Zanussi Zwf 1430 S Manual

							WASHING MACHINE
ZWF 1230 W - ZWF 1430 W
ZWF 1430 S - ZWF 1630 W




 
	
	 	
		











	









 
 
!   #

$%


&

INSTRUCTION BOOKLET132989150GB
132989150.qxd  13/03/2004  09.00  Pagina  1 
						

							2
Installation
●This appliance is heavy. Care should be taken when
moving it.
●It is dangerous to alter the specifications or attempt
to modify this product in any way.
●All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section
in instructions.
●Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
●Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
●Care must be taken to ensure that the appliance does
not stand on the electrical supply cable.
●If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely.
Child Safety
●This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
●Pets and children have been known to climb into
washing machines. Please check your drum before
use.
●The glass door becomes very hot during the washing
cycle. Keep children away from the vicinity of the
appliance whilst it is in operation.
●Keep all packaging well away from children.
●Keep all detergents in a safe place out of children’s
reach.
Use
●Always unplug the appliance and turn off the water
supply after use.
●Do not overload the appliance. See relevant section
in the instruction book.
●Only wash fabrics which are designed to be machine
washed. If in doubt, consult the care label on the clothes.
●Before washing, ensure that all pockets are empty
and buttons and zips are fastened. Avoid washing
frayed or torn articles and treat stains such as paint,
ink, rust, and grass before washing. Underwired bras
must NOT be machine washed.
●Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause
extensive damage and must not be placed into the
machine.
●Garments which have been in contact with volatile
petroleum products should not be machine washed.
If volatile cleaning fluids are used, care should be
taken to ensure that the fluid is removed from the
garment before placing in the machine.
●Wash small items such as socks, laces, washable
belts etc in a washing bag or pillow case as it is
possible for such items to slip down between the tub
and the inner drum.
●Only use the advised quantities of fabric softener.
Damage to the fabric can ensue if you over-fill.
Refer to the manufacturer’s recommendations of
quantities.
●As some duvets and eiderdowns should be washed
in large commercial machines because of their bulk,
please check with the manufacturer of the item
before washing in a domestic machine.
●Leave the porthole door slightly ajar between washes
to preserve the door seal.
●Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Service Force
Centre. Always insist on genuine spare parts.
Important Safety Information
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance and the relevant
warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully
before installing or using the appliance.
132989150.qxd  13/03/2004  09.00  Pagina  2 
						

							3
Contents
For the User
Important Safety Information2
Your New Washing Machine4
Description of the Appliance5
Detergent dispenser drawer 5
Child safety feature 5
The Control Panel6-9
Turning the acoustic signal off 6
Operating sequence10-12
Load the laundry 10
Measure out the detergent 10
Measure out the fabric softener 10
Switch the machine on 10
Select the required programme/fabric 10
Select the temperature 11
Select the spin speed or the Rinse Hold option 11
Select the desired options 11
Select the SUPER RINSE or AA40° option 11
Select the DELAY START 11
Start the programme 12
How to change a programme during its cycle 12
How to cancel a programme during its cycle 12
How to open the door during the cycle of 
a programme 12
End of programme 12
Washing Hints13-14
Which detergent?.... 14
And in which form? 14
Wash Care Symbols15
Washing Programmes16
Maintenance and Cleaning17-18
Descaling 17
After each wash 17
Maintenance Wash 17
External cleaning 17
Cleaning the dispenser drawer 17
Cleaning the drawer recess 17
Cleaning the pump 17-18
Cleaning the water inlet filter 18
The dangers of freezing 18
Emergency emptying out 18
Something Not Working19-20
Service and Spare Parts20
Guarantee Conditions21
For the Installer
Installation Instructions22
Technical Specifications22
Unpacking 23
Positioning 23
Water inlet 24 
Water drainage 24-25
Levelling 25
Special conditions 25
In the interest of the environment 25
Electrical connection 26
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
132989150.qxd  13/03/2004  09.00  Pagina  3 
						

