Xerox Projector Dp 1015 User Manual

							User Controls
16Xerox DP1015 User’s Guide
User Controls
Panel Control and Remote Control
Panel Control
Control Description
Indicator (LED)Flashes during power startup; remains steady 
when projector is ready; flashes rapidly if lamp 
overheats or fan fails.
 PowerTurns projector power on and off. See 
“Powering On/Off the Projector” on page 12 for 
the specific power on/off sequences.
Auto/EnterOSD menus displayed: Confirms your 
selection of items on the menus. 
OSD menus not displayed: Synchronizes the 
projector with the connected components to 
produce the optimum projected image.
MenuOpens the On-Screen Display (OSD) menus. 
To close the OSD, press the Menu button 
again.
Directional Selection 
Keys 
(     )OSD menus displayed: Selects items or 
adjusts settings of items. 
OSD menus not displayed, and you have 
multiple video sources connected: Press the 
   keys to select among the sources and 
pick the one to display its image. 
						

							Xerox DP1015 User’s Guide17
User Controls
Remote Control
Button Description
Laser PointerPress to activate a laser beam for use as a 
pointer. Warning—Do not look into the laser 
beam or shine it into others’ eyes when using 
the remote control as a laser pointer. Laser 
light can seriously damage eyes.
Freeze/Esc/LOSD menus displayed: Exits the OSD menus.
OSD menus not displayed: Holds the current 
image still on the screen. Press again to 
resume the action. Only for use with 
presentations, not video.
Remote used as a mouse: Left mouse button.
Enter/ROSD menus displayed: Selects OSD option.
Remote used as a mouse: Right mouse button.
Directional Selection 
Keys (     )OSD menus displayed: Selects items or 
adjusts settings of items. 
OSD menus not displayed, and you have 
multiple video sources connected: Press the 
   keys to select among the sources and 
pick the one to display its image.
Remote used as a mouse: Moves the mouse 
cursor.
Zoom active: Moves the zoomed image.
Laser Pointer Button 
						

							User Controls
18Xerox DP1015 User’s Guide
Pg.UpZooms in (enlarges) the image.
Remote used as a mouse: Go to previous 
page.
Press in to activate image correction for 
images that are wider at the top or bottom due 
to tilting the projector. Press the     keys to 
adjust the image.
Not recommended for spreadsheets or text 
displays to avoid text distortion.
Pg.DnZooms out (reduces) the image.
Remote used as a mouse: Go to next page.
PowerTurns projector power on and off.
ModeActivates the remote control as a mouse. The 
green LED indicator on the Mode button turns 
on indicating mouse active mode. Press again 
to turn off mouse mode. A USB cable must be 
connected to the projector for the mouse mode 
to work.
MenuPress to display the OSD menus. Press again 
to exit the OSD menus.
SourcePress to view the current video image. 
If you have multiple video sources connected, 
press again to select among the sources.
BlankHides image being displayed and displays a 
blank blue screen. Press again to resume 
display of the image. Typically used for a 
pause in a presentation.
AutoAutomatically adjusts the projected image to 
the optimum settings for the attached 
components.
NOTE:The infrared emitter is at the top of the remote control 
near the laser pointer. It has a range of 9m (29.5 feet). Do not 
block the infrared emitter. If the projector does not pick up the 
signals from the remote control, make sure the emitter and 
sensor on the projector are not blocked and that the emitter is 
within range. 
						

							Xerox DP1015 User’s Guide19
User Controls
Using the Remote Control as a Mouse
If a USB cable is connected to your computer and the projector, the 
remote control can be used in place of the computer’s mouse. This 
is especially helpful when giving a presentation in front of an 
audience so you can move the mouse cursor on the screen without 
having to be near the computer.
1. Press the Mode button on the remote control to switch it into 
mouse mode.
The LED indicator on the Mode button turns green indicating 
mouse mode is active.
2. The remote control can now be used as the mouse.
To de-activate the mouse mode, press the Mode button again.
Button Mouse Function
Freeze/Esc/LLeft mouse button.
Enter/RRight mouse button.
Pg.UpGo to previous page.
Pg.DnGo to next page.
ModeTurns on/off the remote control as a mouse.
Directional Selection 
Keys (     )Moves the mouse cursor. 
						

							User Controls
20Xerox DP1015 User’s Guide
On-Screen Display (OSD) Menus 
The On-Screen Display (OSD) menus provide the options to make 
image adjustments and change a variety of settings. 
Displaying Menus and Selecting Items
1. To open the OSD Menu, press the Menu button on the remote 
control or on the projector’s control panel.
To close the OSD Menu, press the Freeze/ESC/L button. The 
menus close if you don’t select from them within 10 seconds.
This example shows the Management menu selected from the 
OSD Main menu.
2. To select one of the menus on the OSD Main menu, press the 
  keys.
3. Press the   key or Enter/R button to get to the selected menu.
4. Press the     keys to highlight a control on the selected 
menu, then press the Enter/R button. In the example above, 
the OSD Location control is highlighted.
5. Press the     keys to adjust the highlighted control.
6. To accept your new setting, press the Menu button to return to 
the OSD Main menu.
7. When you’re finished changing settings, press the Menu button 
or the Freeze/ESC/L button. The OSD menu closes and your 
new settings are in effect.
NOTE:As you’re adjusting a control, you can return it to its 
previous setting by pressing the Auto button.
NOTE:The menus in this section show typical settings, but the 
actual settings you will see depend on the type of video signal.
OSD Main menuSelected menu (Management 
menu in this example) 
						

