Yamaha Dpx 1 User Manual
Have a look at the manual Yamaha Dpx 1 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 255 Yamaha manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
E-15 English MENU MENU Menu structure It is necessary to make various settings on the menu so that this unit can achieve the best performance. The menu has a three-level hierarchy; menu group, menu item, and submenu for some menu items. Listed below are the four menu groups. 1 To adjust the image quality. Available items depend on the type of input signal. 2 To make settings for the connected input signal. Available items depend on the type of input signal. 3 To make your own initial setting for several menu items. 4 To make settings for installation, screen aspect, key stone effect correction and so on. Each menu group described above consists of the following items. The parameters for these items can be adjusted as you wish by following the menu operation procedures described from page 18. S means that the item has a submenu. 1 ........... Adjustment cannot be made without any input signal. Input signal Video/Component/ RGB TV Video/Component/ RGB Video/Component/ RGB Video/Component/ RGB Video/Component/ RGB Video Video Component Video/Component/ RGB Video/Component/ RGB Video/Component/ RGBMenu itemBLACK LEVEL Adjusts the level of blackness while maintaining the peak white brightness. CONTRAST The ratio of light versus dark. If increased too high, the whole image becomes light and the white portion of the image tends to be saturated. If decreased too low, the whole image becomes dark and flat. BRIGHTNESS Controls the total brightness of an image. When adjusted too high, the black portion of the image becomes grayish and the white portion of the image tends to be saturated. When adjusted too low, the entire image becomes darker. GAMMA TRIM Adjusts the response of the color gradation and gray-scale of the image. There are five patterns available. Select the appropriate pattern depending on the content to be projected. SHARPNESS Adjusts the clearness of the image edges. The higher value creates clearer edges. The lower value creates a softer image with the less noise element. HUE Adjusts the hue. When adjusted to the negative direction, red increases. When adjusted to the positive direction, blue increases. SATURATION Adjusts the depth of a color. When adjusted to the negative direction, the color becomes lighter. When adjusted to the positive direction, the color becomes deeper. COLOR BOOST Boosts the color saturation. The higher value makes the color tends to be saturated and becomes deeper. COLOR TEMP Adjusts the color of the image to be projected. The higher setting adds more blue and the lower setting adds more red. Select the appropriate setting depending on the content to be projected. WHITE BALANCE SFine-adjusts the balance of each color (R, G, B). CONTRAST (R, G, B) BRIGHTNESS (R, G, B) WHITE BOOST Optically adjusts the luster of the white part of the projected image.Adjustment range –64 to 32 –128 to 127 –128 to 127 A/B/C/D/E 1 to 5 –128 to 127 –128 to 127 0 to 127 LOW/MID-L/MID/HIGH 50% to 124% –12.4% to 12.4% 0 to 10 The three menu items described above are to adjust the input and output characteristics for the image brightness of the luminance signal. The graphs below show how these items can be adjusted. BRIGHTNESS White Black White Input signalCONTRAST White Black White Input signal BLACK LEVEL White Black White Output image Input signal
E-16 Menu structure Input signal Video/Component/RGB Video/Component Video/Component Video Video/Component Video Video/Component RGB RGB RGB RGB RGB 2 ......... Adjustment cannot be made without any input signal. Menu item ASPECT SSets the aspect ratio of displaying the image on the screen. “AUTO” automatically switches to the most appropriate mode. “NORMAL” (THROUGH) projects the image as the input signal is sent. “SQUEEZE” desqueezes the squeezed image. “ZOOM” projects the image scaled up with a certain ratio. “ZOOM -SUBTITLE-” displays the subtitle. “THROUGH -SQUEEZE-” displays the image with its width scaled up. Available items depend on the “SCREEN ASPECT” setting and the type of input signals. “ZOOM -SUBTITLE-” has further items to be adjusted SUBTITLE AREA: adjusts the subtitle area. V SCROLL: adjusts the subtitle position by vertically scrolling the projected image. SUBTITLE MASK Darkens the brightness of the characters in the subtitles when playing the film in letterbox with subtitles (except for HDTV). MASK POSITION Changes the effective height for the “SUBTITLE MASK” adjustment (except for HDTV). 