Zanussi Zwh 6125 User Manual

Personalisation
Acoustic signals
The machine is provided with an acoustic device, which
sounds in the following cases:
• at the end of the cycle
• if there is a fault.
By pressing the 4 and 5 buttons simultaneously for about
6 seconds , the acoustic signal is deactivated (except if
there is a fault). By pressing these 2 buttons again, the
acoustic signal is reactivated.
Child safety lock
This device permits you to leave the appliance unattended
and not to worry that children might be injured by or cause...

When these buttons are pressed, the corresponding pilot
lights illuminate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected, the inte-
grated red pilot light of the button 7 flashes 3 times and
the message Err is displayed.
For the compatibility among the washing programmes
and the options see chapter «Washing programmes» .
Start the programme by pressing button 7
To start the selected programme, press this button; the
corresponding green pilot light stops...

1.
Turn the programme selector dial to  .
2. Select the draining or spinning programme.
3. Reduce the spin speed if needed, by pressing the
relevant button.
4. Press button 7 .
At the end of the programme, the door is released and can
be opened. Turn the programme selector dial to 
 to
switch the machine off.
Remove the laundry from the drum and carefully check
that the drum is empty. If you do not intend to carry out
another wash, close the water tap. Leave the door open to
prevent the formation of...

Pull out the emergency
emptying hose, place it in
the container and remove
its cap.
When no more water comes out, unscrew the pump
cover and remove it. Always keep a rag nearby to dry
up spillage of water when removing the cover.
Remove any objects from
the pump impeller by ro-
tating it.
Put the cap back on the
emergency emptying hose
and place the latter back in
its seat.
Screw the pump cover
fully in.
Close the pump door.
Caution!  When the appliance is in use and
depending on the programme selected...

• When you intend to start the machine up again, make
sure that the room temperature is above 0°C.
Emergency emptying out
If the water is not discharged, proceed as follows to empty
out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove its
cap. The water should drain by gravity into the bowl.
When the...

ProblemPossible cause/Solution
The machine does not fill:
The water tap is closed. 
• Open the water tap.
The inlet hose is squashed or kinked. 
• Check the inlet hose connection.
The filter in the inlet hose is blocked. 
• Clean the water inlet hose filter.
The door is not properly closed. 
• Close the door firmly.
The machine does not empty and/or
does not spin:
The drain hose is squashed or kinked. 
• Check the drain hose connection.
The drain filter is clogged. 
• Clean the drain filter.
An option or...

ProblemPossible cause/Solution
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the pilot light 9  goes off.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance....

Technical data
DimensionsWidth
Height
Depth60 cm
85 cm
63 cm
Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating plate, on the
inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton7 kg
Spin SpeedMaximum1200 rpm
Consumption values
ProgrammeEnergy consumption
(KWh)Water consumption (litres)Programme duration (Mi-
nutes)
White Cottons 90°2.165
For the duration of the pro-
grammes, please refer...

After removing all the
packaging, carefully lay
machine on its back to re-
move the polystyrene base
from the bottom.Remove the power supply
cable and the hoses from
the hose holders on the
rear of the appliance.
Unscrew the three bolts.Slide out the relevant plas-
tic spacers.
Open the porthole and re-
move the polystyrene
block fitted on the door
seal.Fill the smaller upper hole
and the two large ones
with the corresponding
plastic plug caps supplied
in the bag containing the
instruction booklet....

The other end of the inlet hose which connects to the
appliance can be turned as showed in the picture.
Do not place the inlet hose downwards. Angle the hose
to the left or right depending on the position of your
water tap. Set the hose correctly by loosening the ring
nut. After positioning the inlet hose, be sure to tighten
the ring nut again to prevent leaks.
Caution!  The inlet hose must not be lengthened. If
it is too short and you do not wish to move the tap,
you will have to purchase a new, longer...