Zanussi Zwg 1120 M User Manual

Load the laundry 
Measure out the detergent and the fabric softener 
Select the required programme by means of the 
programme selector dial (3) 
Important! 
Select the spin speed by pressing button 7 
Select the available options by pressing buttons 2Open the door by 
carefully pulling the door
handle outwards. Place
the laundry in the drum,
one item at a time,
shaking them out as much
as possible. Close the
door.
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent required,...

Cancelling the Delay Start after having started the 
programme:
1. Set the washing machine to PAUSE by pressing 
button .
2. Press button repeatedly until the display shows 0.
3. Press button again to start the programme. The door will be locked throughout the delay time.
If you need to open the door, you must first set the 
washing machine to PAUSE by pressing button 
and wait a few minutes before opening the door.
After you have closed the door, press the same
button again.
The Delay Start cannot be...

Care and cleaning
ZANUSSI
1 3
Warning!
Descaling 
External cleaning 
Cleaning the dispenser drawer 
Cleaning the drawer recess You must DISCONNECT the appliance
from the electricity supply, before you can carry
out any cleaning or maintenance work. 
The water we use normally contains lime. It is a good 
idea to periodically use a water softening powder in
the machine.
Do this separately from any laundry washing, and
according to the softening powder manufacturers
instructions.
This will help to prevent...

1 4
If you wash rugs, it is compulsory to inspect and 
clean the filter. 
Cleaning the water inlet filters 
Important! 
If the appliance doesnt fill, takes long to fill with water,
the starting button blinks yellow or the display (if
available) shows the relevant alarm (see chapter
«What to do if...» for more details), check if the water
inlet filters are blocked.
To clean the water inlet filters:Turn off the water tap.
 Unscrew the hose
from the tap. Clean the filter in the
hose with a stiff brush.
...

1 5
ZANUSSI
What to do if.....
Certain problems are due to lack of simple 
maintenance or oversights, which can be solved
easily without calling out an engineer.Before contacting your local Service Centre, please
carry out the checks listed below.
MalfunctionPossible Cause / Solution
The washing  machine does not work Close the washing machines door.
Water leakage
Correctly connect  the inlet  water pipe.
The spin of the clothes  is abnormalReload  and distribute the laundry evenly in the drum.
There is...

1 6
MalfunctionPossible Cause / Solution
The machine stops when the proce- 
dure has not been finishedPower  failure or water cut.
The water inside the inner barrel  has been drained 
but there is still a small amount of water in the
drainage pump and pipe. The drainage pump
continuously work and takes in the air, then  there
wil be noise which is normal situation.
The machine stops for some time 
during the wash procedure.
The washing machine adds water automatically.
There is too much foam in the tube,...

1 7
ZANUSSI
If you are unable to identify or solve the problem, 
contact our service centre. Before telephoning, make
a note of the model, serial number and purchase date
of your machine. The Service Centre will require this
information.
Technical data
9 4 8 m m4 9 5 m m
8 5 5 m m
5 9 5 m m
Rated Mains2  0-240 V2 / 50Hz
Water pressure
0.02MPa~1MPa
Net weight
65Kg 6Kg 
1400   (ZWG1140M) 
1200   (ZWG1120M)
1000   (ZWG1100M)
Drain method
Upper drain
Spin method 
Washing capacity
Maxinum spin speed rpm...

Installation
1 8
Unpacking 
Positioning
All transit bolts and packing must be removed before 
using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
Unscrew the four boltsusing a spanner.
Slide out the relevant
plastic spacers.
Fill the holes with the corresponding plastic
plug caps supplied in the
bag containing the
instruction booklet.
Install the machine on a flat hard floor. Make sure that air
circulation around...

1 9
ZANUSSI
Caution! 
Water drainageHooked over the edge 
of a sink
The inlet hose must not be lengthened. If it
is too short and you do not wish to move the tap, you 
will have to purchase a new, longer hose specially
designed for this type of use. 
The end of the drain hose can be positioned in three 
ways:
using the
plastic hose guide
supplied with the
machine.
In this case, make sure
the end cannot come
unhooked when the
machine is emptying. 
This could be done by
tying it to the tap with a piece of...

ZANUSSI
w w w. e l e c t r o l u x . c o mw w w. z a n u s s i . b e
S u b j e c t t o c h a n g e w i t h o u t n o t i c e