Zanussi Zwg 7160 P Manual

							Programme - Maximum and Minimum Temperature - Cycle De-
scription - Maximum Spin Speed - Maximum Fabrics Load - Type
of Laundry
OptionsDetergent Com-
partment
JEANS
60°- Cold
Main wash - Rinses - Maximum spin speed at 900 rpm
Max. load 3 kg
Trousers, shirts or jackets in denim and jersey realized with hi-tech
materials. The Extra Rinse option is activated automatically.
SPIN REDUCTION
RINSE HOLD
DELAY START
1) If you select the SUPER QUICK option by pressing button 5, we recommend that you reduce the maximum load as indicated. Full
loading is possible however with somewhat reduced cleaning results.
2) In case of prewash phase, put the detergent directly into the drum.
Consumption values
Programme1)Energy consumption (KWh)2)Water consumption (litre)2)
White Cottons 90 °C2.178
Cottons 60 °C1.272
Cottons 40 °C0.7572
Synthetics 40 °C0.657
Delicates 40 °C0.665
Wool/ Handwash 30 °C0.348
1) Refer to the display for the programme time.
2) The consumption information shown in this chart is indicative. It can vary depending on the quantity and the type of laundry, on the
temperature of the water supply and on the ambient temperature.
Standard programmes for the Energy Label consumption
values
The cotton 60 °C economy and cotton 40 °C economy are
the standard cotton programmes for normally soiled cot-
ton laundry. They are suitable to clean normally soiled
cotton laundry and they are the most efficient programmesin terms of combined energy and water consumption for
washing that type of cotton laundry.
They agree with EN60456.
The actual water temperature may differ from the de-
clared cycle temperature.
Care and cleaning
Warning! Switch the appliance off and remove the
mains plug from the socket before any cleaning
action.
Maintenance Wash
With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed on
a regular basis.
To run a maintenance wash:
• The drum should be empty of laundry.
• Select the hottest cotton wash programme.
• Use a normal measure of detergent, must be a powder
with biological properties.
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
 21 
						

							• Remove the drawer.
• To aid cleaning, the top
part of the additive
compartment should be
removed.
• Use a stiff brush to clean and remove all washing
powder residue.
• Clean all the removed parts of the dispenser drawer
under a tap to remove any traces of accumulated
powder.
• Use the previous brush
to clean the recess, en-
suring that upper and
lower part of it is well
cleaned.
After having cleaned the dispenser and the drawer re-
cess, replace it.
Cleaning the drain filter
The filter permits to hold fluff or foreign bodies left un-
awares in the laundry.
The pump must be cleaned regularly.
To clean the filter, proceed as follows:
•
turn programme selector dial to position 
 ;
• unplug the appliance;
• open the door;
• turn the drum and align
the filter cover (FILTER)
with the arrow on the
door seal;
• open the filter cover by
pressing the special
hook and by rotating
the cover upwards;
Warning! Keep the
filter cover open un-
til the filter removal.
• before removing the fil-
ter, remove any fluff or
small objects from
around the filter;
• remove the filter and clean it under the tap;
22
  
						

							• if necessary, place the
filter cover in the right
position again.
• open the filter cover
and insert the filter
again;
The filter is inserted correctly when the indicator on its
top is visible and blocked.
• close the filter cover;
• insert the mains plug
again.
Cleaning the water inlet filters
Important! If the appliance doesnt fill, it takes a long time
to fill with water, the starting button flashes red or the
display (if available) shows the relevant alarm (see chapter
What to do if... for more details), check if the water inlet
filters are blocked .
To clean the water inlet filters:
• Turn off the water tap.
• Unscrew the hose from
the tap.
• Clean the filter in the
hose with a stiff brush.
• Screw the hose back onto the tap. Make sure the
connection is tight.
• Unscrew the hose from
the appliance. Keep a
towel nearby because
some water may flow.
• Clean the filter in the
valve with a stiff brush
or with the piece of
cloth.
• Screw the hose back to the appliance and make sure
the connection is tight.
• Turn on the water tap.
What to do if…
The appliance does not start or stops during operation.
Certain problems are due to lack of simple maintenance or
oversights, which can be solved with the help of the indi-
cations described in the charts, without calling out an en-
gineer.
During appliance operation it is possible that the red pilot
light of the button 9 flashes, the display shows a faultcode and the buzzer sounds to indicate that the appliance
is not working.
Before contacting your local Service Centre, please carry
out the checks listed below.
 23 
						

