Zanussi Zrg 614 Sw User Manual

							1. Remove the plug from
the power socket.
2. Tilt back the appliance
carefully so that the com-
pressor cannot touch the
floor.
3. Unscrew both adjustable
feet.
4. Unscrew the screws of
the door bottom hinge. Re-
move the hinge. Put over
the pin in the direction of
the arrow.
5. Unscrew and install the
screw on the opposite side.
6. Install the hinge on the
opposite side.
7. Screw both adjustable
feet.8. Unscrew both screws on
the rear side.
9. Push back the top and lift
it from the fixing elements.10. Unscrew the screws of
the door top hinge.
11. Remove the hinge. Put
over the pin in the direction
of the arrow. Install the
hinge on the opposite side.
12. Tighten the hinge.
13. Put the top in position.
14. Pull it forward.
15. Screw both screws on
the rear side.16. Remove and install the
handle1) on the opposite
side.
17. Reposition, level the
appliance, wait for at least
four hours and then con-
nect it to the power socket.
1) If foreseen
Do a final check to make sure that:
• All screws are tightened.
• The door opens and closes correctly.
If the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that case,
wait for the natural fitting of the gasket.In case you do not want to carry out the above mentioned
operations, contact the nearest After Sales Service Force.
The After Sales Service specialist will carry out the rever-
sibility of the doors at your cost.
 11
 
						

							Reversibility of the freezer door
180˚
Electrical Connection
Caution!  Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Warning!  This appliance must be earthed.
The manufacturer declines any liability should these
safety measures not be observed.
12
3
4
5
Important!  The wires in the mains lead are coloured in
accordance with the following code:
1Green and Yellow: Earth
3Brown: Live
5Blue: Neutral
As the colours of the wires in the mains lead of this ap-
pliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
1. Connect the wire coloured green and yellow to the
terminal marked either with the letter “E“ or by the
earth symbol 
 or coloured green and yellow.
2. Connect the wire coloured blue to the terminal either
marked with the letter “N“ or coloured black.
3. Connect the wire coloured brown to the terminal ei-
ther marked with the “L“ or coloured red.
4. Check that no cut, or stray strands of wire is present
and the cord clamp 
4 is secure over the outer
sheath.
5. Make sure the electricity supply voltage is the same
as that indicated on the appliance rating plate.
6. Switch on the appliance.
12
 
 
						

							The appliance is supplied with a 13 amp plug fitted 2 .
In the event of having to change the fuse in the plug sup-
plied, a 13 amp ASTA approved (BS 1362) fuse must be
used.Warning!  A cut off plug inserted into a 13 amp
socket is a serious safety (shock) hazard. Ensure
that it is disposed of safely.
Environmental concerns
The symbol    on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potentialnegative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed
information about recycling of this product, please
contact your local council, your household waste disposal
service or the shop where you purchased the product.
 13
 
						

							14
 
 
						

							 15
 
						

							To buy accessories, consumables and spare parts at our online shop please visit:
www.zanussi.co.uk
www.zanussi.com
200383439-00-18032010