Zanussi Zws 2101 User Manual

If the temperature and level of the water in the drum
are too high, you cannot open the door.
To open the appliance door:
• Do the steps 1 and 2 again.
• Wait for some minutes.
• Make sure that no water is in the drum.
At the end of the programme
• The appliance stops automatically.
• The start button indicator flashes or the End indicator
is on.
•
Turn the programme knob to 
 to deactivate the ap-
pliance.
• Remove the laundry from the appliance. Make sure that
the drum is empty.
• Keep the door ajar,...

Door seal
Regularly examine the seal
and remove all objects
from the inner part.
Detergent dispenser
To clean the dispenser:
• Press the lever and pull
the dispenser out.
• Remove the top part of
the liquid additive com-
partment.
Clean all the parts with
water.
• Clean the dispenser re-
cess with a brush.
• Put back the dispenser in the recess.
Drain pump
Regularly examine the drain pump and make sure
that it is clean.
Clean the pump if:
• The appliance does not drain the water.
• The drum cannot turn....

6. Remove fluff and ob-
jects from the pump.
7. Make sure that the
impeller of the pump
can turn. If this does
not occur, contact
the service centre.
1 2
8. Clean the filter under
the water tap and put
it back in the pump.
Caution! Make sure
that you tighten cor-
rectly the filter to prevent
leakages.
9. Close the drain pump door.
Clean the inlet valve filter
It could be necessary to clean the filter when:
• The appliance does not fill with water.
• The appliance fills with the water for a long time....

Troubleshooting
The start of the appliance does not occur or it stops dur-
ing operation.
First try to find a solution to the problem (refer to the ta-
ble). If not, contact the service centre.Warning! Deactivate the appliance before you do the
checks.
ProblemPossible causePossible solution
The appliance does not
start.The mains plug is not connected in
the mains socket.Put in the mains plug.
 The fuse in the box fuse is damage.Replace the fuse.
 The appliance door is open.Close the door firmly.
 You do...

ProblemPossible causePossible solution
 The filter of the drain pump is
blocked.Clean the filter of the drain pump. Refer to Care
and cleaning.
 Balance problems with the laundry
load.Adjust manually the items in the tub and start
the spin phase again.
There is water on the floor.Leakages from the couplings of the
water hoses.Make sure that the couplings are tight.
 Leakages from the drain pump.Make sure that the drain pump filter is tight.
 The water drain hose is damaged.Make sure that the water inlet...

Installation
Unpacking
12
A
1. Use the gloves. With a scissor cut the straps and
with a cutter remove the external film.
Do not to discard the plastic cover (A).
2. Remove the polystyrene packaging materials.
3. Remove the internal film.
4. Open the door and remove all the items from the
drum.
16
 
 

5. Put the front piece on the floor behind the appli-
ance. Carefully put down the appliance with the
rear side on it. Make sure not to damage the ho-
ses.
1
2
6. Remove the polystyrene protection from the bot-
tom.
A
7. Install the plastic cover (A), removed from the top
of the packaging, to the bottom of the appliance.
Remove the adhesive strip and close the bottom of
the appliance. Attach permanently the plastic cov-
er to the bottom of the appliance with the small
plastic caps that you can find in...

10. Replace the plastic spacers with the large plastic
caps. You can find these large caps in the user
manual bag.
Warning! Remove all the packaging and the transit
bolts before you install the appliance.
We recommend that you keep the packaging and the
transit bolts for when you move the appliance.
Positioning and levelling
• Install the appliance on a flat hard floor.
• Make sure that carpets do not stop the air circulation
below the appliance.
• Make sure that the appliance does not touch the wall
or...

• On the edge of a sink.
Make sure that the plastic guide cannot move when
the appliance drains. Attach the guide to the water
tap or the wall.
• To a stand pipe with vent-hole.
Refer to the illustration. Directly into a drain pipe at a
height of not less than 60 cm and not more than 90
cm. The end of the drain hose must always be venti-
lated , i.e. the inner diameter of the drainpipe must
be larger than the external diameter of the drain
hose.
Without the plastic hose guide
• To a sink spigot.
Refer to...

 www.zanussi.com/shop
   
155219140-A-202011