3D Y/C SEPARATION Suppresses the rainbow-like color crossing the image of fine vertical stripes or annoying dot interference on the image edge when the video signal is input. This adjustment is available only for the composite signal in NTSC mode. NOISE REDUCTION Effectively reduces the noise included in the luminance signal and color signal by digital processing when playing the source with a relatively large amount of noise in order to create a more vivid image (interlaced signal only, except for HDTV). VIDEO TYPE Selects VCR when playing video tapes in order to ensure synchronization, and selects DVD when playing other sources. SETUP LEVEL Adjusts the black level difference of the image signal. Select 0% for a signal with no difference from the pedestal level, and 7.5% for a signal with higher black level. DOT PHASE Fine-adjusts the phase of the RGB signal input from the computer for clearest display of the characters and lines of the image (except for DVI). SIZE H Adjusts the horizontal size of the projected image (except for DVI). SHIFT H Adjusts the horizontal position of the projected image (except for DVI). SHIFT V Adjusts the vertical position of the projected image (except for DVI). SIGNAL STATUS Displays the resolution and sync. frequency of the input signal. Choice/adjustment range AUTO/NORMAL/ SQUEEZE/ZOOM/ZOOM -SUBTITLE- S(SUBTITLE AREA, V SCROLL)/THROUGH/ THROUGH -SQUEEZE- 0 to 99 0 to 99 OFF/ON –10 to 10 ON/OFF OFF/1/2/3 DVD/VCR 0%/7.5% 0 to 31 –2047 to 2048 0 to 100 0 to 100 — 100 0 % Image signal Pedestal level Black level
E-17 English MENU Menu structure 4 Menu item INSTALLATION SThere are four methods to install this unit; tabletop or on-ceiling for front or rear projection. The image can be inverted or rotated according to the setting for the installation method. SCREEN ASPECT Selects 4:3 or 16:9 depending on the screen to be used. If 16:9 is selected, vertical adjustment of the image can be made by changing the value of the item “DIGITAL LENS SHIFT”. And automatically makes an adjustment to project the 4:3 input signal without losing any part of it off screen. * DIGITAL LENS SHIFT The image on the screen can be vertically adjusted within a certain range by digital processing. h moves the image upward and g downward. This adjustment is available only when the screen aspect ratio is set to 16:9. KEYSTONE If this unit projects on a the screen with some elevation or depression angle at its installation, the image on the screen is distorted into a trapezoid. This parameter electrically corrects the distortion. Increase the value when the upper part of the image is wider. Decrease the value when the lower part if the image is wider. KEYSTONE MODE There are two modes; “FULL” that corrects the key stone effect without changing the vertical length of the image, and “NORMAL” that makes vertical correction by shifting the bottom at the same time. Select the appropriate mode to make correction depending on your installation. R/C SENSOR SSets the remote control sensor to be used. This unit has its remote control sensor in two locations: at the front and the rear.Choice/adjustment range FRONT/TABLE, FRONT/CEILING, REAR/TABLE, REAR/CEILING 4:3/16:9* –96 to 96 –128 to 127 NORMAL/FULL FRONT&REAR/FRONT/REAR 3 Menu item COLOR SYSTEM SSelects the color system when the video signal is input among NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM. AUTO should normally be selected so that the appropriate color system can be automatically selected depending on the input signal. INPUT A SIGNAL SSelects the type of input signal sent to the INPUT A jacks. INPUT B SIGNAL SSelects the type of input signal sent to the INPUT B jacks. LANGUAGE SSelects the language used on the menu. POWER SAVING When no signal is received at the input jacks for longer than 15 minutes, this unit automatically turns off the lamp and enters the standby mode if ON is selected. LAMP RUNNING TIME SDisplays the total lamp running time. The lamp running time can be reset on the submenu. RESET SResets all parameters on the menu or parameters in the memory to the factory settings.Choice AUTO/NTSC/NTSC4.43/PAL/PAL-M/PAL-N/ PAL60/SECAM COMPONENT/RGB PC/RGB TV COMPONENT/RGB PC/RGB TV /ENGLISH/DEUTSCH/ESPAÑOL/ FRANÇAIS/ITALIANO/ OFF/ON — ALL SETTINGS/ALL MEMORIES/ CURRENT MEMORY 1Normal correction This correction shifts the bottom of the projected image to correct the horizontal distortion. When the upper part of the image is wider than the lower part, increase the value to the positive (+) direction. When the lower part of the image is wider than the upper part, decrease the value to the negative (–) direction.2Full correction This correction adjusts the horizontal distortion without changing the vertical length of the projected image. When the upper part of the image is wider than the lower part, increase the value to the positive (+) direction. When the lower part of the image is wider than the upper part, decrease the value to the negative (–) direction.
