Zanussi Zwg 6105 User Manual

							50
Consumption values
Programme
duration 
(in minutes)Programme Energy
consumption 
(in kWh)Water
consumption 
(in litres)
125Cottons 95°C2.061
ZWG6105-ZWG 5125....155
ZWF6115 .......................125Cottons 60° Eco(*)ZWG6105-ZWG 5125...1.02
ZWF6115 ......................0.85ZWG6105-ZWG 5125......54
ZWF6115 .........................52
100Cottons 60°C - 40°C1.358
145Cottons 40°C Eco1.1454
55 Delicates 40º - Cold 0.5560
60Handwash 30º - Cold0.453
45Rinse0.142
10Spin--
2Drain--
80Synthetics 60º C - Cold0.851
Infos
The consumption data shown on this chart is
to be considered purely indicative, as it may
vary depending on the quantity and type of
laundry, on the inlet water temperature and on
the ambient temperature. It refers to the
highest temperature for each wash
programme.
(*) The “Cottons 60° Eco” is the reference
programme for the data entered in the
energy label, in compliance with EEC
92/75 standards.
126.2936.33…ZWF615.qxd  15/5/08  11:44  Página 50
 
						

							51
Installation instruction
Transit security bars
Before starting the machine up, the transport
security  bars must be removed as follows:
You are advised to keep all the transport
security bars. In case the appliance has to be
transported again.
1. Unscrew and remove the three rear screws
by means of a key.
2. Open the porthole and remove the
polystyrene block fitted with adhesive tape
on the door seal.
3. Place the machine in an upright position
and remove the three plastic bolts.
4. Plug the 3 holes with the plastic plugs
which you can find in the envelope
containing the instruction booklet.Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units. Level the washing machine by
raising or lowering the feet. Once in the right
position fix the feet by pushing the nuts
against the base of the case. The feet may be
tight to adjust as they incorporate but the
machine MUST be level and stable.
If necessary, check the setting with a spirit
level.
Accurate levelling prevents vibration, noise
and displacement of the machine during
operation.Never place cardboard, wood or
similar materials under the machine to
compensate for any unevenness in the floor.
Some vibration is inevitable, especially if
mounted on a wooden floor.
Sprung wooden floors are particularly
susceptible to vibration. For advice, consult a
builder. If possible, always place the machine
on a solid floor.
126.2936.33…ZWF615.qxd  15/5/08  11:44  Página 51
 
						

							52
Water inlet
There should be a COLD WATER tap near the
washing machine with a screwing on
connection pipe of 3/4" for the water supply, a
sink, a wash basin or a drainage system in the
wall.
Previously check if:
- it is not a hot water tap.
- the running water is clean. If not, run off a
reasonable amount of water to flush out any
debris that may have collected in the pipes.
Have the permanent drainage system in the
wall checked by a plumber.
1. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied with
the appliance. The inlet hose must not be
lengthened. If it is too short and you do not
wish to move the tap, you will have to
purchase a new, longer hose specially
designed for this type of use.
NOTE
Installation should
comply with local
water authority and
building regulations’
requirements.
2. If necessary turn the hose adequately by
unscrewing the nut at the rear of the
appliance. Now tighten the nut anew to
avoid leaks. (Open the tap and assure that
it does not leak and close it again.)
The appliance must be connected to a cold
water supply. 
A minimum water pressure of 0.05 MPa (0.5
bar) is required for safe operation of the
appliance.
If you cannot make the cold water connection
direct from the rising mains, you may be able
to operate the appliance from your cold water
storage system.
There should be a minimum distance of
5.02m (16.5 ft) between the appliance’s inlet
and the bottom of the water storage tank.
Water drainage
This appliance is designed to be permanently
plumbed into your home's drainage system
using one of the following methods.
1.  Into a drainage standpipe.
Firstly form a hook in the end of the drain
hose using the «U» piece supplied. Place the
drain hose into your standpipe, which should
have an internal diameter of approximately
38mm thus ensuring there is an air break
between the drain hose and standpipe.
When discharging into a standpipe ensure
that the top of the standpipe is no more than
90 cm (35.4'') and no less than 60 cm (23.6'')
above floor level.



126.2936.33…ZWF615.qxd  15/5/08  11:44  Página 52
 
						

							53
The drain hose may be extended to a
maximum of 4 metres. An additional drain
hose and joining piece is available from your
local Service Force Centre. The joining piece
must have an internal diameter of 18mm.
If your drain hose
looks like this (see
below) you do not
require the «U»
piece. Just push the
hose firmly into the
standpipe.
2. Onto a sink outlet spigot.
If the outlet spigot has not been used before,
remove any blanking plug that may be in
place.
Push the drain hose onto the spigot and
secure with a clip if required, ensure a loop is
formed in the drain hose (see diagram) to
prevent waste from the sink entering the
washing machine.
Important!
Before connecting the machine to new
pipework or to pipework that has not been
used for some time, run off a reasonable
amount of water to flush out any debris that
may have collected in the pipes.


