount stainless steel enclosure designed for mo\
unting an Aiphone 1-gang surface
mount door station and an access control device side by side. This enclosure can be used as a stand-alone
box for mounting any card or proximity reader, or other device requiring a hooded outdoor box.
The SBX-ACE includes room inside for wiring and is weather resistant....
- INSTRUCTIONS -
The SBX-AXDV30 is an 18-Gauge stainless steel surface mount 30° box designed for angle mounting the
AX-DV video door station. This is applicable for wide or double door entrances where the door station
needs to be mounted off to the side of the door, and provides a better viewing angle for the camera.
Stainless Steel 30° Angle Box for the AX-DV
MOUNTING INSTRUCTIONS:
1. The SBX-AXDV30 is designed to mount to a 1-gang
box or ring, or to any flat surface.
2. Pass cable through the...
- INSTRUCTIONS -
The SBX-AXDVF is an 18-Gauge stainless steel enclosure designed for surface mounting the AX-DVF
video door station.
Stainless Steel Surface Mount Box for the AX-DVF
5-
7/8
2
-
1
3
/1
6
9-¾”
1
-
15
/1
6
1. The SBX-AXDVF is designed to mount to a 1- or 2-gang
box, ring, or to any flat surface.
2. Pass cable through the knockout hole.
3. Secure mounting box to wall.
4. Connect CAT-5e cable to AX-DVF.
(Refer to system’s installation instructions.)
5. Connect supplied speed nuts to...
- INSTRUCTIONS -
The SBX-DV30 is an 18-Gauge stainless steel surface mount 30° box designed for angle mounting the
JF-DV, JK-DV, JO-DV, and JP-DV video door stations. This is applicable for wide or double door entrances
where the door station needs to be mounted off to the side of the door, and provides a better viewing angle
for the camera.
Stainless Steel 30° Angle Box for the
JF-DV, JK-DV, JO-DV, & JP-DV
SPECIFICATIONS:
Mounting: 1-gang box, or surface mount directly to wall surface
Material:...
- INSTRUCTIONS -
The SBX-DVF is an 18-Gauge stainless steel enclosure designed for surface mounting the JF-DVF,
JK-DVF, JO-DVF, and JP-DVF video door stations.
Stainless Steel Surface Mount Box
5-
½
”3
-
3/1
6
8-5/16”
2
-
½”
1. The SBX-DVF is designed to mount to a 1- or 2-gang
box, ring, or to any flat surface.
2. Pass cable through the knockout hole.
3. Secure mounting box to wall.
4. Connect wires to JF-DVF, JK-DVF, JO-DVF, or JP-DVF.
(Refer to system’s installation instructions.)
5. Connect...
- INSTRUCTIONS -
Stainless Steel Surface Mount Box
For units with embedded card readers and access keypads
5-15/
16
2
-1
3
/
16
11-3/4”
1-
15
/16
1. The SBX-DVF-P is designed to mount to a 1- or 2-gang
box, ring, or to any flat surface.
2. Pass cable through the center opening.
3. Secure mounting box to wall.
4. Connect the proper cable to the video door station.
(Refer to the system’s installation manual.)
5. Connect supplied speed nuts to mounting tabs. (4 total)
6. Attach video door station to...
