Zanussi Fcs 725 Instruction And Installation Booklet

11 
Wool 1.0 kg dry load weight
Special programmes 3.0 kg dry load weight
Load 
type
Woollens
garments with wool
symbol or marked
with ”Machine
washable”.
Rinses
this programme can
be used for rinsing
hand washed
garments.
Cold
40°
Cold
Wash programme Cold,
40°C without pre wash.3 rinses and spin max.
900 rpm/min.
Spin
separate spin for
hand washed
items.
Reset
Draining and spin 
max. 900 rpm/min.
Reset the programme. 
Switches the machine
off.
3 rinses and spin 
max. 900 rpm/min.
Temperature
°COption...

12 
Using the appliance
Have you removed all the transit locking devices?
The very first time the machine is used, you should
run awash programme without any load, to clear any
residues which may have been left by the manufac
turing process. Pour approx. 100 ml of detergent
straight into the drum and run a programme at 60°C.When the programme is finished, the machine will be
ready for use.
Starting a wash programme
Before starting up the machine, check that:
the door is properly closed
the appliance is...

13 
Changing a wash programme
The programme can be changed as long as the Start/Pause
button hasn’t been depressed. If the programme has
started, you can only change it by turning the programme
selector to the ”Reset” position and cancel the programme.Select a new programme and press the Start/Pause button.
If you turn the programme selector to another 
programme when the machine is running, the 
lights in the programme progress display start to
flash. The machine will not perform the new
selected...

14 
Maintenance and cleaning
The cabinet
Clean the outside surfaces of the appliance using a mild
(nonabrasive) household cleaning product. Finish by re
moving remaining traces of the product with a damp cloth.
Do not use cleaning products which contain
alcohol (spirits), thinners and similar substances.
The detergent dispenser
In time, residues of detergent and fabric conditioner are
likely to build up inside the detergent dispenser. It should
be cleaned at regular intervals by flushing it out with...

15 
If the machine is not working
The machine will not start.
The machine is not filling with water.
The machine is discharging water at the
same time as filling.
The machine will not empty or spin.
The machine is leaking or overflowing.
The machine is vibrating or noisy.
The machine door will not open.
• Is the door closed properly?
• Have you pressed the Start button?
• Is the water tap turned on?
• Is the machine plugged in?
• Has the fuse blown?
• Have you set the programme selector properly?
• Is...

16 
Service
Service and spare parts
Servicing and possible repairs must be carried out by 
a service company authorised by the supplier. Use only
spare parts supplied by these. 
Before calling service, use the trouble shooting table 
”If the machine is not working” to try to attend to the fault
yourself. Note that electrical faults shall always be
rectified by a certified electrician.
Give the appliance’s model designation, product and
serial numbers according to the data plate.
You can record these...

17 
Unpacking
Damages
If the machine has been damaged during transport, you
should immediately notify the company responsible for
delivering it.
Check that the machine is undamaged. If you discover
any damage, faults or that anything is missing, you should
notify the dealer immediately.
Never leave packaging material in a place
where children may play with it.
When lifting the machine
Be careful when lifting the machine. Incorrect methods of
lifting can cause physical injuries and also increase the
risk...

18 
Installation
Levelling the machine
The machine must be installed on a sound and
firm surface and must not be touching walls or
furniture. Adjust the two front feet to level themachine. Make sure the machine is resting on 
all four feet (Fig. 1).
Some vibration is normal and unavoidable when
the machine is spinning the load, particularly if 
the floor is not a concrete one.
When the appliance location is on
carpet floors, attention must be paid 
so as to ensure that there is no
obstruction to the...

19 
Installation
Water discharge
The discharge hose can be placed in these three ways:
Over the top edge of a washtub:
Use this option only if you can be sure that the hose will
not move when the machine is draining. The hose can
be fixed to the wall on a hook or tied to the tap with a
string (Fig. 1).
Directly into a waste pipe with a trap:
The discharge pipe can be connected directly into the
pipe (e.g. one beneath a washtub or kitchen sink), above
the water trap. The discharge hose must be arranged
so...