Yamaha Dpx 830 User Manual

							37
Others
If the following problem occurs after the lamp is replaced, check the following first.
ProblemSolution
The exhaust vents emit warm 
air. This air comes out after cooling the inside of the projector. It may feel hot, but this is not a malfunction.
The menu can not be used.  The microcomputers inside the projector may be wrongly operating because of noise.
➜Press the STANDBY/ON button to turn off the lamp and unplug the power cable from the wall outlet.
Wait about 10 minutes, plug the power cable in, and try again.
“TEMPERATURE!!” is 
displayed. This indication appears when the ambient temperature rises high. When the ambient temperature stays 
high, the lamp goes out.
➜Eliminate any causes of the rise in the ambient temperature.
 This indication appears when the air intake or exhaust vent is blocked. When they are kept blocked, the 
lamp goes out.
➜Remove the objects blocking the air intake or exhaust vent.
The  mark appears. This mark appears when ineffective operation is carried out. This is not a product malfunction.
The remote control does not 
function easily or at all. Check that the battery is loaded in the remote control or the battery is not weak (see page 4).
 Check that the remote control sensor is not exposed to direct sunlight or fluorescent light.
 Use the remote control within its operation range (see page 7).
 Use the remote control at least 10 cm away from the projector.
Abnormal sound is heard.  Because the color wheel spins at a high speed, metallic sounds may be heard in rare occasions.
ProblemSolution
The projector does not turn 
on. Fit the lamp cover securely (see page 33).
 Reset the lamp operating time (see page 33).
The STATUS indicator 
blinks. Reset the lamp operating time (see page 33). 
						

							38
This projector has two indicators, each of which shows the operation condition of the projector.
Refer to Troubleshooting for additional indication signals.
◆Normal conditions
◆Abnormal conditions
*1: When LAMP MODE of the SETUP menu is set to CINEMA. 
*2: When LAMP MODE is set to STANDARD, this duration will be decreased to 2000 hours.
POWER STATUS CONDITION NOTE
Steady red Off
Stand-by.
Steady green Blinking green
Warming up period (about 1 minute).The STANDBY/ON button cannot be used 
until the STATUS indicator is steady green.
Steady green Steady green
The projector is ready.
Steady red Blinking green
Cooling down period (lasts under 2 minutes; normal when 
shutting down).Do not unplug the projector until the 
STATUS indicator is off.
POWER STATUS CONDITION SOLUTION
Steady green
or
Steady redBlinking orange
Abnormal temperature
 The ventilation grilles are clogged with dust or dirt.
 The room temperature is high. Clean the ventilation grilles.
 Relocate the projector to a cooler place.
 Remove any objects blocking the 
ventilation grilles.
Steady red Blinking green
Abnormal when it occurs except while shutting down. The 
protection circuit is working or the lamp is in an abnormal 
condition. Wait until the STATUS indicator goes out, 
then press the STANDBY/ON button.
 If the above solution is not effective, 
replace the lamp.
Steady green Blinking green/red
Lamp operation time warning. (Total lamp operation time 
reached 2250 hours*1 while the power was on.)Replace the lamp.
Change with a new lamp if this problem 
recurs.
Steady red Blinking red
Lamp operation time warning. (Total lamp operation time 
reached 2250 hours*1 while the power was off.)
Steady red Steady red
Lamp operation time warning. (Total lamp operation time 
reached 3000 hours*1, *2 while the power was off.)
Blinking 
green/redOff
The lamp cover isn’t closed. Close the cover correctly.
Blinking 
green/red    Steady or  Blinking
Abnormal. Contact your dealer.
STATUS indicator POWER indicator
STANDBY/ON button
Indicators14 
						