E-18 Menu screen and operating buttons This section provides you with general information about the menu screen and operating buttons on the remote control and this unit’s control panel for easier operation. Please read it carefully before starting to operate the menu. Menu operation MOVE MENU WINDOW IMAGESIGNALINITIALSETUP COLOR SYSTEMAUTO COMPONENT RGB PC ENGLISH 2H. INPUT A SIGNAL INPUT B SIGNAL LANGUAGE POWER SAVING LAMP RUNNING TIME RESET ESCAPE: EXIT MEMORY1 VIDEO OFFONLANGUAGE ESPAÑOL FRANÇAIS ITALIANO DEUTSCH ENGLISH MOVE MENU WINDOW Menu group Menu item Help message Memory setting number Input signalSubmenu parameter 1MENU button Opens or closes the menu. 2Cursor buttons +/– (for side-to-side movements) •Select a menu group. •Open or closes a submenu. •Select or changes a setting. h/g (for up and down movements) •Select a menu item. •Select or changes a setting. 3SELECT button •Opens a submenu. •Confirms a new setting when adjusting “COLOR SYS- TEM”, “INPUT A SIGNAL”, “INPUT B SIGNAL”, or R/ C SENSOR”. •Opens a one-touch image menu when the menu screen has not been opened. 4MEMORY 1 to 6 button (Remote control only) Selects a memory setting number. 5RESET button (Remote control only) Resets the parameter setting to the factory setting. Items without factory settings cannot be reset. 6ESCAPE button •Returns the cursor to the menu group hierarchy from the menu item hierarchy. •Returns to the menu from the MOVE MENU WINDOW. •Closes the submenu. •Closes the menu when the cursor is on one of the menu groups. •Closes the one-touch image menu. The menu has a three-level hierarchy: menu group, menu item, and submenu for some menu items. PATTERNMENUINPUTESCAPESELECT 16 2 3 AUTO ESCAPE SELECT ASPECT RESET STILL INPUT MEMORYHIDE S VIDEOA 123 456DVI VIDEOBD4 INPUT MENU PAT TPATTERNSTANDBY/ON 1 2 3 4 6 5 Parameter Submenu mark
E-19 English MENU Menu operation AUTO ESCAPE SELECT ASPECT RESET STILL HIDE INPUT MENU PAT TPATTERNSTANDBY/ON 5 3, 5 41, 6 2, 4STANDBY/ONPATTERNMENUINPUTLAMP/COVERTEMP/FA N 24PESCAPESELECT 2, 4 5 3, 5 1, 6 Basic menu operation To ensure proper projection, start with setting and adjustment for the menu group “SETUP”. 1.Press the MENU button to open the menu. The previous menu screen opens if menu operation has already been performed. 2.Press the + or – button to select a menu group. MENU MENU Remote controlor Control panel MOVE MENU WINDOW IMAGESIGNALINITIALSETUP BLACK LEVEL 0 CONTRAST 0 BRIGHTNESS 0 HUE 0 SATURATION COLOR BOOST GAMMA TRIM MEMORY1 VIDEO ABCDE 12345 SHARPNESS 0 0 MOVE MENU WINDOW IMAGESIGNALINITIALSETUP INSTALLATIONFRONT/TABLE FRONT&REAR SCREEN ASPECT KEYSTONE 0 KEYSTONE MODE R/C SENSOR 4:316:9 NORMALFULL MEMORY1 VIDEO SELECT Remote controlor Control panel 3.Press the g button to enter the menu item hierarchy. Then select an item to be adjusted by pressing the h or g button. 4.Select or change the parameter by pressing the + or – button. SELECT IMAGESIGNALINITIALSETUP INSTALLATIONFRONT/TABLE FRONT&REAR SCREEN ASPECT KEYSTONE 0 KEYSTONE MODE R/C SENSOR 4:316:9 NORMALFULL MEMORY1 VIDEO Remote controlor Control panel IMAGESIGNALINITIALSETUP INSTALLATIONFRONT/TABLE FRONT&REAR SCREEN ASPECT KEYSTONE 0 KEYSTONE MODE R/C SENSOR DIGITAL LENS SHIFT 4:316:9 NORMALFULL MEMORY1 VIDEO SELECT Remote controlor Control panel
