Yamaha Clavinova Cvp 5 Manual

CVP-509/505: Keyboard Stand Assembly
CVP-509/505/503/501 Owner’s Manual  111
3
CVP-509/505: Keyboard Stand 
Assembly
CAUTION• Assemble the stand on a flat floor with ample space.
• Be careful not to confuse parts, and be sure to install all parts i\
n the correct direc-
tion. Please assemble in accordance with the sequence given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated below. Use of incorrect screws  can cause damage.
• Be sure...

112 CVP-509/505/503/501 Owner’s Manual
3
CVP-509/505: Keyboard Stand Assembly
3Attach B and C to A.
1Align parts B and A so that the protrusion fits into the hole.
2 Fix the bottom surface of the unit using two long screws.
3 Fix the side of the speaker box using two short screws.
If the screw holes do not align, loosen the other screws and adjust 
the position of B.
4 Fix C in the same way.
4Fix E to D using two short screws.
5Attach D to A.
1Fix D to the bottom surface of A using two short screws.
If...

CVP-509/505/503/501 Owner’s Manual113
3
CVP-509/505: Keyboard Stand Assembly
8Connect the pedal cord.
9Attach G using two screws for the cover.
10Set the voltage selector and connect the 
power cord.
Voltage Selector
Before connecting the AC power cord, check the setting of the 
voltage selector which is provided in some areas. To set the selec-
tor for 110V, 127V, 220V or 240V main voltages, use a “minus” 
screwdriver to rotate the selector dial so that the correct voltage 
for your region appears next...

114 CVP-509/505/503/501 Owner’s Manual
CVP-503: Keyboard Stand Assembly
3
CVP-503: Keyboard Stand 
Assembly
CAUTION• Assemble the stand on a hard and flat floor with ample space.
• Be careful not to confuse parts, and be sure to install all parts i\
n the correct direc-tion. Please assemble in accordance with the sequence given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated below. Use of incorrect screws  can cause damage.
• Be sure to...

CVP-509/505/503/501 Owner’s Manual115
3
CVP-503: Keyboard Stand Assembly
5Fix A.
1Center A to produce equal clearance on the left and right sides.
2 Use 6 x 16 mm short screws to secure A from the front.
6Connect the pedal cord.
7Set the voltage selector and connect the power 
cord.
Voltage Selector
Before connecting the AC power cord, check the setting of the volt-
age selector which is provided in some areas. To set the selector for 
110V, 127V, 220V or 240V main voltages, use a “minus” screwdriver 
to...

116 CVP-509/505/503/501 Owner’s Manual
CVP-501: Keyboard Stand Assembly
3
CVP-501: Keyboard Stand 
Assembly
CAUTION• Assemble the stand on a hard and flat floor with ample space.
• Be careful not to confuse parts, and be sure to install all parts i\
n the correct direc-tion. Please assemble in accordance with the sequence given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated below. Use of incorrect screws  can cause damage.
• Be sure to...

CVP-509/505/503/501 Owner’s Manual117
3
CVP-501: Keyboard Stand Assembly
5Mount A.
Be sure to place your hands at least 10 cm from either end of A when 
positioning it.
6Secure A.
7Connect the pedal cord.
8Set the voltage selector and connect the power 
cord.
9Set the adjuster.
Rotate the adjuster until it comes in firm contact with the floor su\
r-
face.
CAUTION• Fingers can become pinched between A and rear or side pan-els, be extra careful so as not to drop A.
• Do not hold the keyboard in any position...

118 CVP-509/505/503/501 Owner’s Manual
Installing the Floppy Disk Drive (Optional) (CVP-509/505)
3
Installing the Floppy Disk Drive 
(Optional) (CVP-509/505)
The floppy disk drive can be installed to the bottom of the instrument by using the included\
 floppy disk drive case 
and screws. 
For a list of optional floppy disk drives available for this instrument, see “Optional Accessories” (page 127).
1Remove the three backing papers from the 
adhesive tape in the case, and fit the floppy 
disk drive into the...

Handling the Floppy Disk Drive (FDD) and Floppy Disks
CVP-509/505/503/501 Owner’s Manual  119
3
Handling the Floppy Disk Drive 
(FDD) and Floppy Disks
(The floppy disk drive is optional. For instructions on installing the floppy disk drive, see page 127.)
The floppy disk drive lets you save original data you’ve created on the instrument to floppy disk, and allows you to 
load data from floppy disk to the instrument.
Be sure to handle floppy disks and treat the disk drive with care. Follow the important...

120 CVP-509/505/503/501 Owner’s Manual
Troubleshooting
Troubleshooting
Overall
A click or pop is heard when the power is turned on or off. Electrical current is being applied to the instrument. This is normal.
Noise is heard from the instrument’s speakers. Noise may be heard if a mobile phone is used near the instrument or 
if the phone is ringing. Turn off the mobile phone, or use it further 
aw ay from the instrument.
In the LCD display, there are some black points (unlit) or white 
points (always...