							39
◆Projector specifications
The specifications and outside appearance of the projector are subject to change without prior notice.
Type DLP™ projector
Model DPX-830
Display Technology 0.65-inch Single chip DMD
Pixel 1280 × 768 = 983040 pixels
Projection lens F 2.4 – 2.6 f= 23 – 27.6 mm
Light-source lamp 200 W
Image size (Projection distance) 40 min. to 275 max. (Projection distance 1.4 to 10.1 m (16:9 screen))
Maximum resolutionComputer signal Maximum resolution: 1280 x 1024 dots (Analog) / compressed
Panel resolution: 1280 × 768 dots
Video signal NTSC / PAL / SECAM / 4.43NTSC / PAL-M / PAL-N / PAL-60
Component signal 480i, 480p, 576i, 576p, 720p, 1080i
Panel resolution: 1280 × 768 dots
Input terminal [Signal type]
Analog RGB
Digital RGB
Video input
S-Video input
Component video input[Terminal type]
D-SUB 15P
HDMI
RCA × 1
S
RCA × 3, D-SUB 15P[Line]
1
1
1
1
2
Control terminal/
OthersUSB For service person
SERIAL RS-232C (8P): For service person
TRIGGER DC 12 V, Max.200 mA (Stereo mini jack)
Operating temperatures +41°F (+5°C) to +95°F (+35°C)
Rated voltageAC100 - 240 V, 50/60 Hz
Power consumption 280 W / 2.9 A
Power consumption (standby) 8 W
Dimensions 360 mm (W) × 102 mm (H) × 290 mm (D) *Not including protrusions.
Weight 3.9 kg
OthersS-video input Luminance signal: Vp-p=1.0 V 75 Ω (negative sync)
Chrominance signals: Vp-p=0.286 V 75 Ω (burst signal)
Video input Vp-p=1.0 V 75 Ω (negative sync)
Component video 
inputYCBCR: Vp-p=1.0 V 75 Ω (Y) (negative sync)
Vp-p=0.7 V 75 Ω (C
B, CR)
Analog RGB input RGB: Vp-p=0.7 V 75 Ω (negative sync)
HD: TTL-level (negative or positive polarity)
VD: TTL-level (negative or positive polarity)
Digital input (HDMI) HDMI interface (TMDS single link)
Specifications15 
						

							40
◆Composite / S-video signal specifications
Signal mode Resolution 
(H × V)Horizontal frequency 
(kHz)Vertical frequency 
(Hz)Default mode for 
16:9 screen 
(H × V)
*1
Default mode for  
4:3 screen 
(H × V)
*2
Through mode 
(H × V)
TV60 (525i) – 15.73 59.94 1280 × 720 1024 × 576 –
TV50 (625i) – 15.63 50.00 1280 × 720 1024 × 576 –
◆Component signal specifications
Signal mode Resolution 
(H × V)Horizontal frequency 
(kHz)Vertical frequency 
(Hz)Default mode for 
16:9 screen 
(H × V)
*1
Default mode for  
4:3 screen 
(H × V)
*2
Through mode 
(H × V)
480i (525i) – 15.73 59.94 1280 × 720 1024 × 576 –
576i (625i) – 15.63 50.00 1280 × 720 1024 × 576 –
480p (525p) – 31.47 59.94 1280 × 720 1024 × 576 –
576p (625p) – 31.25 50.00 1280 × 720 1024 × 576 –
720p 60 (750p 60) – 45.00 60.00 1280 × 720 1024 × 576 –
720p 50 (750p 50) – 37.50 50.00 1280 × 720 1024 × 576 –
1080i 60 (1125i 60) – 33.75 60.00 1280 × 720 1024 × 576 –
1080i 50 (1125i 50) – 28.13 50.00 1280 × 720 1024 × 576 –
◆Digital RGB / Component signal specifications
Signal mode Resolution 
(H × V)Horizontal frequency 
(kHz)Vertical frequency 
(Hz)Default mode for 
16:9 screen 
(H × V)
*1
Default mode for  
4:3 screen 
(H × V)
*2
Through mode 
(H × V)
480p (525p) – 31.47 59.94 1280 × 720 1024 × 576 –
576p (625p) – 31.25 50.00 1280 × 720 1024 × 576 –
720p 60 (750p 60) – 45.00 60.00 1280 × 720 1024 × 576 –
720p 50 (750p 50) – 37.50 50.00 1280 × 720 1024 × 576 –
1080i 60 (1125i 60) – 33.75 60.00 1280 × 720 1024 × 576 –
1080i 50 (1125i 50) – 28.13 50.00 1280 × 720 1024 × 576 –
VGA 60 640 × 480  31.47 59.94 960 × 720 1024 × 768 –
◆Analog RGB signal specifications
Signal mode Resolution 
(H × V)Horizontal frequency 
(kHz)Vertical frequency 
(Hz)Default mode for 
16:9 screen 
(H × V)
*1
Default mode for  
4:3 screen 
(H × V)
*2
Through mode 
(H × V)
576i (625i)
*3– 15.63 50.00 1280 × 720 1024 × 576 –
720p 60 (750p 60) – 45.00 60.00 1280 × 720 1024 × 576 –
720p 50 (750p 50) – 37.50 50.00 1280 × 720 1024 × 576 –
1080i 60 (1125i 60) – 33.75 60.00 1280 × 720 1024 × 576 –
1080i 50 (1125i 50) – 28.13 50.00 1280 × 720 1024 × 576 –
PC98 640 × 400 24.82 56.42 1152 × 720 1024 × 640 640 × 400
CGA70 640 × 400 31.47 70.09 1152 × 720 1024 × 640 640 × 400
CGA84 640 × 400 37.86 84.13 1152 × 720 1024 × 640 640 × 400
VGA60 640 × 480 31.47 59.94 960 × 720 1024 × 768 640 × 480
VGA72 640 × 480 37.86 72.81 960 × 720 1024 × 768 640 × 480
VGA75 640 × 480 37.50 75.00 960 × 720 1024 × 768 640 × 480
VGA85 640 × 480 43.27 85.01 960 × 720 1024 × 768 640 × 480
SVGA56 800 × 600 35.16 56.25 960 × 720 1024 × 768 800 × 600
SVGA60 800 × 600 37.88 60.32 960 × 720 1024 × 768 800 × 600
SVGA72 800 × 600 48.08 72.19 960 × 720 1024 × 768 800 × 600
SVGA75 800 × 600 46.88 75.00 960 × 720 1024 × 768 800 × 600
SVGA85 800 × 600 53.67 85.06 960 × 720 1024 × 768 800 × 600
XGA60 1024 × 768 48.36 60.00 960 × 720 1024 × 768
*4
XGA70 1024 × 768 56.48 70.07 960 × 720 1024 × 768*4
XGA75 1024 × 768 60.02 75.03 960 × 720 1024 × 768*4
XGA85 1024 × 768 68.68 85.00 960 × 720 1024 × 768*4
MAC13 640 × 480 35.00 66.67 960 × 720 1024 × 768 640 × 480
MAC16 832 × 624 49.72 74.55 960 × 720 1024 × 768 832 × 624
MAC19 1024 × 768 60.24 75.02 960 × 720 1024 × 768
*4
SXGA60 1280 × 1024 60.02 63.98 900 × 720 960 × 768*4 
						

