Yamaha Projector DPX 530 User Manual

27
◆Viewing ceiling mounted projector images
To view images projected by the ceiling mounted projector from the front:
When the projector is installed on the ceiling, the special ceiling mount bracket, which is commercially available, is required . Be sure to ask a 
certified installation specialist  for installation of the projector.  Contact your dealer for details.
 Yamaha assumes no responsibilities for any da mage caused by use of other manufacturer s ceiling bracket and by inadequate inst allation...

28
This projector is equipped with a lamp to project images. This lamp is a cons umable, so it may burn out or its brightness may decrease during 
use. If this happens, replace the  lamp with a new one as soon as possible. Be sure  to replace the lamp with a new, commercially available lamp 
that is exclusive to this projector. C ontact your dealer for purchase of the lamp.
Warning
 Be careful not to drop the lamp screws into the projector. Do  not put a metal piece or flammable object into the...

29
◆Replacing the lamp
1. Carefully turn the projector upside-down (a).
2. Loosen the screw (b) using a Phillips screwdriver (+), and 
remove the lamp cover (c).
3. Loosen the lamp screws (d) using a Phillips screwdriver (+).
4. Pull up the handle (e).
5. Pull out the lamp box by the handle while holding the  projector (f).
 Pull the lamp box out of the proj ector slowly. If it is pulled out 
quickly, the lamp may break  scattering glass fragments. 
 Do not spill liquid on the removed lamp box or place...

30
◆Attaching a commercially available lens filter
1. Carefully turn the projector upside-down.
2. Loosen the screw (a) using a Phillips screwdriver (+), and 
remove the stopper (b).
3. Place a lens filter (c).
4. Rotate the stopper 180° and reinsert it into its original  location (d).
5. Tighten up the screw (e) using a Phillips screwdriver (+).
Important
 Be sure to use a 67 mm lens filter for this projector.
 Not all 67 mm lens filters are compatible with this  projector.
◆ Attaching the lens cap...

31
◆Troubleshooting
Refer to the chart below when this projec tor does not function properly. If the problem  you are experiencing is not listed below or if the 
instructions do not help, stop using th e projector and contact your dealer.
No image appears on the screen.
ProblemSolution
Power can not be turned on.  Check whether the i ndicators are on or off and how they are lightning.
No image appears on the 
screen.  Check that the lens cap is removed.
 It may take about one minute for the lamp to...

32
Images are not displayed correctly.
“NO SIGNAL” is displayed.  Turn on the power of the connected device, or check whether there is something wrong with the connect ed 
device.
 Check whether the external device  outputs signals. (Check this especially when the external device is a 
notebook computer.)
 Check that the cable connected to  the external device isnt defective.
 Check that the projector is  connected to the external devi ce using the correct terminals.
 Check that the connected device...

33
Others
If the following problem occurs after the lamp is replaced, check the following first.
ProblemSolution
The exhaust vents emit warm 
air.  This air comes out after cooling the 
inside of the projector. It may feel hot, but this is not a malfunction.
The menu cant be used.  The microcomputers inside the  projector may be wrongly operating because of noise.
➜ Press the STANDBY/ON button to turn off the lamp  and unplug the power cable from the wall outlet.
Wait about 10 minutes, plug the  power...

34
This projector has two indicators, each of which shows the operation condition of the projector.
Refer to Troubleshooting for  additional indication signals.
◆Normal conditions
◆ Abnormal conditions
*1: When LAMP MODE of the SETUP menu is set to CINEMA.  When it is set to BRIGHT, this duration will be decreased.
*2: When LAMP MODE is set to BRIGHT, this  duration will be decreased to 2000 hours.
POWER STATUS CONDITION NOTE
Steady red Off
Stand-by.
Steady green Blinking green
Warming up period (about 1...

35
◆Projector specifications
The specifications and outside appe arance of the projector are subject to change without prior notice.
Type DLP™ projector
Model DPX-530
Display Technology 0.65-inch Single  chip DMD (Aspect ratio 16:9)
Pixel 1024 × 576 = 589824 pixels
Projection lens F 2.4  – 2.6 f= 23 – 27.6 mm
Light-source lamp 250 W
Image size (Projection distance) 40 min. to 275 max. (Pro jection distance 1.3 to 10 m)
Maximum number of display colors 16770000 (full-color display)
Maximum...

36
*1: When ASPECT in the INITIAL menu is set to DEFAULT.
*2: Unavailable with RGB-HV (5 line) sources.
◆Composite / S-video signal specifications
Signal mode Resolution 
(H × V)Horizontal frequency 
(kHz) Vertical frequency 
(Hz) Normal mode 
(H × V)*¹ Through mode 
(H × V)
TV60 – 15.73 59.94 1024 × 576 –
TV50 – 15.63 50.00 1024 × 576 –
◆ Component signal specifications
Signal mode Resolution 
(H × V)Horizontal frequency 
(kHz) Vertical frequency 
(Hz) Normal mode 
(H × V)*¹ Through mode 
(H × V)
480i...