Zanussi Zrb 936 Pwh User Manual

compressor may run continuously, causing
frost or ice on the evaporator. If this happens,
set the Temperature Regulator toward warm-
er settings to allow automatic defrosting and
so a saving in electricity consumption.
Hints for fresh food refrigeration
To obtain the best performance:
• do not store warm food or evaporating liq-
uids in the refrigerator
• do cover or wrap the food, particularly if it
has a strong flavour
• position food so that air can circulate freely
around it
Hints for refrigeration...

• clean the inside and accessories with luke-
warm water and some neutral soap.
• regularly check the door seals and wipe
clean to ensure they are clean and free from
debris.
• rinse and dry thoroughly.
Important! Do not pull, move or damage any
pipes and/or cables inside the cabinet.
Never use detergents, abrasive powders, highly
perfumed cleaning products or wax polishes to
clean the interior as this will damage the
surface and leave a strong odour.
Clean the condenser (black grill) and the com-...

mostatic control for some hours so that it
can reach the sufficient storing tempera-
ture as soon as possible.
Important! Never use sharp metal tools to
scrape off frost from the evaporator as you
could damage it. Do not use a mechanicaldevice or any artificial means to speed up the
thawing process other than those
recommended by the manufacturer. A
temperature rise of the frozen food packs,
during defrosting, may shorten their safe
storage life.
Troubleshooting
Caution! Before troubleshooting,...

ProblemPossible causeSolution
The temperature in the ap-
pliance is too high.The Temperature regulator may be
set incorrectly.Set a lower temperature.
 The door is not closed correctly.Refer to "Closing the door".
 The product temperature is too
high.Let the product temperature de-
crease to room temperature before
storage.
 Many products are stored at the
same time.Store less products at the same
time.
The temperature in the re-
frigeration is too high.There is no cold air circulation in
the...

Technical data
   
Dimension  
 Height1850 mm
 Width595 mm
 Depth658 mm
Rising Time 20 h
Voltage 230-240 V
Frequency 50 Hz
The technical information are situated in the rat-
ing plate on the internal left side of the appli-
ance and in the energy label.
Installation
Caution! Read the "Safety Information"
carefully for your safety and correct
operation of the appliance before installing the
appliance.
Positioning
Install this appliance at a location where the
ambient temperature corresponds to the...

2. Engage the spacer below the screw.
3. Turn the spacer to the right position.
4. Tighten again the screws.
2
431
Levelling
When placing the ap-
pliance ensure that it
stands level. This can
be achieved by two
adjustable feet at the
bottom in front.
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the rating plate corre-
spond to your domestic power supply.
The appliance must be earthed. The power
supply cable plug is provided with a contact for
this purpose. If...

• Open the doors.
Unscrew the middle
hinge (B). Remove
the plastic spacer
(A).
• Remove the spacer
(F) and move to the
other side of the
hinge pivot (E).
• Remove the doors.
• Remove the left-
hand cover pin of
the middle hinge
(C,D) and move to
the other side.
• Fit the pin of the
middle hinge (C) in-
to the left-hand hole
of the lower door.• Unscrew the lower
hinge (A)
• Remove the left-
hand cover pins (D)
and move to the
other side.
• Re-screw the lower
hinge (A) on the op-
posite side.
• Unscrew the...

Sommaire
Consignes de sécurité _ _ _ _ _ _ _ _ _ _ _  28
Description de l'appareil _ _ _ _ _ _ _ _ _ _  31
Fonctionnement _ _ _ _ _ _ _ _ _ _ _ _ _ _ _  31
Première utilisation _ _ _ _ _ _ _ _ _ _ _ _ _  32
Utilisation quotidienne _ _ _ _ _ _ _ _ _ _ _  32
Conseils utiles _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _  33Entretien et nettoyage _ _ _ _ _ _ _ _ _ _ _  34
En cas d'anomalie de fonctionnement _  _  _   36
Caractéristiques techniques _ _ _ _ _ _ _ _  38
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _...

Pendant le transport et l'installation de votre
appareil, assurez-vous qu'aucune partie du
circuit frigorifique n'est endommagée.
Si le circuit frigorifique est endommagé :
– évitez les flammes vives et toute autre
source d'allumage
– aérez soigneusement la pièce où se trouve
l'appareil
• Ne modifiez pas les spécifications de l'appa-
reil. Si le câble d'alimentation est endomma-
gé, il peut causer un court circuit, un incen-
die et/ou une électrocution.
Avertissement Les...

• Déballez l'appareil et vérifiez qu'il n'est pas
endommagé. Ne branchez pas l'appareil s'il
est endommagé. Signalez immédiatement au
revendeur de l'appareil les dommages cons-
tatés. Dans ce cas, gardez l'emballage.
• Il est conseillé d'attendre au moins quatre
heures avant de brancher l'appareil pour que
le circuit frigorifique soit stabilisé.
• Veillez à ce que l'air circule librement autour
de l'appareil pour éviter qu'il ne surchauffe.
Pour assurer une...