							41
*1: When ASPECT in the INITIAL menu is set to DEFAULT, and SCREEN ASPECT in the SETUP menu is set to 16:9.
*2: When ASPECT in the INITIAL menu is set to DEFAULT, and SCREEN ASPECT in the SETUP menu is set to 4:3.
*3: Available with RGB-CS (4 line) sources from SCART terminal.
*4: Same resolution as the DEFAUL mode depending on the each SCREEN ASPECT.
Important
 This projector can recognize 1280 × 768 pixels as the maximum resolution, however, it is programmed to recognize 1280 × 
720 or 1024 × 768 pixels as the normal resolution depending on the screen aspect.
 If the resolution and frequency of your computer are not shown on the table, find the compatible resolution and frequency by 
changing the resolution of your computer.
 In the case of XGA, the right side of the image may not appear. In this case, adjust TRACKING in the SIGNAL menu.
 TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are input to the VIDEO or S-VIDEO signal, 
the signal mode is indicated as TV60 or TV50. When they are input to the COMPONENT terminal, the signal mode is 
indicated as 480i or 576i.
 This projector cannot be connected to other equipment via an RGB-CS (4 line) connection.
Connectors
SERIAL (8-pin) D-SUB (Mini D-SUB 15-pin) HDMI (HDMI - 19 pin)
◆Dimension drawings
Pin No. Name I / O
1TXDIN
2––
3––
4 GND –
5––
6––
7 RXD OUT
8––
1
352
68
Pin No. Spec. Pin No. Spec.
1 R(RED) / CR 9 –
2 G(GREEN) / Y 10 GND
3 B(BLUE) / CB 11 GND
4 GND 12 DDC Data
5 GND 13 HD/CS
6 GND 14 VD
7 GND 15 DDC Clock
8 GND
1 5
116 10
15
Pin No. Spec. Pin No. Spec.
1 TMDS Data2+ 11 TMDS Clock 
Shield
2TMDS Data2 
Shield12 TMDS Clock-
3 TMDS Data2- 13 -
4 TMDS Data1+ 14 -
5TMDS Data1 
Shield15 SCL
6 TMDS Data1- 16 SDA
7 TMDS Data0+ 17 DDCGround
8 TMDS Data02 
Shield18 +5 V Power
9 TMDS Data0- 19 Hot Plug Detect
10 TMDS Clock+
191
2
18
290
69
360
102
2
(Unit: mm) 
						

							DPX-830
Digital Cinema Projector
Projecteur Cineme Numerique
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES BRUKSANVISNING
GEBRUIKSAANWIJZINGYAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADAYAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANYYAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCEYAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLANDYAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDENYAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
© 2006                                         All rights reserved.
DPX-830
Printed in Japan     871D460A20
01EN_DPX-830_EX-cv_new.fm  Page 1  Monday, December 26, 2005  8:21 PM