Yamaha Rx 7 User Manual

2. Adjust  the volume  (= level)  with the  DATA slider or
-  1/NO and  + 1/YES keys.
JOB #06 : PAN
FUNCTIO NSets basic  pan position  of selected  voice.
•  Range : 0  (full left) to 15 (full  right)
OPERATIO N
1. Selec t Job  #06.  The lower  display line  show s
The  basi c pan  position  of the  selecte d voic e can  be confirmed
visually  with the above  graphic  display.
2 . Adjust  the pan  position  with the  - 1/NO  and + 1/YES
keys  or DATA slider.
*  The  pan position  affects the  maximum...

OPERATION
1. Select  Job #09.  The lower  display line asks
2.   If  you  do  no t  want to  recall,  press  - 1/NO. Otherwise press  + 1/YES.  The display will ask you to  confirm:
3 . Pres s +  1/YES  (or - 1/NO  to cancel).
The  previously edited  data is recalled, and  the LCD
switches  to the Voice Select  display.  You can now con-
tinu e editing that  voice or  store  the recalled  data.
JOB  #10: LFO
FUNCTIO NSet LFO  parameters  for selecte d voice.
On  the RX7,  LFOs  (Low Frequency...

Parameter 

KEY ASSIGN
OVERVIEW
The Key  Assig n mode  lets you:
*  Assign  any voic e to  any Instrument key.
*  Assign  one voic e to  the  whole upper  row of Instrument  keys.
*  Alter  the pitch , level , pan and  decay o f voice s for  eac h Instrument  key.
*  Adjust  the accen t level s for  eac h Voice .
*  Assig n a  function  to a connected foot  switch.
*  Sav e al l Key  Assig n dat a to  on e o f four  internal memory  locations.
*  Loa d Key  Assig n dat a from  memories.
NOTE : Th e “Drum  Set” Chart...

Example: The  MULTI LED lights  up, and  you  can now  continue
immediatel y with  Mult i Step setting  as described  below.
JOB #04: MULTI  STEP
The above display means  that th e decay value  of 1 6 for  the
selected  key is 5 units  larger  (+) than  the basi c Edit  Voice
value  of 11 . (An  offset  of 0 0 thus  indicates  that the key  value
i s  currently  identical with the basi c value.)
*  Note  that the Edit  Voice value  can only be offset  up to
its  own  minimum  or maximum.  Once this is...

that key  will  then  sound  the same , sinc e they  are
“overstepping”  the minimum/maximum  Edit Voice  value.
I f  thi s happens, you  may want to alter the respective  Edit
Voice  parameter  value.
1: PITCH Ste p -20 0 ~  +20 0 cents  (in 10-cen t steps),
i.e. up to +/- 1 whole tone.
Setting  positive  values, e.g . +10 0 (= 1  semitone),  creates
a  scal e o f notes  that get higher  towards  the right, like
on  a piano.  Negative  values like - 20 0 ( = 1  whole  tone)
caus e the notes to become...

The name  of th e function/ke y will show  on the LCD  (if
a key  has several  functions,  only one is displayed). The
cursor  disappears,  indicating that assignment  is com-
pleted.
Example:
3. The  message
shows  that the  Key Data  has been  loaded.
*  I f +  1/YES  is pressed again,  the Instrument  keys are reset
to  the  voice s prior  to Key  Data load.
JOB #07: KEY  DATA SAVE
FUNCTIONSaves the current Instrument key layout and
other  Key  Assign settings to the internal
memory  of the  RX7....

MIDI
OVERVIEW
The variety  of applications  for these  functions  is enormous, letting  you use the RX7  as a state-of-the-art MIDI  sound source and
controller.  For examples,  they allow  you to:
*  Pla y any  or all RX7  voice s from  up to 16 external  keyboards and/or  sequencers by assigning  MIDI note numbers to each  RX7
instrument  and MIDI  channels  to as many  as 1 6 o f them.
*  Use  single RX7  voice s a s sound  source s for  external  keyboards or sequencers,  allowing you e.g. to  play...

words, that single voice can then 

2. To switch between the two types of displays. “Note