E-20 Menu operation Some items are adjusted by increasing or decreasing the value on the scale, and others by selecting a number or a word. Press the RESET button to reset the parameter to the factory setting. (Items without a factory setting cannot be reset.) 5.Press the h or g button to move the cursor to the next item. First return to the menu group by pressing the ESCAPE or h button if the next item belongs to the another menu group. Then follow the previous steps 2—4 to continue menu setting. 6.Press the MENU button to close the menu when setting has been completed. KEYSTONE 0 KEYSTONE MODENORMALFULL SELECT Remote controlor Control panel MENU MENU Remote controlor Control panel Submenu Following is a list of the menu items that have a submenu. Submenu operation varies according to the menu item selected. Follow the steps of the applicable submenu operation group. Menu items with a submenu Submenu operation group C A B B B A D D A A B Operation group A: Press the SELECT or + button to open the submenu. Select the desired parameter by pressing the h or g button, and then press the ESCAPE or – button to close the submenu. Operation group B: Press the SELECT or + button to open the submenu. Select the desired parameter by pressing the h or g button, and then confirm the new setting by pressing the SELECT button. After the setting has been confirmed, press the ESCAPE or – button to close the submenu. Operation group C: Press the SELECT or + button to open the submenu. Select the submenu item by pressing the h or g button, and then change the parameter by pressing the h or g button. It is not necessary to confirm the new setting. Operation group D: Press the SELECT or + button to open the submenu, which is in the form of messages. Perform menu operation by following the direction in the message. The submenu for this group is explained in the section on pages 22 and 23. -Exception- * When the menu item “SCREEN ASPECT” in the menu group “SETUP” is set to “16:9” If “ZOOM -SUBTITLE-” is selected in the submenu for “ASPECT”, there is an additional menu to make your desired setting. Press the SELECT button to open the additional menu. There are two items, “SUBTITLE AREA” and “V SCROLL”. Select the item to be adjusted by pressing the h or g button. Set the desired value by pressing the + or – button. Press the ESCAPE button to close the additional menu. Menu group IMAGE SIGNAL INITIAL SETUPMenu item WHITE BALANCE ASPECT* COLOR SYSTEM INPUT A SIGNAL INPUT B SIGNAL LANGUAGE LAMP RUNNING TIME RESET INSTALLATION DIGITAL LENS SHIFT R/C SENSOR