							Fault code and malfunctionPossible cause / Solution
Problem with the water supply
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked.
• Clean the water inlet filters (read Cleaning the water inlet filters for more details).
Problem with the water drain-
age
The drain hose is squashed or kinked.
• Check the drain hose connection.
The drain filter is clogged.
If the appliance stops working without discharging the water , first carry out an emer-
gency drain:
•
turn the programme selector dial to 
 ;
• unplug the appliance;
• close the water tap;
• if necessary, wait until the water has cooled down;
• unscrew the drain hose from the rear support (see Frost precaution) and unhook
it from the sink or spigot;
• let it run along the floor;
• place a bowl on the floor and place the end of the draining hose into the bowl. The
water should drain by gravity into the bowl. When the bowl is full, empty it. Repeat
the procedure until water stops flowing out ;
• screw the draining hose to the rear support and reposition it;
• open the door and remove the laundry;
• carry out the drain filter cleaning as described in Cleaning the drain filter;
• at the end of cleaning action, close the door and insert the mains plug again;
• run a drain programme to check if the appliance works now.
Door open
The door has not been closed or is not closed properly.
• Close firmly the door.
The appliance does not start or stops during operation
without any visible alarm.Before contacting your local Service Centre, please carry
out the checks listed below.
24
  
						

							MalfunctionPossible cause / Solution
The appliance does not start:
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The programme selector dial is not correctly positioned and the button 9 has not been
pressed.
• Please turn the selector dial and press the button 9 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The Child Safety Lock has been activated.
• Deactivate the Child Safety Lock.
The appliance fills then emp-
ties immediately:The end of the drain hose is too low.
• Refer to paragraph in Water drainage in chapter Installation.
The appliance does not empty
and/or does not spin:
An option or a programme that ends with the water still in the tub or a that eliminates
all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is not always
easy to see this as the water runs down the hose; check to see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the door lock is released.
Open the door when the pilot light 10 is off.
There is water in the drum.
• Select drain or spin programme to empty out the water.
 25 
						

							MalfunctionPossible cause / Solution
The appliance vibrates noisi-
ly:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The appliance is not levelled correctly.
• Adjust the feet.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
Spinning starts late or the ap-
pliance does not spin:
The electronic unbalance detection device has cut in because the laundry is not even-
ly distributed in the drum. The laundry is redistributed by reverse rotation of the
drum. This may happen several times before the unbalance disappears and normal
spinning can resume. If, after 10 minutes, the laundry is still not evenly distributed in
the drum, the appliance will not spin. In this case, redistribute the load manually and
select the spin programme.
• Load more laundry.
The load is too small.
• Add more items, redistribute the load manually and then select the spinning pro-
gramme.
No water is visible in the
drum:Appliances based on modern technology operate very economically using very little
water without affecting performance.
Unsatisfactory washing re-
sults
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The appliance makes an un-
usual noise
The appliance is fitted with a type of motor which makes an unusual noise compared
with other traditional motors. This new motor ensures a softer start and more even
distribution of the laundry in the drum when spinning, as well as increased stability of
the appliance.
After completing these checks, switch on the appliance
and press the button 9 to restart the programme.If the malfunction shows again, contact your Service Cen-
tre. The necessary data for the service centre is on the rat-
ing plate. We recommend that you write the data here:
26
  
						

							Mod. ... ... ...
Prod. No. ... ... ...
           Ser. No. ... ... ...
Mod. ..
. ... ...
Pr
od. No
.
 ... ... ..
  
   
    
  
  
  
     
    
 S
er
. N
o
. ... 
... 
...
Model description (MOD.) ...............................
Product number (PNC) ...................................
Serial number (S.N.) .......................................
 27 
						

							 www.zanussi.com/shop
   
192987490-A-092011