Zanussi Zwf 385 User Manual

							21
If you are unable to identify or solve the
problem, contact our service centre. 
Before telephoning, make a note of the model,
serial number and purchase date of your
machine: the Service Centre will require this
information.
Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
M
o
d
.
 
.
..
 
..
.
 
.
.
.
P
r
o
d
.
 
N
o
. 
.
..
 
..
.
 
.
.
 
 
  
 
  
 
  
 
  
 
  
 
  
 
  
 
  
S
e
r
.
 
No
.
 
..
.
 
.
.
. 
.
..
Technical data
Dimensions Width 60 cm
85 cm
63 cm Height
Depth (including the porthole)
Water supply pressure Minimum 0,05 MPa
0,8 MPa Maximum
Cotton Maximum Load 5 kg
Maximum Spin Speed0800 rpm Electrical connection Voltage -
Overall power - FuseInformation on the electrical connection is given on the rating
plate on the inner edge of the appliance door
132970080gb.qxd  13/02/2008  13.44  Page 21
 
						

							Infos
The consumption data shown on this chart is
to be considered purely indicative, as it may
vary depending on the quantity and type of
laundry, on the inlet water temperature and on
the ambient temperature. It refers to the
highest temperature for each wash
programme.(*) The «Cotton Eco» at 60°C with a load of 5
kg is the reference programme for the data
entered in the energy label, in compliance
with EEC 92/75 standards.
Consumption values
Programme
duration Programme Energy
consumption 
(in kWh)Water
consumption 
(in litres)
Cotton 95°1.958
Cotton 95° + Prewash2.0568
Eco 60° (*)0.8549
Synthetics 60°
1.0559
Synthetics 60° +  Prewash
0.7545
0.557
Handwash 40°0.453
Jeans 40°0.554
Sport 40°0.657
Spin--
Rinse0.0742
Drain--
0.95
Eco 60° + Prewash
60
0.770
135
155
130
150
85
65
55
11 0
90
10
45
2
100
80
Delicates 40°
Delicate + Prewash 40°
22
132970080gb.qxd  13/02/2008  13.44  Page 22
 
						

							23
Installation instruction
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom. 
2. Remove the power supply cable and the
draining hose from the hose holders on the
rear of the appliance.
3. With a suitable spanner unscrew and
remove the central rear bolt A.
4. Unscrew and remove the two large rear
bolts Band the six smaller bolts C.



D
CC
B
B
	
5. Remove the bracket D, refit the six smaller
bolts Cand slide out the relevant plastic
spacer E. 
6. Open the porthole, take out the inlet hose
from the drum and remove the polystyrene
block fitted with the adhesive tape on the
door seal.Open the porthole, take out the
inlet hose from the drum and remove the
polystyrene block fitted with the adhesive
tape on the door seal.
7. Fill the smaller upper hole and the two large
ones with the corresponding plastic plug
caps supplied in the bag containing the
instruction booklet.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units. Level the washing machine by
raising or lowering the feet. The feet may be
tight to adjust as they incorporate a self locking
nut, but the machine MUST be level and
stable.
Any necessary adjustment can be made with a
spanner. 
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Never place cardboard, wood or similar
materials under the machine to compensate for
any unevenness in the floor.
132970080gb.qxd  13/02/2008  13.44  Page 23
 
						

							If necessary, check the
setting with a spirit
level. 
Water inlet
An inlet hose is supplied and can been found
inside the machine drum.
Do not use the hose from your previous
machine to connect to the water supply.
1. Open the porthole and extract the inlet
hose.
2.Connect the hose
with the angled
connection to the
machine.
Attention !
Do not place the inlet hose downwards.
Angle the hose to the left or right depending
on the position of your water tap.
3. Set the hose correctly by loosening the ring
nut. After positioning the inlet hose, be sure to
tighten the ring nut again to prevent leaks.
4.Connect the hose to
a tap with a 3/4”
thread. Always use
the hose supplied
with the appliance. 
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the tap,
you will have to purchase a new, longer hose
specially designed for this type of use.
45°35°
Water drainage
The end of the drain hose can be positioned in
three ways:
Hooked over the
edge of a sink using
the plastic hose
guide supplied with
the machine.In this
case, make sure the
end cannot come
unhooked when the
machine is emptying. This could be done by
tying it to the tap with a piece of string or
attaching it to the wall.
In a sink drain pipe branch.This branch must
be above the trap so that the bend is at least
60 cm above the ground. 
Directly into a drain pipe at a heightof not
less than 60 cm and not more than 90 cm. The
end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain
pipe must be larger than the outside diameter
of the drain hose.
The drain hose must not be kinked.
Electrical connection
This machine is designed to operate on a 230
V, single-phase, 50 Hz supply.
Check that your domestic electrical installation
can take the maximum load required (2.2 kW),
also taking into account any other appliances
in use.
24
132970080gb.qxd  13/02/2008  13.44  Page 24
 
						

							25
Attention!
Connect the machine to an earthed socket. 
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution. 
Attention!
Should the appliance power supply cable need
to be replaced, this MUST be carried out by
our Service Centre.
NOTE
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of a breakdown.
Environmental concerns
Packaging materials
The materials marked with the symbol  are
recyclable.
>PEPSPP
						

							www.electrolux.com
Subject to change without notice192 997 080 - 01 - 072008
132970080gb.qxd  13/02/2008  13.44  Page 26