Zanussi Zwi 1125 User Manual

							SHOWER
WASHING
MACHINEDISHWASHER BATHSINKTOILET
BIDET
RAINWATER
‘RUN-OFF’
SURFACE WATER
DRAINS & SEWERS
UNTREATED
DISCHARGE
RIVER RIVERTREATED DISCHARGEFOUL DRAIN
FOUL SEWERS
SEWAGE TREATMENT
WORKS
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or compe-
tent person.
Warning! THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should this
safety measure not be observed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate.
Warning! Information on the electrical connection is
given on the rating plate on the inner edge of the
appliance door.
The appliance is supplied with a 13 amp plug fitted.
In the event of having to change the fuse in the plug sup-
plied, a 13 amp ASTA approved (BS1363/A) fuse must be
used.
Warning! A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of safely. Should
the appliance power supply cable need to be replaced, this
MUST be carried out by our Service Force Centre. The
appliance should not be connected to the electrical supply
by means of an extension cable.
Note!
When the appliance is installed the power supply cable
must be accessible.
Building in
This appliance has been designed to be built into the
kitchen furniture. The recess should have the dimensions
shown in picture A.
 21
 
						

							A
600
596 555
170 75176,5
416
100 60818 min.
820min.
560
When installing the appliance into the kitchen furniture
ensure, if possible, the hoses are placed in either of the
two recesses on the back of the appliance.
This will help to prevent the hoses from becoming
kinked or trapped.
B
1
23
75
6
4
8
Caution! Do not remove the screw 8!
Preparation and assembly of the door
The machine is originally prearranged for the assembly
of a door opening from right to left.
In this case it is sufficient to screw in the hinges (1) and
the counter-magnet (6) provided with the appliance, at
the right level (Fig. B).
C
16-22
595-59822±1,5 416 B
C 35 Ø 12,5-14 depth
•a) Door
The dimensions of the door should be:
- width 595-598 mm
- thickness 16-22 mm
The height (C-Fig. C) depends on the height of the ad-
jacent furnitures base.
•b) Hinges
To mount the hinges it is necessary to drill two holes
(dia. 35 mm, depth 12.5-14 mm depending on the
depth of door furniture) on the inner side of the door.
The distance between the holes hobs fixing centres
must be 416 mm.
The distance (B) from upper edge of the door to the
centre of the hole depends on the adjacent furnitures
dimensions.
The required dimensions are given in the picture C.
The hinges will be fixed to the door by means of screws
for wood (2-Fig. B) supplied with the appliance.
•c) Mounting the door
Fix the hinges (1) to the machine by means of the M
5x15 screws (3-Fig. B). The hinges can be adjusted to
compensate for possible uneven thickness of the door.
To align the door perfectly it is necessary to loosen the
screw (3-Fig. B), adjust the door and tighten the screw
again.
22
 
 
						

							D
4
6
8
Caution! Do not remove the screw 8!
d) Counter-magnet (6)
The appliance is prearranged for a magnetic closure of
the door.
To enable a correct operation of this device, it is neces-
sary to screw the counter-magnet (6) (steel disk + rub-
ber ring) into the inner side of the door. Its position
must correspond to the magnet (4) on the appliance
(see picture D).
E
1
2 3
75
6
4
8
Caution! Do not remove the screw 8!
If the door has to be opened from left to right, invert the
position of the plates (7), the magnet (4) and the plate
(5) (Fig. B and E). Mount the counter-magnet (6) and
the hinges (1) as previously described.
Recommendations regarding the construction and fit-
ting of a base when the installation requires an integra-
ted appliance to be raised.
Graphic F
Front view
5 mm Hardwood strip
Additional pieces
of timber should run
from front to back
40
600-605 100
Where the appliance has been raised by mounting onto
a wooden base provided by the installer. The material
used to construct the base should have anon slip sur-
face, be water repellent and if possible be one solid
piece.
If it is not possible to use one solid piece, due to the
additional height required, ensure that any additional
strips of timber are glued and screwed to the underside
of the base (see Fig. F).
Graphic G
Top view
Front edge
600-605
490
95
50
 23
 
						

							Drill four fixing holes see Fig. G
Position the base into the recess with its front edge as
far forward as the adjoining plinth line will allow.
The reason for placing the base in this position is to al-
low a small strip of beading to be fitted in front of the
appliance feet.
Graphic H
600-605 4905 x 25 x 605
Hardwood strip
5 mm x 25 mm
Fix the base firmly to the floor using four appropriate
countersunk screws (see Fig. H).
With the appliance installed adjust all four feet ensuring
the machine is stable, and a clearance of approximately
5 mm is left between the top of the machine and the un-
derside of the worktop.
A final check for stability should be carried out with the
machine on spin with a load, this will identify the need
for any further fine adjustment to the feet.
A strip of beading approximately 605 mm W, x 5 mm H,
x 25 mm D must be screwed down into the base directly
in front of the machine’s feet, this will provide addition-
al security.
If required an additional door magnet, part number
1242394-00/3 and disc, part number 1242393-00/5 are
available from spare parts.
Environmental concerns
The symbol  on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed
information about recycling of this product, please contact
your local council, your household waste disposal service
or the shop where you purchased the product.
Packaging materials
The materials marked with the symbol  are recyclable.
>PEPSPP
						

							 25
 
						

							26
 
 
						

							 27
 
						

							 www.zanussi.com/shop
   
132966891-A-462011