							Xerox DP1015 User’s Guide21
User Controls
Adjust the Projector Image
The Image menus are slightly different for Video Mode (the Video 
Adapter is attached to the projector) and VGA Mode (the Video 
Adapter is removed).
Image Menu (Video Mode)
Brightness—Lightens or darkens the image. The higher the 
number, the brighter the image.
You may need to readjust the Brightness after the projector warms 
up.
Contrast—Controls the degree of difference between the lightest 
and darkest parts of the image. Adjusting the contrast changes the 
amount of black and white in the image. The higher the number the 
greater the contrast.
Hue—Adjusts the balance between the red and green colors in the 
image. Increasing the Hue increases the amount of red in the 
image. Decreasing the Hue increases the amount of green in the 
image.
Saturation—Adjusts the image from black and white to fully 
saturated color. The higher the number, the greater the color 
saturation.
Sharpness—Adjusts the sharpness of the image. The higher the 
number the sharper the image. 
						

							User Controls
22Xerox DP1015 User’s Guide
Image Menu (VGA Mode)
[
Brightness—Lightens or darkens the image. The higher the 
number, the brighter the image.
You may need to readjust the Brightness after the projector warms 
up.
Contrast—Controls the degree of difference between the lightest 
and darkest parts of the image. Adjusting the contrast changes the 
amount of black and white in the image. The higher the number the 
greater the contrast.
Keystone—Adjusts image distortion caused by tilting the projector.
Do not change this setting when displaying text or spreadsheets. 
Changing the Keystone setting may distort the displayed text.
Zoom—Enlarges or reduces the image size. The higher the 
number the more the image is enlarged.
Sometimes when you zoom an image, you will then want to move it 
left or right to center it on the screen. To zoom the image and also 
move it:
1. With the Zoom control selected on the menu, press the 
Enter/R key.
Now the Pg.Up or Pg.Dn keys on the remote control will 
enlarge or reduce the image, and the     keys will move 
the image left or right
2. Press the Pg.Up or Pg.Dn keys on the remote control to 
enlarge or reduce the image.
3. Press the     keys to move the image left or right.
4. Press the Enter/R key again to return to the menu. 
						

							Xerox DP1015 User’s Guide23
User Controls
Adjust the Computer Display Image
The Display menus are slightly different for Video Mode (the Video 
Adapter is attached to the projector) and VGA Mode (the Video 
Adapter is removed).
Display Menu (Video Mode)
Keystone—Adjusts image distortion caused by tilting the projector.
Do not change this setting when displaying text or spreadsheets. 
Changing the Keystone setting may distort the displayed text.
Proportion—Switches the length-to-width aspect ratio between 
4:3 and 16:9. The correct proportion to select is based on the type 
of video source you are using. If the image seems to be distorted or 
stretched, change the proportion.
User Color—Select Ye s to adjust individual colors manually. The 
menu on the left appears. Select No to adjust the color 
temperature. The menu on the right, with the Color Temp control, 
appears.
User Red, User Green, User Blue—Adjust the amount of colors in 
the Display image.
Color Temp—Adjusts the color temperature range. Higher 
temperatures make the screen look colder, lower temperatures 
make the screen look warmer. The available color temperature 
range is between 6100K and 9300K. 
						

							User Controls
24Xerox DP1015 User’s Guide
Display Menu (VGA Mode)
Frequency—Changes the display data frequency to match the 
frequency of your computer’s graphics card. If vertical flickering 
lines appear on the image, adjust the frequency until they 
disappear.
Phase—Synchronizes the signal timing of the display with the 
timing of your computer’s graphics card. If the image flickers or is 
unstable, adjust the tracking until the image is stable.
V Position—Moves the image up and down on the screen.
H Position—Moves the image left and right on the screen.
Proportion—Switches the length-to-width aspect ratio between 
4:3 and 16:9. The correct proportion to select is based on the type 
of video source you are using. If the image seems to be distorted or 
stretched, change the proportion.
User Color—Select Ye s to adjust individual colors manually. The 
menu on the left appears. Select No to adjust the color 
temperature. The menu on the right, with the Color Temp control, 
appears.
User Red, User Green, User Blue—Adjust the amount of colors in 
the Display image.
Color Temp—Adjusts the color temperature range. Higher 
temperatures make the screen look colder, lower temperatures 
make the screen look warmer. The available color temperature 
range is between 6100K and 9300K. 
						

							Xerox DP1015 User’s Guide25
User Controls
Adjust the Audio
Vo l u m e—Adjusts the overall volume.
Treble—Adjusts the treble volume.
Bass—Adjusts the amount of medium and lower audio 
frequencies.
Mute—Mutes the audio.
Choose a Language
1. Use the     keys to select the language you want.
2. Press the Menu button.
The menus will be displayed in the selected language.