Special conditions
If the floor is carpeted or covered with crumbly
or soft material, insert a rigid support base
under the feet to prevent noise, vibration or
displacement. The base should protrude a few
centimetres beyond the edges of the machine.
WARNING!
The machine should NOT be placed on deep
pile carpeting.
NOTE
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of a breakdown.
In the interest of the environment
Washing machines and dishwashers should
be connected to the FOUL drainage system,
the water will then be taken to a sewage
works for treatment before being discharged
safely into a river. It is essential that these
appliances are not connected to the surface
water drainage system as this water is
discharged directly into a river or stream and
may cause pollution.
If you require any further advice please
contact your local water authority.

 





 !!
!






#!

!




# 

126.2936.33…ZWF615.qxd  15/5/08  11:44  Página 53
 
						

							54
Electrical connection
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
WARNING!
This appliance must be earthed.
The manufacturer declines any liability
should this safety measure not be
observed.
Before switching on, make sure the electricity
supply voltage is the same as that indicated
on the appliance’s rating plate. 
IMPORTANT!
Information on the electrical connection is
given on the rating plate on the inner edge
of the appliance door.
The appliance is supplied with a 13amp plug
fitted. In the event of having to change the
fuse in the plug supplied, a 13amp ASTA
approved (BS1363/A) fuse must be used.
Should the plug need to be replaced for any
reason, proceed as described below.
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow ..............................- Earth
Blue ....................................................- Neutral
Brown..................................................- Live
The wire coloured
green and yellow
must be connected to
the terminal marked
with the letter «E» or
by the earth symbol
or coloured green
and yellow.
The wire coloured blue must be connected to
the terminal marked «N» or coloured black.
	 
	
  
 


The wire coloured brown must be connected
to the terminal marked «L» or coloured red.
Upon completion there must be no cut, or
stray strands of wire present and the cord
clamp must be secure over the outer sheath.
WARNING!
A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely. Should the appliance power supply
cable need to be replaced, this must be
carried out by our Service Force Centre.
The power supply cable must be easily
accessible after installing the appliance.
Permanent connection
In the case of permanent connection it is
necessary that you install a double pole switch
between the appliance and the electricity
supply (mains), with a minimum gap of 3mm
between the switch contacts and of a type
suitable for the required load in compliance
with the current electrical regulations.
The switch must not break the yellow and
green earth cable at any point.
126.2936.33…ZWF615.qxd  15/5/08  11:44  Página 54
 
						

							55
Environmental concerns
Packaging materials
The materials marked with the symbol  are
recyclable.
>PEPSPP
						

							56
Guarantee conditions
Standard guarantee conditions
We, Electrolux, undertake that if within 12
months of the date of the purchase this
Electrolux appliance or any part thereof is
proved to be defective
by reason only of faulty workmanship or
materials, we will, at our option repair or
replace the same FREE OF CHARGE for
labour, materials or carriage on condition that:
●The appliance has been correctly installed
and used only on the electricity supply
stated on the rating plate.
●The appliance has been used for normal
domestic purposes only, and in accordance
with the manufacturer’s instructions.
●The appliance has not been serviced,
maintained, repaired, taken apart or
tampered with by any person not authorised
by us.
●Electrolux Service Force Centre must
undertake all service work under this
guarantee
●Any appliance or defective part replaced
shall become the Company’s property.
●This guarantee is in addition to your
statutory and other legal rights.
Exclusions
●Damage or calls resulting from
transportation, improper use or neglect, the
replacement of any light bulbs or removable
parts of glass or plastic.
●Costs incurred for calls to put right an
appliance which is improperly installed or
calls to appliances outside the United
Kingdom.
●Appliances found to be in use within a
commercial environment, plus those which
are subject to rental agreements.
●Products of Electrolux manufacturer that are
not marketed by Electrolux.
European Guarantee
This appliance is guaranteed by Electrolux in
each of the countries listed at the back of this
user manual, for the period specified in the
appliance
guarantee or otherwise by law. If you move from
one of these countries to another of the
countries listed below the appliance guarantee
will move
with you subject to the following qualifications:
●The appliance guarantee starts from the date
you first purchased the appliance which will
be evidenced by production of a valid
purchase document issued by the seller of
the appliance.
●The appliance guarantee is for the same
period and to the same extent for labour and
parts as exists in your new country of
residence for this particular model or range of
appliances.
●The appliance guarantee is personal to the
original purchaser of the appliance and
cannot be transferred to another user.
●The appliance is installed and used in
accordance with instructions issued by
Electrolux and is only used within the home,
i.e. is not used for commercial purposes.
●The appliance is installed in accordance with
all relevant regulations in force within your
new country of residence.
The provisions of this European Guarantee do
not affect any of the rights granted to you by
law."
126.2936.33…ZWF615.qxd  15/5/08  11:44  Página 56
 
						

							57
www.electrolux.com
126.2936.33…ZWF615.qxd  15/5/08  11:44  Página 57
 
						

							126.2936.33
www.electrolux.com
126.2936.33…ZWF615.qxd  15/5/08  11:44  Página 60