Yamaha Yzf R1 2007 Manual
Here you can view all the pages of manual Yamaha Yzf R1 2007 Manual. The Yamaha manuals for Motorcycle are available online for free. You can easily download all the documents as PDF.
Page 391
IMMOBILIZER SYSTEM 8-72 * Accessory locks mean the seat lock and fuel tank cap. Code re-registering key registration: When the immobilizer unit or ECU is replaced, the code re-registering key must be registered to the unit. To register a code re-registering key: 1. Turn the main switch to “ON” with the code re-registering key. NOTE: Check that the immobilizer system indicator light comes on for one second, then goes off. When the immobilizer system indicator light goes off, the code re-registering key...
Page 392
IMMOBILIZER SYSTEM 8-73 Standard key registration: Standard key registration is required when a standard key is lost and needs to be replaced, or when the code re-registering key is re-registered after the immobilizer unit or ECU are replaced. NOTE: Do not start the engine with a standard key that has not been registered. If the main switch is turned “ON” with a standard key that has not been registered, the immobilizer system indicator light flashes to indicate fault code “52”. (Refer to...
Page 393
IMMOBILIZER SYSTEM 8-74 Voiding the standard key code: If a standard key has been lost, it is possible to disable its use by re-registering the remaining stan- dard key. Standard key registration erases the stored standard key code from the memory, thus dis- abling the lost standard key.To re-register, refer to “Standard key registration”. Standard key code voiding method EAS27701 TROUBLESHOOTING When the main switch is turned to “ON”, the immobilizer system indicator light does not come on nor...
Page 394
IMMOBILIZER SYSTEM 8-75 NG→ OK↓ EAS27721 SELF-DIAGNOSIS FAULT CODE INDICATION When a system failure occurs, the error code number is indicated in the LCD display of meter and the immobilizer system indicator light blinks at the same time. The pattern of blinking also shows the error code.4 Check the entire immobilizer sys- tem wiring. Refer to IMMOBILIZER SYSTEM on page 8-69.Properly connect or repair the immobi- lizer system wiring. Check the condition of the each immobilizer system circuits. ...
Page 395
IMMOBILIZER SYSTEM 8-76 Immobilizer system indicator light fault code indication Digit of 10 : Cycles of 1 sec. ON and 1.5 sec. OFF. Digit of 1 : Cycles of 0.5 sec. ON and 0.5 sec. OFF. Example: fault code 5254 IMMOBILIZER UNITCodes transmitted between the ECU and the immobilizer unit do not match.Noise interference or dis- connected lead/cable. 1 Interference due to radio wave noise. 2 Disconnected commu- nication harness. 3 Immobilizer unit mal- function. 4 ECU failure. (The ECU or immobi- lizer...
Page 397
ELECTRICAL COMPONENTS 8-78 1. Main switch 2. Immobilizer unit 3. Front brake light switch 4. Clutch switch 5. Fuel injection system fuse 6. Starter relay 7. Battery 8. Main fuse 9. Neutral switch 10.Rear brake light switch 11.EXUP servo motor 12.Sidestand switch 13.O 2 sensor 14.Speed sensor 15.Oil level switch 16.Ignition coil 17.Radiator fan motor 18.Rectifier/regulator 19.Horn 20.Fuse box (radiator fan motor, signaling sys- tem, ignition, ETV, backup) 21.Fuse box (headlight)
Page 399
ELECTRICAL COMPONENTS 8-80 1. Air temperature sensor 2. Atmospheric pressure sensor 3. Fuel pump 4. Coolant temperature sensor 5. Starting circuit cut-off relay 6. Turn signal relay 7. ECU (engine control unit) 8. Lean angle sensor 9. Crankshaft position sensor 10.Intake air pressure sensor 11.Throttle servo motor 12.Throttle position sensor (for throttle cable pulley) 13.Throttle position sensor (for throttle valves) 14.Cylinder identification sensor 15.Radiator fan motor relay 16.Headlight relay...