E-21 English MENU Menu operation Basic submenu operation [Operation groups A and B] 1.Select the menu item to be adjusted by following steps 1—3 in “Basic menu operation”. The submenu mark “ ” appears on the right side of the item. 2.Press the SELECT or + button to open the submenu. IMAGESIGNALINITIALSETUP COLOR SYSTEMAUTO COMPONENT RGB PC ENGLISH 2H. INPUT A SIGNAL INPUT B SIGNAL LANGUAGE POWER SAVING LAMP RUNNING TIME RESET MEMORY1 VIDEO OFFON SELECT SELECT Remote controlor Control panel IMAGESIGNALINITIALSETUP ENGLISH DEUTSCH ESPAÑOL FRANÇAIS ITALIANO LANGUAGE ESCAPE: EXIT MEMORY1 VIDEO 3.Select the submenu parameter by pressing the h or g button. Press the RESET button to reset the parameter to the factory setting. (Items without a factory setting cannot be reset.) When setting “COLOR SYSTEM”, “INPUT A SIGNAL”, “INPUT B SIGNAL”, or “R/C SENSOR”, the following step [Operation group B only] is necessary. [Operation group B only] Press the SELECT button to confirm the new setting and close the submenu. Setting cannot be changed for the above items if not confirmed by the SELECT button. To reset the parameter to the factory setting, press the RESET button when the submenu has been opened. 4.Press the MENU button to close the menu. Press the ESCAPE or – button to return to the previous screen if continuing to adjust settings. SELECT Remote controlor Control panel ENGLISH DEUTSCH ESPAÑOL FRANÇAIS ITALIANO VIDEO BILD SIGNALEINST.AUFST. SPRACHE SPEICHER1 ESCAPE: VERLASSEN SELECT SELECT Remote controlor Control panel MENU MENU Remote controlor Control panel
E-22 IMAGESIGNALINITIALSETUP COLOR SYSTEMAUTO COMPONENT RGB PC ENGLISH 2H. INPUT A SIGNAL INPUT B SIGNAL LANGUAGE POWER SAVING LAMP RUNNING TIME RESET MEMORY1 VIDEO OFFON IMAGESIGNALINITIALSETUP PRESS ”SELECT” TO RESET LAMP RUNNING TIME ON ”YES”. ESCAPE: EXIT MEMORY1 VIDEO LAMP RUNNING TIME 2H.NO YES Menu operation Submenu operation—“WHITE BALANCE” [Operation group C] 1.Select the menu item “WHITE BALANCE” in the menu group “IMAGE” by following steps 1—3 in “Basic menu operation”. The submenu mark “ ” appears on the right side of the item. 2.Press the SELECT or + button to open the submenu. 3.Select the submenu item by pressing the h or g button. IMAGESIGNALINITIALSETUP WHITE BALANCE WHITE BOOST 0 MEMORY1 VIDEO COLOR TEMPLOWMID-LMIDHIGH IMAGESIGNALINITIALSETUP WHITE BALANCE CONTRAST R 100% MEMORY1 VIDEO CONTRAST G 100% CONTRAST B 100% BRIGHTNESS R 0% BRIGHTNESS G 0% BRIGHTNESS B 0% ESCAPE: EXIT 4.Select the value by pressing the + or – button. Press the RESET button to reset the parameter to the factory setting. 5.Press the MENU button to close the menu. Press the ESCAPE button to return to the previous screen if continuing to adjust settings. The – button does not close the submenu to return to the previous screen for this parameter. Submenu operation—“LAMP RUNNING TIME” [Operation group D] 1.Select the menu item “LAMP RUNNING TIME” in the menu group “INITIAL” by following steps 1–3 in “Basic menu operation”. The submenu mark “ ” appears on the right side of the item. 2.Press the SELECT or + button to open the confirma- tion message screen. IMAGESIGNALINITIALSETUP WHITE BALANCE CONTRAST R 100% MEMORY1 VIDEO CONTRAST G 100% CONTRAST B 100% BRIGHTNESS R 0% BRIGHTNESS G 0% BRIGHTNESS B 0% ESCAPE: EXIT IMAGESIGNALINITIALSETUP WHITE BALANCE CONTRAST R 100% MEMORY1 VIDEO CONTRAST G 100% CONTRAST B 80% BRIGHTNESS R 0% BRIGHTNESS G 0% BRIGHTNESS B 0% ESCAPE: EXIT
