Yamaha EF1000 Service Manual

ENGINE ENG 
JOB INSTRUCTION CHART 
Order Job name/Parts  name Oty Remarks 
Removal of Engine 
Remove the parts in order. 
Body cover/Fuel tank Refer to BODY COVER and 
FUEL TANK section. 
Muffler/Air filter Refer to MUFFLER and 
AIR FILTER section. 
1 Spark plug cap 1 
2 Oil  level  lead/Engine stop lead 1 
3 C.D.I. coupler 1 
4 Condenser lead 2 
5 DC rectifier coupler 1 
6 Main coil coupler 1 
7 Sub coil coupler 1 
8 Nut 4 
9 Earth lead 1 
10 Fuel tank breather hose 1 
11 Engine assembly 1 Reverse the...

.11111111 
CYLINDER HEAD COVER, CYLINDER HEAD, VALVE ENG B 
CYLINDER HEAD COVER,  CYLINDER HEAD, VALVE 
2 
5 j11 Nm (1.1 m•kg, 8.0 ft•lb) I 
10 Nm (1.0 m•kg, 7.2 ft•lb) 
2 
3-5  

.11111111 
CYLINDER HEAD COVER, CYLINDER HEAD, VALVE ENG [g 
JOB INSTRUCTION  CHART 
Order Job name/Parts name Qty Remarks 
Removal 
of cylinder  head cover, Remove the parts in order. 
cylinder  head and 
valve 
Recoil 
starter Refer to RECOIL  STARTER 
section in chapter 3. 
Air filter, Carburetor Refer to CARBURETOR 
section in chapter 3. 
1 Spark plug 1 
2 Bolt 4 
3 Cylinder head cover 1 
4 Gasket  1 
5 Air shround 1 
1 
6 Air shround 2  1 
7 Bolt 4 NOTE: Follow proper tightening 
sequence. 
8...

•llllull 
CYLINDER HEAD COVER, CYLINDER HEAD, VALVE ENG 8 
Intake Valve face: Exhaust Valve face: 
@ 
3-7 
CYLINDER HEAD INSPECTION 
1. Remove: 
•Carbon deposits 
Use rounded scraper. 
2. Measure: 
•Cylinder head warpage 
Exceeds allowable limit ---?Resurface. 
I~ 
Warpage Limit: 
0.1 mm (0.004 in) 
VALVE 
REMOVAL 
1. Remove: 
•Valve spring retainer CD 
•Vale spring ~ 
•Valve ® 
VALVE INSPECTION 
1. Inspect: 
•Valve length@ 
•Valve face diameter@ 
Valve length: 
Intake: 53.4 mm (2.10  in) 
Exhaust: 53.6...

CYLINDER HEAD COVER, CYLINDER HEAD,  VALVE ENG 
302-011 
3-8 
2. Inspect: 
•Valve stem diameter® 
Out of specification~Replace. 
Valve stem diameter: 
Standard: 
Intake: 5.0 mm (0.2 in) 
Exhaust: 5.0 mm (0.2 in) 
Limit: 
Intake: 4.89 mm (0.193 in) 
Exhaust: 4.87 mm (0.192 in) 
3. Measure: 
•Valve stem bend 
~ Valve stem bend limit: 
v A 0.01 mm (0.0004 in) 
Out of specification~Replace. 
VALVE SEAT INSPECTION 
1 .Measure: 
•Valve contact width ® 
Poor seating ~Looping. 
Out of specification~Replace....

•llllull 
CYLINDER HEAD COVER, CYLINDER HEAD, VALVE ENG 8 
302-017 
302-005 
3-9 
3. Rotate: 
•Valve 
Turn  until valve  and valve  seat are evenly 
polished,  then clean 
off compound. 
4. Repeat  above steps with fine compound and 
continue  lapping 
until valve face shows  a 
completely 
smooth surface uniformly. 
5. Eliminate: 
•Compound 
(from  valve face) 
6. 
Apply: 
•Mechanics bluing  dye (Dykem) CD 
(to valve  face and seat) 
7.  Rotate: 
•Valve 
Valve must make full seat contact indicat­
ed 
by...

.11111111 
CYLINDER HEAD COVER, CYLINDER HEAD,  VALVE ENG 8 
-~-® 
2 
4 
3-10 
2. Measure: 
•Valve spring tilt@ 
Use a square 
Out of specification~Replace. 
I~ 
lilt limit: 
0.8 mm (0.031 in) 
PUSH  ROD INSPECTION 
1. Measure: 
•Push rod bend 
Roll on V-block 
Exceeds bending limit~Replace. 
I~ 
Bend Limit: 
0.5 mm (0.02 in) 
CYLINDER HEAD INSTALLATION 
1. Install: 
•Cylinder head assembly 
NOTE: ________________________ ___ 
Follow proper tightening sequence. 
  Cylinder head bolt: 
~~ 11 Nm (1.1 m•kg,...

•llllull 
PISTON, CAMSHAFT, CRANKCASE, CRANKSHAFT ENG -
PISTON, CAMSHAFT, CRANKCASE,  CRANKSHAFT 
l 
m 
/ 
3-11 
l 
m 
2  

•llllull 
PISTON, CAMSHAFT, CRANKCASE,  CRANKSHAFT ENG 8 
JOB INSTRUCTION CHART 
Order Job name/Parts name Oty Remarks 
Removal of Piston,  Camshaft 
Remove the parts in order. 
Crankcase  and Crankshaft 
Generator,  Rotor 
Refer 
to the GENERATOR section. 
Engine Refer to the ENGINE section 
Flywheel Refer to the FLYWHEEL section. 
1 Bolt 7 NOTE: Follow proper tightening 
sequence. 
2 
Crankcase cover 1 
3  Gasket 1 
4 
Dowel pin 2 
5 Camshaft 1 NOTE: Be sure to align the camshaft 
gear mark with...

PISTON, CAMSHAFT, CRANKCASE,  CRANKSHAFT ENG 
3-13 
CRANKSHAFT  REMOVAL 
1. Remove: 
•Camshaft 
NOTE: ________________________ _ 
Remove the camshaft, facing the camshaft 
gear mark to the crankshaft gear mark. 
2. Remove: 
•Valve lifter 
CAUTION: 
Mark the valve lifters so that the exhaust 
and intake valve sides are not confused. 
CAMSHAFT AND VALVE LIFTER  INSPECTION 
1. Measure: 
•Cam lobes length® 
Use a micrometer. 
Out of specification---+Replace. 
Cam lobe length @: 
Standard: 20.5 mm (0.81 in)...