Zanussi Zwn7120l Manual

							ProblemPossible cause/Solution
Spinning starts late or the
machine does not spin:
The electronic unbalance detection device has cut in because the laundry
is not evenly distributed in the drum. The laundry is redistributed by re-
verse rotation of the drum. This may happen several times before the un-
balance disappears and normal spinning can resume. If, after 10 minutes,
the laundry is still not evenly distributed in the drum, the machine will not
spin. In this case, redistribute the load manually and select the spin pro-
gramme.
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select the
spinning programme.
The machine makes an un-
usual noise:The machine is fitted with a type of motor which makes an unusual noise
compared with other traditional motors. This new motor ensures a softer
start and more even distribution of the laundry in the drum when spinning,
as well as increased stability of the machine.
No water is visible in the
drum:Machines based on modern technology operate very economically using
very little water without affecting performance.
If you are unable to identify or solve the prob-
lem, contact our service centre. Before tele-
phoning, make a note of the model, serial num-
ber and purchase date of your machine: the
Service Centre will require this information.
Mod. ... ... ...
Prod. No. ... ... ...
           Ser. No. ... ... ...
Mod. .
.
.
 ... .
..
Prod. No.
 ...
 ... ..
  
   
    
  
  
  
     
    
 S
er.  N o
. ... ... ...
Technical data
DimensionsWidth
Height
Depth60 cm
85 cm
63 cm
Electrical connectionInformation on the electrical connection is given on the rating plate, on
the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton8 kg
Spin SpeedMaximum1000 rpm (ZWN7100L)
1200 rpm (ZWN7120L)
Consumption values
The data of this table are approximate. Different causes can change the data: the quantity and
type of laundry, the water and ambient temperature.
 21 www.zanussi.com 
						

							ProgrammesLoad
(kg)Energy con-
sumption
(kWh)Water con-
sumption (li-
tre)Approxi-
mate pro-
gramme
duration
(minutes)Remaining
moisture
(%)
1)
ZWN7100L
Remaining
moisture
(%)
1)
ZWN7120L
Cottons 60 °C81.4631606053
Cottons 40 °C80.6631306053
Synthetics 40
°C3,50.654803735
Delicates 40 °C30.663653735
Wool/Hand
wash 30 °C20.2555603230
Standard cotton programmes
Standard 60 °C
cotton81.17612056053
Standard 60 °C
cotton40.77491596053
Standard 40 °C
cotton40.7481616053
1) At the end of spin phase.
Off Mode (W)Left On Mode (W)
0.100.98
The information given in the charts above are in compliance with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC.
Installation
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever has
to be transported again.
After removing all the
packaging, carefully
lay machine on it's
back to remove the
polystyrene base from
the bottom.Remove the power
supply cable and the
hose from the hose
holders on the rear of
the appliance.
22
 
www.zanussi.com 
						

							Unscrew the three
bolts.Slide out the relevant
plastic spacers.
Open the porthole,
remove the polystyr-
ene block fitted on
the door seal and pull
out all items from the
drum.Fill the smaller upper
hole and the two
large ones with the
corresponding plastic
plug caps supplied in
the bag containing
the instruction book-
let.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units. Level the washing machine by
raising or lowering the feet. The feet may be
tight to adjust as they incorporate a self locking
nut, but the machine MUST be level and stable.
Any necessary adjustment can be made with a
spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Never place cardboard, wood or similar materi-
als under the machine to compensate for any
unevenness in the floor.
If necessary, check
the setting with a spi-
rit level.
Rubber feet kit (4055126249)
Available from your authorized dealer.
The rubber feet are particularly recommended
on floating, slippery and wooden floors.
Mount the rubber feet to prevent vibration,
noises and displacement of the appliance dur-
ing operation.
Read carefully the instructions supplied with the
kit.
Water inlet
Warning! This appliance must be
connected to a cold water supply
Caution! Before connecting up the
appliance to new pipework or to pipework
that has not been used for some time, run off a
reasonable amount of water to flush out any
debris that may have collected
Caution! Do not use the hose from your
previous appliance to connect to water
supply.
Connect the hose to
a tap with a 3/4”
thread. Always use
the hose supplied
with the appliance.
 23 www.zanussi.com 
						

							35°
45°
The other end of the inlet hose which con-
nects to the appliance can be turned as
showed in the picture.
Do not place the inlet hose downwards.
Angle the hose to the left or right depending
on the position of your water tap. Set the hose
correctly by loosening the ring nut. After posi-
tioning the inlet hose, be sure to tighten the
ring nut again to prevent leaks.
Caution! The inlet hose must not be
lengthened. If it is too short and you do not
wish to move the tap, you will have to purchase
a new, longer hose specially designed for this
type of use.
Water drainage
The end of the drain hose can be positioned in
three ways:
Hooked over the
edge of a sink us-
ing the plastic
hose guide.
In this case, make sure the end cannot come
unhooked when the machine is emptying. This
could be done by tying it to the tap with a
piece of string or attaching it to the wall.
In a sink drain pipe branch. This branch
must be above the trap so that the bend is at
least 60 cm above the ground.
Directly into a drain pipe at a height of
not less than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the
drain pipe must be larger than the outside di-
ameter of the drain hose. The drain hose must
not be kinked.
Environmental concerns
The symbol  on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help preventpotential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
24
 
www.zanussi.com 
						

							Packaging materials
The materials marked with the symbol 
 are re-
cyclable.
>PEPSPP
						

							26
 www.zanussi.com 
						

							 27 www.zanussi.com 
						

							 www.zanussi.com/shop
   
192986482-A-512012