Zenith Projector Lxg 120 User Manual
Have a look at the manual Zenith Projector Lxg 120 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10 Zenith manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
20 Connecting to a Macintosh PowerBook Connections a.Connect either end of the computer cable tothe Computer In of the projector. b. Set the adjusting number and letter of the Macintosh desktop adapter to the resolution you want to use and connect the adapter to the Macintosh PowerBook.(Refer to page 18-19) c.Connect the other end of the computer cable to the Macintosh desktop adapter. d.Connect the audio cable from the PC to the Computer Audio of the projector. e.Connect the mouse cable from the Macintosh mouse port to the Mouse of the projector. Computer Out Computer In Mouse Computer Audio K AudioVideoS-VideoRL/MONO 1 2 3 4 5 6 7 8 9ONb c da e INSTALLATION AND CONNECTION
21 Connecting to a Video Source Standard Audio/Video Connection a.When connecting the projector to an A/V source, connect the A/V input ports of the projector to the out- put ports of the A/V source with A/V cables of the same color. The video cable is yellow. The left audio is white and right audio is red. S-VHS Video Connection b.Connect S-Video input port of the projector to S-Video output port of A/V source with S-Video cable. * For better picture quality, use the S-Video connection rather than the A/V connection. * If you connect S-Video cable and Video cable simultaneously, only the S-Video source will be displayed. * For Mono Audio Input, connect the single audio cable to the Audio Lport of the projector. lIn AV input mode, if the auto video system recognition fails to detect a correct video input signal, press the auto trackingbutton on the remote control. lYou can connect a VCR, a camcorder, a DVD or any other compatible video image source to the projector. Computer OutComputer In Mouse Computer Audio K AudioVideoS-VideoRL/MONOS VIDEO (R) AUDIO (L) VIDEO OUT IN a b
Connecting to a DTV Settop Box Computer OutComputer In Mouse Computer Audio K AudioVideoS-VideoRL/MONO DTV OUT(R) AUDIO (L) Connections a.Connect the Computer In of the projector to DTV OUTof the D-TV Set-top Box. b.Connect the Audio input ports (R, L/Mono) of the projector to the Audio output ports (R, L) of the D-TV Set-top Box. lTo receive HDTV programing, a DTV receiver (Set-top Box) must be connected to the projector. a b DTV Set-top Box 22INSTALLATION AND CONNECTION
23 Turning on the Projector Remove the lens cover of the projector. Press the main power button on the back panel. 1 Press the powerbutton on the remote control or top cover. (Green operation indicator flashes during warming up of the lamp.) lAn image appears after the green power indicator has flashed for some time. 3 2 Adjust volume level. lPress volumebuttons to increase or decrease sound level.5 24 •Do not shut off the main power (back panel switch) or unplug the power cord while the ventilation fan is in operation.POWERMENU SOURCEBLANKENTER VOL-VOL+ Select the source mode. lPress the sourcebutton repeatedly to change between PC and A/V Inputs.4
BASIC FUNCTIONS 24 Focusing and Positioning the Screen Image Focusing and Positioning the Screen Image When an image appears on the screen, make certain that the picture is focused and fits prop- erly on the screen. l To adjust the focus of the image, rotate the focus (outer) ring on the lens. l To adjust the size of the image, rotate the zoom (inner) ring on the lens. To raise or lower the image on the screen, extend or retract the foot at the bottom of the pro- jector by pushing foot adjuster as shown below. 1.Carefully press the foot adjuster button while you support the other side of the projector. This unlocks the foot and allows it move freely. Be careful not to drop the projector. 2.While pressing the foot adjuster button, raise or lower the projector to place the image in the proper position on the screen. 3.Release the button to lock the foot in its new position. 4.To fine-tune the height of the projector, rotate the front foot to raise or lower it. 5.Once the projector height has been adjusted, do not press down on the projector. POWER MENU SOURCEBLANKENTER VOL-VOL+ Focus ring Zoom ring Push Operating the Projector
25 If the projector is installed on a surface that is not stable or flat, the projected image shape will be distorted. POWER MENU SOURCEBLANKENTER VOL-VOL+ Horizontal leveler l To correct this condition, adjust the projector’s position using the horizontal leveler as shown above. Operating the Projector
Function checking 3 Press the menubutton. 1 Move the pointerbutton up or down to select a menu and press the enterbutton. Each press of the button will cycle through the available menus. Move the pointerbutton up or downto select a function that you want to use or adjust. lWithout an input signal from a PC or Video source, the On-Screen Display (OSD) doesn’t appear. lTo exit the menu display, press the menubutton repeatedly. *In AV mode, Horizontal/ Verticalin POSITION menu, VGATextin SPECIALmenu and TRACKING menu are not displayed. *The sub menus for the VIDEO menu in AV mode are different from those in the PC mode (Refer to page 41). 2 exit move enterMenu MenuGVIDEOG POSITIONGSPECIALG TRACKING exit move adjustMenu MenuEVIDEOContrast Brightness Color R Color G Color B Reset GPOSITIONGSPECIALGTRACKING 80 80 exit move adjustMenu Menu GVIDEOEPOSITIONHorizontal Vertical Keystone Zoom Resize G SPECIALG TRACKING exit move selectMenu Menu G VIDEOG POSITIONESPECIALLanguage Flip Horizontal Flip Vertical Blank Image Lamp Time VGA Text G TRACKING exit move enterMenu Menu G VIDEOG POSITIONG SPECIALETRACKINGAuto Tracking Clock PhasePress Enter to Start 0 0EnglishG 26 BASIC FUNCTIONS
Selecting source mode Press the sourcebutton 1 Each press of the sourcebutton changes the display as shown below. 2 PCAV 27
Using Still function Press the stillbutton. • You can freeze the input image from a PC or AV source.1 To return to normal video, press the stillbutton again. 2 Moving ImageStill Image 28 BASIC FUNCTIONS
Selecting language Press the menubutton and move the pointerbutton up or downto select the SPECIALmenu as shown below. 1 Press the enterbutton and move the pointerbutton up or downto select the Languageitem. Move the pointerbutton left or right to select the language you want to use. l On-Screen-Display(OSD) will change to the language chosen.lTo exit the menu display, press the menubutton repeatedly. 2 3 exit move enterMenu MenuG VIDEOG POSITIONG SPECIALG TRACKING exit move selectMenu Menu G VIDEOG POSITIONESPECIALLanguage Flip Horizontal Flip Vertical Blank Image Lamp Time VGA Text G TRACKING EnglishG 29