Zanussi Zwo 2101 User Manual

4. Press the Start button to start the pro-
gramme until the button indicator is on.
Cancel a programme
1.
Turn the programme knob to 
 to cancel
the programme and to deactivate the appli-
ance.
2. Turn the programme knob again to activate
the appliance. Now, you can set a new
washing programme.
The appliance does not drain the water.
Change a function
You can change only the delay and spin func-
tion before they operate.
Press the related button to set the new value.
Set the delay start
1. Press the...

Care and cleaning
Warning! 
Disconnect the appliance from the mains sup-
ply before you clean it.
External cleaning
Clean the appliance only with soap and warm
water. Fully dry all the surfaces.
Caution! Do not use alcohol, solvents or
chemical products.
Descaling
The water we use contains limescale. If it be-
comes necessary, use a water softener to re-
move limescales.
Use a special product made for washing ma-
chines. Obey the instructions that you find on
the packaging of the manufacturer.
Do this...

Clean the pump if:
• The appliance does not drain the water.
• The drum cannot turn.
• The appliance makes an unusual noise be-
cause of the blockage of the drain pump.
Warning! 
1.Disconnect the mains plug from the mains
socket.
2. Do not remove the filter while the appliance
operates. Do not clean the drain pump if
the water in the appliance is hot. The water
must be cold before you clean the drain
pump.
To clean the drain pump:
1. Open the pump
door.
2. Put a container
below the recess
of the drain...

       
• Clean the filter in the valve with a stiff
brush or a towel.
• Install again the inlet hose. Make sure that
the couplings are tight to prevent leakages.
• Open the water tap.
Emergency drain
Because of a malfunction, the appliance cannot
drain the water.
If this occurs, do steps (1) through (5) of 'To
clean the drain pump'.
If necessary, clean the pump.
When you drain the water with the emergency
drain procedure, you must activate again the
drain system:
1. Put 2 litres of water in the...

ProblemPossible causePossible solution
 The delay start is set.
It is available only for models with
the Delay start.To start immediately the programme, cancel
the delay start.
The appliance does not
fill with water.The water tap is closed.Open the water tap.
 The water inlet hose is damaged.Make sure that the water inlet hose has no
damages.
 The filter in the water inlet hose is
blocked .Clean the filter. Refer to 'Care and cleaning'.
 The water tap is blocked or there
is limescale on it.Clean...

ProblemPossible causePossible solution
The appliance fills with
water and drain immedi-
ately.The end of the drain hose is too
low.Make sure that the drain hose is in the cor-
rect position. Refer to 'Installation'.
The washing results are
not satisfactory.The detergent you used was not
sufficient or correct.Increase the detergent quantity or use a dif-
ferent one.
 You did not remove the stubborn
stains before you wash the laun-
dry.Use special products to remove the stub-
born stains....

2. Remove the polystyrene packaging mate-
rials.
3. Remove the internal film.
4. Open the door and remove all the items
from the drum.
5. Put the front piece on the floor behind
the appliance. Carefully put down the ap-
pliance with the rear side on it. Make
sure not to damage the hoses.
1
2
6. Remove the polystyrene protection from
the bottom.
A
 17 www.zanussi.com
 

7. Install the plastic cover (A), removed from
the top of the packaging, to the bottom
of the appliance. Remove the adhesive
strip and close the bottom of the appli-
ance. Attach permanently the plastic cov-
er to the bottom of the appliance with the
small plastic caps that you can find in the
user manual bag.
8. Pull up the appliance in vertical position.
2
1
9. Remove the four bolts with a key. Pull out
the plastic spacers. Remove the power
supply cable and the drain hose from the
hose holders.
10. Put...

• The appliance must be level and stable.
Caution! Do not put cardboard, wood or
equivalent materials below the appliance
feet to adjust the level.
The inlet hose
• Connect the hose to the appliance. Loose
the ring nut to set it in the correct position.
• Connect the water
inlet hose to the
cold water tap with
3/4 thread.
Caution! Make sure that there are no
leaks from the couplings.
Do not use an extension hose if the inlet
hose is too short. Contact the service cen-
tre for the replacement of the inlet...

• To a sink spigot.
Refer to the illustration. Put the drain hose
in the spigot and tighten it with a clip. Make
sure that the drain hose makes a loop to
prevent that remaining particles go in the
appliance from the sink.• Directly to a built-in drain pipe in the room
wall and tighten it with a clip.
20
 
www.zanussi.com