Zanussi Zws 588 User Manual

Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
OptionsDetergent
Compartment
SYNTHETICS
NORMAL + PREWASH
60°-Cold
Prewash - Main wash - Rinses
Maximum spin speed 600 rpm for ZWS 568
Maximum spin speed 800 rpm for ZWS 588
Max. load 3 kg - Reduced load 1.5 kg 
1)
Synthetic or mixed fabrics: underwear, coloured garments,
non-shrink shirts, blouses.
SPIN, RINSE HOLD,
EASY IRON 2), SUPER
QUICK, EXTRA RINSE
DELICATES
40°-Cold
Main wash -...

Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
OptionsDetergent
Compartment
JEANS
60°-Cold
Main wash - Rinses
Maximum spin speed 600 rpm for ZWS 568
Maximum spin speed 800 rpm for ZWS 588
Max. load 3 kg
With this programme it is possible to wash items like pants,
shirts or jackets in denim and also jersey realized with hi-tech
materials. (The Extra Rinse option will be activated automati-
cally).SPIN, RINSE HOLD,
EASY IRON 2)
SPORT...

Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
OptionsDetergent
Compartment
SPIN
Drain and long spin
Maximum spin speed 600 rpm for ZWS 568
Maximum spin speed 800 rpm for ZWS 588
Max. load 6 kg
Separate spin for hand washed garments and after programmes
with the Rinse Hold option selected. You can choose the spin
speed by pressing the relevant button to adapt it to the fabrics
to be spun.SPIN 
O = OFF
For cancelling the programme which...

ProblemPossible cause/Solution
The washing machine does not start:
The door has not been closed (the button 6 red light blinks).
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The programme selector dial is not correctly positioned and the button 6 has
not been pressed.
• Please turn the selector dial...

ProblemPossible cause/Solution
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much foam) has been
used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see if it is
damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The emergency emptying cap has not been...

ProblemPossible cause/Solution
Spinning starts late or the machine
does not spin:
The electronic unbalance detection device has cut in because the laundry is
not evenly distributed in the drum. The laundry is redistributed by reverse
rotation of the drum. This may happen several times before the unbalance
disappears and normal spinning can resume. If, after 10 minutes, the laundry
is still not evenly distributed in the drum, the machine will not spin. In this
case, redistribute the load manually and...

ProgrammeEnergy consumption
(KWh)Water consumption (litres)Programme duration (Mi-
nutes)
Synthetics 40°0.54580
Delicates 40°0.555570
Wool/ Handwash 30°0.35060
1) «Cottons Eco» at 60°C with a load of 6 kg is the reference programme for the data entered in the energy label, in compliance with
EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient...

Place a bowl with a small
edge close to the pump to
collect any spillage.
Pull out the emergency
emptying cap from the fil-
ter cover, using a pliers.
12
When no more water
comes out, unscrew the
pump cover, using a pli-
ers, and remove the filter.
Always keep a rag nearby
to dry up spillage of water
when removing the cover.
Remove any objects from
the pump impeller by ro-
tating it.
Replace the filter into the pump paying attention to in-
sert it properly. When done, screw it firmly.
Replace the...

• Unscrew the hose from the machine. Keep a rag
nearby because some water may flow.
• Clean the filter in the valve with a stiff brush or with
the piece of cloth.
35°
45°
• Screw the hose back to the machine and make sure
the connection is tight.
• Turn on the water tap.
Frost precaution
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
• Turn off the water tap.
• Unscrew the inlet hose.
• Place the end of the inlet hose in a bowl placed on the
floor, open the...

Unscrew the three bolts.Slide out the relevant plas-
tic spacers.
Fill the smaller upper hole and the two large ones with
the corresponding plastic plug caps supplied in the bag
containing the instruction booklet.
Positioning
Install the machine on a flat hard floor. Make sure that air
circulation around the machine is not impeded by carpets,
rugs etc. Check that the machine does not touch the wall
or other kitchen units. Level the washing machine by
raising or lowering the feet. The feet may be tight to...