							4
Your New Washing Machine
Your new washing machine meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption. 
Even small loads are washed “economically” because the amount of water used is regulated
automatically according to the load and type of fabric.
●Automatic cooling of the wash water to 60°C
before draining, with the 95°C programme. This
reduces thermal shock to fabrics, helping to prevent
creasing.
●The special wool programmewith its new delicate
wash system treats your woollens with extreme care.
●The anti-unbalance deviceensures that the washing
machine remains stable when spinning.
Ecological hints
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
●Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
●The machine works more economically if it is fully
loaded.
●With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
●Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
In the interest of the
environment
●Materials marked with the symbol  are
recyclable. 
●Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.
●When the appliance is to be scrapped, cut off the
power supply cable and make the door lock device
unusable to prevent young children from being
trapped inside.
●Help to keep your country tidy - use authorised
disposal sites for your old appliance. 
How do we help to protect the environment?
We use recycled paper!
Important
Your machine is fitted with a balance control device, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly
distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the
wash load manually and select a spin programme. For more detailed information see the section headed “Something
Not Working”.
132989150.qxd  13/03/2004  09.00  Pagina  4 
						

							5
Description of the Appliance
1 Detergent dispenser drawer
2 Control panel
3 Door opening handle
4 Drain pump
5 Adjustable feet
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
Child safety feature
This machine incorporates a special child safety feature
to prevent small children from being trapped inside the
machine.
To activate this device, rotate the button (without
pressing it) inside the door clockwise until the groove is
horizontal. If necessary use a coin.
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise until
the groove is vertical.










 
	
	 	
		











	









 
 
!#

$%



&




132989150.qxd  13/03/2004  09.00  Pagina  5 
						

							1 “On/Off” button
Press this button to switch the washing machine on.
The display (8) will show three blinking dashes or a
blinking zero. You will find more detailed explanations
on pages 7-8 (see “DISPLAY”).
Press the On/Off button again to switch the machine
off.
2 MAINS-ON light
This light is connected to the “On/Off” button. It lights
up when you press the button, and goes out when you
press it again.
3 FABRICS button
Press this button repeatedly to select the programme on
the basis of the type of laundry to be washed. The light
relevant to the selected programme will light up. The
washing machine will propose a temperature and
automatically select the maximum spin value provided
for the programme you have chosen. You can change
these values by operating buttons 4 and 5.
Hand wash
When you select this programme, you obtain a
particularly delicate washing, suitable for articles of
clothing whose label indicates that they must be hand-
washed .
4 “Temp.” button
Press this button repeatedly to increase or decrease the
temperature, if you want your laundry to be washed at a
temperature different from the one proposed by the
washing machine. The relevant light will light up.
Maximum temperatures are 95°C for cotton, 60°C for
synthetic fabrics, 40°C for delicate fabrics, wool and
fabrics to be hand-washed (Handwash programme).
6
The Control Panel

	





 
	
	 	
	
	












	











 
 

!#

$%


5 “Spin” button
Press this button repeatedly to change the spin speed, if
you want your laundry to be spun at a speed different
from the one proposed by the washing machine. The
relevant light will light up.
Maximum speeds are:
• for cotton: 1,600, 1,400 or 1,200 rpm depending on
the model;
• for synthetic fabrics, wool and fabrics to be hand-
washed: 900 rpm;
• for delicate fabrics: 700 rpm.
RINSE HOLD position: when you choose this option,
the machine will not drain the water of the last rinse, so
as not to wrinkle the laundry.
At the end of the cycle, the door is locked, the light of
the “Start/Pause” button goes out, the pilot light of
“Rinse Hold” position remains lit, to indicate that the
water must be drained.
To complete the cycle, choose one of the following
options:
• Drain:
Press “Skip Reset” button once, all the leds are off, the
display will show three blinking dashes, then press
FABRIC button in order to select the desired
programme. If you wish to drain or spin press the “Skip
Reset” button until the led of the desired function goes
on.IMPORTANT!
By pressing the “Temp.” and “Spin” buttons
simultaneously, the acoustic signal is deactivated at
the end of the cycle, when selecting the programmes
and in case of an incorrect option selection .
By pressing these 2 buttons again the acoustic signal
is reactivated.
132989150.qxd  13/03/2004  09.00  Pagina  6 
						

