Yamaha Dtxtreme 3 Manual

Sampling Mode [SAMPLING]
Reference
DTXTREME III Owner’s Manual141
Drum Kit mode
Reference Song mode Click mode Trigger mode File mode Utility mode Chain mode Sampling mode
Explanations here apply to step 5 on page 140. 
From the display called up via the [SF5] SET END button 
on the [F3] TRIM display, you can set the tempo, beat 
(time signature) and measure for the audio data included in 
the User Voice, resulting that the End Point is automatically 
determined. If you are satisfied with the result...

Sampling Mode [SAMPLING]
Reference
142DTXTREME III Owner’s Manual
Sampling Jobs[F4] JOB
The Sampling Job lets you process and modify User Voices you have recorded. 14 Sampling Jobs are available. 
01: Normalize  06: Stereo to Mono  11: Delete
02: Time-Stretch  07: Loop-Remix  12: Delete All
03: Convert Pitch 08: Slice  13: Extract
04: Fade In/Out  09: Name  14: Optimize Memory
05: Convert Freq  10: Copy
1From the [F1] SELECT display, select the 
User Voice to which the Job is applied. 
2Press the [F4]...

Sampling Mode [SAMPLING]
Reference
DTXTREME III Owner’s Manual143
Drum Kit mode
Reference Song mode Click mode Trigger mode File mode Utility mode Chain mode Sampling mode
The explanations here apply to Steps 4 – 8 of “Basic Proce-
dure of the Sampling Jobs” on page 142. 
01: Normalize
This Job maximizes (normalizes) the overall level of the 
specified User Voice. This is useful for bringing up the vol-
ume of a User voice that was inadvertently recorded at a 
low level. 
1
Ratio
Determines the...

Sampling Mode [SAMPLING]
Reference
144DTXTREME III Owner’s Manual
04: Fade In/Out
This Job lets you create a fade-in for the starting portion of 
the User Voice and a fade-out for the ending section of the 
User Voice. 
1
Type (Fade Type)
Determines the type of level fade: fade-in or fade-out.
BLength
Determines the length of the fade-in or fade-out. When a fade-
in is selected, this parameter specifies the length of the fade 
starting at the specified Start point. When a fade-out is 
selected, this...

Sampling Mode [SAMPLING]
Reference
DTXTREME III Owner’s Manual145
08: Slice
This Job lets you divide the audio data included in the cur-
rent User Voice into separate “slices” and assign them to 
the different User Voices. 
This Job consists of two displays. The first display shown 
before executing the Slice operation lets you set how the 
audio data is divided while the second display shown after 
executing the Slice operation lets you assign the created 
“slice” to a different User Voice. 
The first...

Sampling Mode [SAMPLING]
Reference
146DTXTREME III Owner’s Manual
Reference
Drum Kit mode
Song mode
Click mode
Trigger mode
File mode
Utility mode
Chain mode
Sampling mode
«
 
ý
«
¨
 
Å


10: Copy
This Job lets you copy the data of one User Voice to 
another. 
1
User Voice bank and number as Source
BUser Voice bank and number as Destination
Determines the User Voice banks and numbers as source and 
destination. 
11: Delete
This Job lets you delete a specific User Voice from mem-
ory. 
1
User Voice...

 DTXTREME III Owner’s Manual 147 
Appendix
 
Appendix
 Optional DIMM Installation 
This section explains how to install DIMM memory modules to the DTXTREME III. 
 
The DTXTREME III does not necessarily support all com-
mercially available DIMMs. Yamaha cannot guarantee 
operation of DIMMs that you purchase.
Before purchasing DIMMs, please consult your Yamaha 
dealer, or an authorized Yamaha distributor (see list at end 
of the Owner’s Manual) for advice, or visit the following 
website:...

Optional DIMM Installation
Appendix
148DTXTREME III Owner’s Manual
1Turn the DTXTREME III power off, and dis-
connect the power cord.
2Turn over the DTXTREME III so you can 
have direct access to the underside. 
To protect the data dial and sliders from damage, place the 
DTXTREME III so the four corners are supported by some-
thing that provides sufficient support, such as magazines or 
cushions. Place supports at all four corners, taking care not to 
touch the Data dial and Sliders. 
3Remove the slot...

Optional DIMM Installation
Appendix
DTXTREME III Owner’s Manual149
Appendix
5Re-install the cover you removed in step 3, 
in reverse order.
6Check that the installed DIMMs are func-
tioning properly. 
Set the DTXTREME III right-side up, and connect the AC 
power adaptor to the DC IN jack of the DTXTREME III and 
an AC wall outlet. 
Turn on the power, go to the Sampling mode by pressing the 
[SAMPLING] button, then press the [SF6] INF button (page 
136). If the DIMMs have been installed properly, the...

Appendix
150DTXTREME III Owner’s Manual
Troubleshooting
No sound, even when the pad is hit. 
●Check whether or not the lamp of the TRIGGER INDICA-
TOR lights when you hit the pad. If not, make sure the 
pads and Drum triggers (Yamaha DT20, etc.) are con-
nected correctly to the input jacks of the DTXTREME III. 
(page 12) 
●Is the DTXTREME III properly connected to headphones 
or an external audio device such as an amplifier and 
speaker ? (page 19) 
●Is there a problem with the cable you are using ?...