Home > Yamaha > Motorcycle > Yamaha Wr 450 F Owners Manual

Yamaha Wr 450 F Owners Manual

Here you can view all the pages of manual Yamaha Wr 450 F Owners Manual. The Yamaha manuals for Motorcycle are available online for free. You can easily download all the documents as PDF.

Page 131

4 - 8
ENGCARBURETOR
CARBURETOR
7 4
108
9
T R..2 Nm (0.2 m • 
kg, 1.4 ft • Ib)
2
3
75
5
T R..4 Nm (0.4 m • 
kg, 2.9 ft • Ib)
T R..3 Nm (0.3 m • kg, 2.2 ft • Ib)
6
T R..3 Nm (0.3 m • kg, 2.2 ft • Ib)
1
T R..4 Nm (0.4 m • 
kg, 2.9 ft • Ib)
T R..11 Nm (1.1 m • 
kg, 8.0 ft • Ib)
Extent of removal:1 Carburetor removal
Extent of removal Order Part name Q’ty Remarks
CARBURETOR REMOVAL
Preparation for removal Fuel tank Refer to “SEAT, FUEL TANK AND SIDE 
COVERS” section.
1 Clamp 1
2 Band 1
3 TPS coupler 1
4...

Page 132

4 - 9
ENGCARBURETOR
CARBURETOR DISASSEMBLY
Extent of removal:1 Carburetor disassembly
Extent of removal Order Part name Q’ty Remarks
CARBURETOR DISASSEMBLY
1Breather hose 4
2Valve lever housing cover 1
3Screw (throttle shaft) 1
4Throttle valve 1
5Needle holder 1
6Jet needle 1
7Cover 1
8Spring 1
9Diaphragm (accelerator pump) 1
0Air cut valve cover 1
ASpring (air cut valve) 1
BDiaphragm (air cut valve) 1
CFloat chamber 1
DLeak jet 1
EPilot screw 1 Refer to “REMOVAL POINTS”.
FFloat pin 1
GFloat 1
1 

Page 133

4 - 10
ENGCARBURETOR
Extent of removal Order Part name Q’ty Remarks
HNeedle valve 1
IMain jet 1
JNeedle jet 1
KSpacer 1
LPilot jet 1
MStarter jet 1
NPush rod 1 Pull the push rod.
OThrottle shaft assembly 1
PPush rod link lever assembly 1
QPilot air jet 1
RCold starter plunger 1
1 

Page 134

4 - 11
ENGCARBURETOR
EC466020
HANDLING NOTE
CAUTION:
Do not loosen the screws {TPS (throttle
position sensor)} 1 except when changing
the TPS (throttle position sensor) due to
failure because it will cause a drop in
engine performance.
1
REMOVAL POINTS
Pilot screw
1. Remove:
Pilot screw 1 
NOTE:
To optimize the fuel flow at a small throttle
opening, each machine’s pilot screw has been
individually set at the factory. Before removing
the pilot screw, turn it in fully and count the
number of turns. Record...

Page 135

4 - 12
ENGCARBURETOR
Needle valve
1. Inspect:
Needle valve 1 
Valve seat 2 
Grooved wear a → Replace.
Dust b → Clean.
EC464300
Throttle valve
1. Check:
Free movement
Stick → Repair or replace.
Insert the throttle valve 1 into the car-
buretor body, and check for free move-
ment.
EC464400
Jet needle
1. Inspect:
Jet needle 1 
Bends/wear → Replace.
Clip groove
Free play exists/wear → Replace.
Clip position
Standard clip position:
No.4 Groove
EC464511
Float height
1. Measure:
Float height a 
Out of...

Page 136

4 - 13
ENGCARBURETOR
Measurement and adjustment steps:
Hold the carburetor in an upside down
position.
NOTE:
Slowly tilt the carburetor in the opposite
direction, then take the measurement
when the needle valve aligns with the float
arm.
If the carburetor is level, the weight of the
float will push in the needle valve, result-
ing in an incorrect measurement.
Measure the distance between the mating
surface of the float chamber and top of the
float using a vernier calipers.
NOTE:
The float arm should...

Page 137

4 - 14
ENG
Accelerator pump
1. Inspect:
Diaphragm (accelerator pump) 1 
Spring 2 
Cover 3 
O-ring 4 
Push rod 5 
Tears (diaphragm)/damage → Replace.
Dirt → Clean.
2. Inspect:
Throttle shaft 1 
Spring 2 
Lever 1 3 
Spring 1 4 
Lever 2 5 
Spring 2 6 
Dirt → Clean.
12
3456
Air cut valve
1. Inspect:
Diaphragm (air cut valve) 1
Spring (air cut valve) 2
Air cut valve cover 3
O-ring 4
Tears (diaphragm)/damage → Replace.
1
23
4
ASSEMBLY AND INSTALLATION
Carburetor
1. Install:
Cold starter plunger...

Page 138

4 - 15
ENGCARBURETOR
3. Install:
Spring 1 1 
Lever 1 2 
To lever 2 3.
NOTE:
Make sure the spring 1 fits on the stopper a of
the lever 2.
a
31
2
4. Install:
Spring 2 1 
To lever 2 2.
1
2
5. Install:
Push rod link lever assembly 1 
NOTE:
Make sure the stopper a of the spring 2 fits
into the recess b in the carburetor.
1
a b
6. Install:
Plain washer 1 
Circlip 2 
21
7. Install:
Spring 1 
To throttle shaft 2.
NOTE:
Install the bigger hook a of the spring fits on
the stopper b of the throttle shaft...

Page 139

4 - 16
ENGCARBURETOR
8. Install:
Throttle shaft assembly 1 
Plain washer (metal) 2 
Plain washer (resin) 3 
Valve lever 4 
NOTE:
Apply the fluorochemical grease on the bear-
ings.
Fit the projection a on the throttle shaft
assembly into the slot b in the TPS (throttle
position sensor).
Make sure the stopper c of the spring fits
into the recess in the carburetor.
Turn the throttle shaft assembly left while
holding down the lever 1 5 and fit the throt-
tle stop screw tip d to the stopper e of the...

Page 140

4 - 17
ENGCARBURETOR
11. Install:
Needle valve 1 
Float 2 
Float pin 3 
NOTE:
After installing the needle valve to the float,
install them to the carburetor.
Check the float for smooth movement.
12. Install:
Pilot screw 1
Spring 2 
Washer 3 
O-ring 4 
* Except for USANote the following installation points:
Turn in the pilot screw until it is lightly
seated.
Turn out the pilot screw by the number of
turns recorded before removing.
Pilot screw:
1-3/4 turns out (example)
*1-1/2 turns out...
Start reading Yamaha Wr 450 F Owners Manual

Related Manuals for Yamaha Wr 450 F Owners Manual

All Yamaha manuals