Zanussi Zba 6230 Instruction Booklet

							11
Door reversal
The appliance’s door has been locked in position for
transport by means of pins on both sides. According
to the door opening direction, remove the relevant
pins at the top and at the bottom.Attention
After completion of the door reversing
operation, check that the door gasket adheres
to the cabinet. If the ambient temperature is
cold (i.e. in Winter), the gasket may not fit
perfectly to the cabinet. In that case, wait for
the natural fitting of the gasket or accelerate
this process by heating up the part involved
with a normal hairdryer on a low setting.
B A
 
						

							12
If you fit your own plug, the colours of the wires in the
mains lead of your appliance, may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
Connect the Green and the Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol  , or coloured green and
yellow.
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BS1362 fuse. Only
ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
This appliance complies with the following E.E.C.
Directive:-73/23 EEC of 19.2.73 (Low VoltageDirective) and subsequent amendments.
- 87/308  of 2.6.87 (Radio Interference
Suppression) and subsequent amendments.
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent
amendments.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of breakdown.
Electrical Connection
WARNING
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability
should this safety measure not be
observed.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
D207
GREEN & YELLOW
13 AMP. FUSE
BROWN
CORD CLAMP
BLUE
13 AMP
 
						

							13
Dimensions of the recessZI 9155 AZI 9225 A
Height of housing (1) mm  880 1225
Depth of housing (2) mm  550 550
Width of housing (3) mm  560 560
It is necessary that the  cabinet has a ventilation
recess with the following dimensions:
Depth 50 mm Width 540 mm
Building in
PR0
54050
3
2 1
For appropriate venting, follow indications in the
figure.
50 mm
min.
200 cm2
200 cm
2
min.
D526
2. Press in the joint covers between the appliance
and the kitchen furniture.
D132
3. Open the door and push the appliance against theside of kitchen furniture opposite to that of  the
appliance hinges. Fasten the appliance with 4
screws  (I)provided in the kit included with the
appliance.
I
D022
1
2
1. Fit the appliance in the niche by making sure that it stands against the interior surface of the unit on
the side where the door hinges of the appliances
are fitted. Insert the appliance until the upper strip
butts up against the unit (1) and make sure that
the lower hinge is in line with the surface of the
unit (2).
 
						

							PR167
Ha
Hb
8mm
14
6. Place guide (Ha) on the inside part of the furniture door, up and down as shown in the figure and
mark the position of external holes. After having
drilled holes, fix the guide with the screws
supplied.
8. Open the appliance door and the furniture door at90°. Insert the small square (Hb) into guide (Ha).
Put together the appliance door and the furniture
door and mark the holes as indicated in the figure. 
5. Separate parts  Ha, Hb, Hc, Hdas shown in the
figure.
7. Fix cover (Hc) on guide (Ha) until it clips into place.
4. Snap vent grill ( B) and hinge cover ( E) into
position.
Apply blanking covers ( C-D) as indicated.
B
E
C
D
PR266
Ha Hb
Hc
Hd
21 mm
21 m m
ca. 50 mm
90°
90°
ca. 50 mm
PR33
Hc
Ha
PR167
Ha
8mm
K
9. Remove the  squaresand mark a distance of 
8 mm from the outer edge of the door where the
nail must be fitted (K).
 
						

							15
10. Place the small square on the guide again and fixit with the screws supplied.
Should the alignment of the furniture door be
necessary, use the clearance of slots.
At the end of  this procedure , it is necessary to
check if the door of the furniture closes properly.
PR168Hb
11. Fix cover ( Hd) on the small square (Hb) until it
clips into place.
PR167/1
Hd
Hb
 
						

							© Electrolux plc 2007