E-23 English MENU 3.Select the submenu item to be reset by pressing the h or g button. 4.Press the SELECT or + button to open the confirma- tion message screen. 5.Press the SELECT button to reset to the factory setting. The menu closes after the parameters have been reset to the factory settings. Menu operation IMAGESIGNALINITIALSETUP ESCAPE: EXIT MEMORY1 VIDEO LAMP RUNNING TIME 2H.NO YES PRESS ”SELECT” TO RESET LAMP RUNNING TIME ON ”YES”. 3.Select “YES” by pressing the h or g button, and then press the SELECT button to reset the lamp running time to 0. 4.Press the MENU button to close the menu. Submenu operation—“RESET” [Operation group D] 1. Select the menu item “RESET” in the menu group “INITIAL” by following steps 1—3 in “Basic menu operation”. The submenu mark “ ” appears on the right side of the item. 2.Press the SELECT or + button to open the submenu. IMAGESIGNALINITIALSETUP COLOR SYSTEMAUTO COMPONENT RGB PC ENGLISH 2H. INPUT A SIGNAL INPUT B SIGNAL LANGUAGE POWER SAVING LAMP RUNNING TIME RESET MEMORY1 VIDEO OFFON IMAGESIGNALINITIALSETUP RESET CURRENT MEMORY ALL MEMORIES ALL SETTINGS ESCAPE: EXIT MEMORY1 VIDEO IMAGESIGNALINITIALSETUP RESET CURRENT MEMORY ALL MEMORIES ALL SETTINGS ESCAPE: EXIT MEMORY1 VIDEO IMAGESIGNALINITIALSETUP PRESS ”SELECT” TO RESET TO FACTORY SETTINGS. ESCAPE: EXIT MEMORY1 VIDEO
E-24 Menu operation One-touch image menu 1. Press the SELECT button to open the one-touch image menu when the menu has not been opened. The image menu items appear at the bottom of the screen one after another. The previous parameter appears once menu operation has been performed. The displayed item turns off if no operation is performed within five seconds. 2.Select the item to be adjusted by pressing the h and g button. 3.Select the value by pressing the + or – button. Press the RESET button to reset the parameter to the factory setting. 4.Press the SELECT or ESCAPE button to close the one-touch menu. SELECT SELECT Remote controlor Control panel BLACK LEVEL 0 SELECT Remote controlor Control panel CONTRAST 0 CONTRAST 100 SELECT Remote controlor Control panel ESCAPESELECTESCAPE SELECT Remote controlor Control panel Changing the menu location 1. Press the ESCAPE or h button to return the cursor to the menu group. 2.Press the h button to enter the “MOVE MENU WIN- DOW”. 3.Change the location of the menu by pressing the +, –, h, or g button. 4.Press the ESCAPE button to return to the menu after the location has been decided. ESCAPE SELECTESCAPE Remote controlor Control panel MOVE MENU WINDOW IMAGESIGNALINITIALSETUP INSTALLATIONFRONT/TABLE FRONT&REAR SCREEN ASPECT KEYSTONE 0 KEYSTONE MODE R/C SENSOR 4:316:9 NORMALFULL MEMORY1 VIDEO MOVE MENU WINDOW SETUP ESCAPE: EXIT MEMORY1 VIDEO SELECT Remote controlor Control panel SELECT Remote controlor Control panel ESCAPE ESCAPE Remote controlor Control panel