Zanussi Zdf 3020 User Manual

Activate or deactivate the multitab function before
the start of a washing programme.
You cannot activate or deactivate the multitab function
when the programme operates. Cancel the washing pro-
gramme, then set the programme again.
To activate the multitab function:
• Press the multitab button. The multitab indicator light
comes on.
To deactivate the multitab function:
• Press the multitab button. The multitab indicator light
goes off.
Do these steps if the drying results are not satis-
factory:
1. Fill...

The washing programme is cancelled.
At this time you can do these steps:
1. Switch off the appliance.
2. Set a new washing programme.
Fill the detergent dispenser with detergent before you
set a new washing programme.
Setting and starting a washing programme with
delay start
1. Set a washing programme.
2. Press the delay start button until the display shows
the necessary delay start time for the washing pro-
gramme. Delay start time flashes in the digital dis-
play.
3. Press the start/cancel button.
–...

3
To remove filters B and C,
turn the handle approxi-
mately 1/4 anticlockwise.
4
Remove the flat filter A
from the bottom of the ap-
pliance.
5
Put the flat filter A in the
bottom of the appliance.
Install the flat filter cor-
rectly under the two
guides D.
6
Put the filter system in po-
sition. To lock the filter
system, turn the handle
clockwise until it locks in
position.
Important!  Do not remove the spray arms.
If the holes in the spray arms become clogged, remove
remaining parts of soil with a...

Fault code and malfunctionPossible cause and solution
•
the digital display shows 
The dishwasher will not drain
• There is a blockage in the sink spigot.
Clean the sink spigot.
• The connection of the water drain hose is not correct. The hose can
be kinked or squashed.
Make sure that the connection is correct.
•
the digital display shows 
The anti-flood device operates
• Close the water tap and contact your local Service Force Centre.
The programme does not start• The appliance door is not closed.
Close...

The cleaning results are not satisfactory
Dry water drop signs on glasses
and dishes• Increase rinse aid dosage.
• The detergent can be the cause.
Technical data
DimensionsWidth cm60
 Height cm85
 Depth cm61
Electrical connection - Voltage -
Overall power - FuseInformation on the electrical connection is given on the rating plate on the
inner edge of the dishwasher door.
Water supply pressureMinimum0,5 bar (0,05 MPa)
 Maximum8 bar (0,8 MPa)
CapacityPlace settings12
Environment concerns
The symbol    on...

12
34
Install the appliance worktop to the appliance if you want
to use the dishwasher as a freestanding appliance.
The plinth on freestanding appliance is not adjustable.
Adjusting the level of the appliance
Make sure that the appliance is level to close and seal the
door correctly. If the level of the appliance is correct, the
door does not catch on the sides of the cabinet. If the door
does not close correctly, loosen or tighten the adjustable
feet until the appliance is level.
Water connection
Water...

If you connect the water drain hose to a trap spigot under
the sink, remove the plastic membrane (A). If you do not
remove the membrane, remaining food can cause a block-
age in the drain hose spigot.Caution!  Make sure that the water couplings are
tight to prevent water leakage.
Electrical connection
Warning!  The manufacturer is not responsible if
you do not follow these safety precautions.
This appliance needs to be earthed according to safety
precautions.
Make sure that the rated voltage and type of...

18
 
 

 19
 

To buy accessories, consumables and spare parts at our online shop please visit:
www.zanussi.co.uk
www.zanussi.com
156985782-00-102009