Zanussi Zi 9225 Instruction Booklet

							11
ZI 9155 ZI 9225
POWER SUPPLY VOLTAGE AND FREQUENCY 220-240 V / 50 Hz 220-240 V / 50 Hz
TOTAL POWER ABSORBED 100 W 140 W
AVERAGE DAILY UNITS ELECTRICITY
(*)0,49 kWh 0,53 kWh
GROSS CAPACITY 158 l 230 l
NET CAPACITY 154 l 228 l
(*) This figure is based on standard test results in accordance with European Standard EN153. Actual
consumption will depend on how the appliance is used and where it is located.
Technical specifications
Warning
IF YOU ARE  DISCARDING AN  OLD
APPLIANCE THAT HAS A LOCK OR CATCH
ON THE DOOR, YOU MUST ENSURE THAT
IT IS MADE UNUSABLE TO PREVENT
YOUNG CHILDREN BEING TRAPPED
INSIDE.
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
under ÒDoor reversalÓ.
Positioning
The appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located on the inside left of the appliance.
The following table shows which ambient
temperature is correct for each climate classification.
SN +10¡C   to   +32¡C
ST +18¡C   to   +38¡C
Installation
The appliance should be located in a dry
atmosphere, out of direct sunlight and away from
continuous heat and extreme temperature, e.g. not
next to a boiler or radiator or in a very cold room e.g.
an outhouse. If these temperatures are exceeded i.e.
warmer or colder, then the appliance may not
operate correctly.
For building-in and door reversal instructions please
refer to the relevant instructions on the following
pages.
Important
It mustbe possible to disconnect the appliance
from the mains power supply; the plug must
therefore be easily accessible after installation.
 
						

							12
Door reversal
The applianceÕs door has been locked in position for
transport by means of pins on both sides. According
to the door opening direction, remove relevant pins
at the top and at the bottom.
Attention
After completion of the door reversing
operation, check that the door gasket adheres
to the cabinet. If the ambient temperature is
cold (i.e. in Winter), the gasket may not fit
perfectly to the cabinet. In that case, wait for
the natural fitting of the gasket or accelerate
this process by heating up the part involved
with a normal hairdryer on a low setting.
B A
 
						

							13
If you fit your own plug, the colours of the wires in the
mains lead of your appliance, may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
Connect the Green and the Yellow (earth) wire to the
terminal in the plug which is marked with the letter
ÇEÈ or the earth symbol  , or coloured green and
yellow.
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter ÇNÈ or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter ÇLÈ or coloured
red.
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BS1362 fuse. Only
ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
This appliance complies with the following E.E.C.
Directive:
-73/23 EEC 
of 19.2.73 (Low Voltage
Directive) and subsequent amendments.
- 87/308 of 2.6.87 (Radio Interference
Suppression) and subsequent amendments.
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
amendments.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of breakdown.
Electrical Connection
WARNING
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability
should this safety measure not be
observed.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
D207
GREEN & YELLOW
13 AMP. FUSE
BROWN
CORD CLAMP BLUE
13 AMP
 
						

							Dimensions of the recess
ZI 9155ZI 9225
Height of housing (1) mm  8801225
Depth of housing (2) mm  550 550
Width of housing (3) mm  560 560
It is necessary that the cabinet has a ventilation
recess with the following dimensions:
Depth 50 mm Width 540 mm
Building in
PR0
540
50
3
21
For appropriate venting, follow indications in the
figure.
50 mm
min.
200 cm2
200 cm
2
min.
D526
D022
1
2
1.Push the appliance into the housing until stop strip
touches the kitchen unit.
14
2.Press in the joint covers between the appliance
and the kitchen furniture.
D132
3.Open the door and push the appliance against the
side of kitchen furniture opposite to that of the
appliance hinges. Fasten the appliance with 4
screws (I) provided in the kit included with the
appliance.
4.Snap vent grill (B) and hinge cover (E) into
position.
Apply blanking covers (C-D) as indicated.
I
B E
C
D
 
						

							15
PR266
AB
C
D
6.Place guide (A) on the inside part of the furniture
door, up and down as shown in the figure and
mark the position of external holes. After having
drilled holes, fix the guide with the screws
supplied.
20mm
A
50mm
PR166
PR33/2
C
A
8.Open the appliance door and the furniture door at
90¡. Insert the small square (B) into guide (A). Put
together the appliance door and the furniture door
and mark the holes as indicated in the figure. 
Remove the squares and drill holes with ¯ 2 mm
at 8 mm from the outer edge of the door. Place the
small square on the guide again and fix it with the
screws supplied.
8mm
PR167
A
B
9.Should the alignment of the furniture door be
necessary, use the clearance of slots.
At the end of this procedure, it is necessary to
check if the door of the furniture closes properly.
PR168
10.Fix cover (D) on guide (B) until it clips into place.
PR167/1
D
B
5.Separate parts A, B, C, D as shown in the figure.
7.Fix cover (C) on guide (A) until it clips into place.
 
						

							© Electrolux plc 2004923631675 / 923527614