							7 You can change the spin speed by means of “Spin”
button and then depress Start/Pause .
Important! If you accidentally press the “Skip Reset”
button more than once, the display will show three
blinking dashes. To drain the water, select any washing
programme by means of the FABRICS button, then
press “Skip Reset” three times in order to select the
drain (only the “drain” light will remain lit). 
6 WASH CHOICE button
Press this button to select the following options:
• Prewash: select this option if you wish your laundry
to be prewashed before the main wash (not available
for wool and hand-wash cycle).
The prewash ends with a short spin at 650 rpm in
programmes for cotton and synthetic fabrics, whereas
in the programme for delicate fabrics the water is only
drained.
• Outdoor Sports: select this option if you wish to
perform a soak of about 30 minutes at 30°C to your
laundry. By pressing the DELAY START button the
soak time can be prolonged up to 10 hours max. After
this time the wash cycle will automatically start. 
This function is not available for wool and hand-wash
cycle.
The soak ends with a short spin at 650 rpm in
programmes for cotton and synthetic fabrics, whereas
in the programme for delicate fabrics the water is only
drained.
• Extra Quick: select this option for laundry that is
only slightly soiled (not for Wool and Handwash
programme).
The washing time will be reduced according to the
type of fabric and the selected temperature.
The Prewash, the Outdoor Sport and the Extra Quick
options cannot be selected together.
7 OPTIONS button
Press this button to select the following options:
• Super Rinse: this option can be selected  with all 
programmes except the wool programme and hand
wash.The machine will add 2 rinses to the selected
programme. This option is recommended for people
who are allergic to detergents, and in areas where the
water is very soft.
•40° AA: this option can be selected for cottons and
synthetics lightly or normally soiled with a
temperature of 40°C or higher.If you select 40°C together with option 40° AA, the
machine will prolong the time at 40°C in the washing
phase. On cotton programme this will allow an A class
in energy efficiency and washing performance to be
achieved.
If you select 95°C, 60°C or 50°C and press the40°
AAbutton, the washing temperature will be reduced
and the washing time will be prolonged.
The Super Rinse and the 40° AA options cannot be
selected together by means of the relevant button.
8 Display
The following pieces of information are shown on the
display:
• Three blinking dashes, when a programme is
cancelled by means of the Skip Reset button.
The three blinking dashes will also appear when you
press the On/Off button to switch the machine on, if the
previously selected cycle has been erased.
•
Duration of washing programmein hours and
minutes, after you have selected a programme.
While the programme is running (after you have
pressed the Start/Pause button), the displayed time
value decreases by one unit every minute.
• The washing machine has stopped with water in the
tub, at the end of a programme with the Rinse Hold
option: this is indicated by a flashing zero.
• The washing machine has completed the
programme: this is indicated by a blinking zero. The
zero will reappear when you switch the washing
machine on, unless the previous programme has been
erased by means of the Skip Reset button.
Important!
The first time you use the washing machine, when
you switch it on, it may display a blinking zero and give
an audible warning signal. This is due to the fact that the
washing machine has performed a washing cycle during
the manufacturer’s inspection tests, and this cycle has
not been erased after its completion.




132989150.qxd  13/03/2004  09.00  Pagina  7 
						

							8 •Delay start, a time value indicated in hours and
selected by means of the relevant button.
The delay time is displayed for 3 seconds, then the
duration of the selected programme reappears.
After you have pressed the Start/Pause button, the
countdown begins, and the delay time value decreases
by one unit every hour.
You can delay the start of the selected programme by
up to 23 hours in one hour intervals.
• An incorrect option selection has been made: this is
indicated by the messageErrwhen a function
incompatible with the current programme is selected.
The incorrect selection is also indicated by an audible
warning signal.
• An alarm codeindicates a fault in the machine
operation (see the relevant chapter on page 19).
9 START/PAUSE button 
This button has two functions:
•Start: after you have selected the desired programme
and options, press this button to start the washing
machine. The light above the button will stop flashing
and remain lit.

If you have selected a delay time by means of button
11, the countdown will begin and will be shown on the
display.
•Pause: when you press this button again, the
programme in progress is interrupted. The light above
the button will start flashing. To restart the programme,
press the button again.
When you PAUSE the cycle, and it becomes possible
to open the door, provided
• the washing machine is not in the heating phase;
• the level of the water is not high;
• the drum is not turning.
Important! You must set the washing machine to Pause
before you make any change in the programme in
progress.
10 SKIP/RESET button
This button performs two functions:
- Clears the memory
- Selects special programmes
At the end of every programme the Reset button must be
pressed once or repeatedly to clear the programme
memory. This will be confirmed by three dashes,
flashing in the display.
If the previous programme is not cleared, the display
will show a “
0” flashing and an audible signal will
sound, when you switch the machine on.
Selecting a special programme:
A wash programme must be selected in the normal way.
(Start button not pressed)
The SKIP button is then used to cancel or advance the
programme to the required  phase. 
The SKIP button can only operate when the programme
is in pause.
A normal wash cycle consists of the following phases,
Wash - Rinses - Spinand is confirmed by the
illumination of the corresponding LED,s. 



132989150.qxd  13/03/2004  09.00  Pagina  8 
						

							9 To select rinses & spin, the programme must be paused,
now press the Skip button once, the washLED goes out.
To select spinonly, the programme must be paused,
now press the Skip button twice. 
The wash &rinsesLED,s go out.
To select Drainthe programme must be paused, now
press the Skip button three times, the wash - rinses -
spinLED,s go out.



	






	






	






	



11 DELAY START button
This button makes it possible to delay the starting of the
programme by up to 23 hours. The delay you have
selected is shown on the display for about 3 seconds;
afterwards, the duration of the programme reappears.
If the button Outdoor Sports has been pressed the
selected delay will correspond to the soak time. If no
delay time is selected the soak programme will last
about 30 minutes. 
You must select this option afteryou have set the
programme and beforeyou press the Start/Pause button.
The time value shown on the display will decrease by
one unit every hour.
You can change the delay time at any moment, before
you press the Start/Pause button.
If you have already pressed the Start/Pause button, and
you wish to changeor cancelthe delay time, proceed as
follows:
• set the washing machine to Pause by pressing the
Start/Pause button;
• press the DELAY button until the display shows the
desired delay time or
• press the DELAY button once, to erase the delay time.
The display will indicate “0 0
’”.
• press the Start/Pause button again.
Important!
The door will be locked throughout the delay time.
If you need to open the door, you must first set the
washing machine to Pause by pressing the Start/Pause
button. After you have closed the door, press the
Start/Pausebutton again.
12 Programme phase indicator
lights
When you select a programme, the lights relevant to the
phases that form the programme light up.
After you have started the programme, only the light
relevant to the phase that is currently being carried out
will remain lit.
132989150.qxd  13/03/2004  09.00  Pagina  9 
						

							10
Operating Sequence
Before the first wash, we recommend that you pour 2
litres of water into the main wash compartment  of
the detergent drawer in order to activate the ECO valve.
Then run a cotton cycle at 60°C, without any laundry in
the machine, to remove any manufacturing residue from
the drum and tub.
Pour 1/2 a measure of detergent into the dispenser
drawer and start the machine.
WASHING 5.5 KG OF WHITE COTTON AT 95°C
Suppose you have 5.5 kg of heavy soiled laundry to
wash. It is white cotton and is suitable for high
temperature washing.
1. Load the laundry
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
Close the door.
2. Measure out the detergent
Pull out the dispenser drawer until it stops. Measure out
the amount of detergent required and pour it into the
main wash compartment  .
If you wish to carry out the prewash or a soak
programme (Outdoor Sports), pour detergent into the
appropriate compartment marked  .
3. Measure out the fabric
softener
If required, pour fabric softener into the compartment
marked , without exceeding the «MAX» mark.




Close the drawer gently.
4. Switch the machine on
Press the On/Off button to switch the machine on. The
display will show three blinking dashes or a blinking
zero. The light above the button will light up.
5. Select the desired programme/
fabric
Press the FABRICS button repeatedly, in order to select
the desired programme/fabric. The relevant light will
light up.
The lights relevant to the phases that form the
programme will light up.
The display will show the duration of the selected
programme, calculated on the basis of the maximum
load for each type of fabric. The Start/Pause button light
will start flashing.
If the load of laundry to be washed is small, at the
beginning of the cycle the display will still indicate the
duration relevant to the maximum load. The duration
value will be gradually adjusted during the cycle.
6. Select the temperature
Press the “Temp.” button if you wish to select a
temperature value different from the one proposed by
the washing machine. 
The relevant light will light up.



	





 

 





132989150.qxd  13/03/2004  09.00  Pagina  10