Xerox Phaser 750P User Manual

							30Phaser  750 Color Printer 
Guidelines for printing on labels:
nUse Tektronix Color Laser Labels.
nIf any of the labels on a sheet are missing, do not use that 
sheet; it may damage printer components.
nWhen selecting Tek Label as the media type, the printer 
requires that room temperature be cooler than 27 degrees C 
(81 degrees F). If the temperature is above this, the printer 
reports an error and stops printing.
 
Labels
Downloaded From ManualsPrinter.com Manuals 
						

							User Guide31
Automatic 2-Sided Printing
Caution
Never put media in the Duplex Unit; the printer reports a 
media jam.
Use only laser bond paper for automatic two-sided printing 
in the paper tray. Do not use any special media (glossy coated 
paper) to print automatic two-sided printing. Two-sided 
printing can be done manually; refer to Manual 2-Sided 
Printing From the Multi-Purpose Tray on page 35.
Automatic two-sided printing requires that the Lower Tray Assembly 
be installed.
1.Make sure that the Duplex Unit is inserted in the printerÕs upper 
(a) slot. 
2.Load 75 - 90 g/m
2 (20 - 24 lb.) paper in the paper tray.
If you are using pre-printed paper, such as letterhead:
a.Place the first side to be printed face-down.
a
b
c
LegalPaper
A/LetterPaper
DuplexPaper
0632-27
2-Sided Prints
Downloaded From ManualsPrinter.com Manuals 
						

							32Phaser  750 Color Printer 
b.Place the top of the page under the paper trayÕs hooks.
This example shows letterhead paper. 
3.Insert the paper tray in the printerÕs middle (b) or lower (c) tray 
slots.
Note
For best results with two-sided printing, use 90 g/m
2 (24 lb.) 
laser paper.
4.Decide on a binding preference (how the page turns) for Step 5: 
a.Long-Edge binding or uncheck Bind on top edge. 
PAPERA4
1234567
0632-28
a b
0632-29
2-sided Prints 
Downloaded From ManualsPrinter.com Manuals 
						

							User Guide33
b.Short-Edge binding or check Bind on top edge. 
5.In the Print screen, select the 2-Sided Printing option and a 
binding preference:
PC Drivers:
Windows 95 /  Windows 98
a.From the File menu, select Print.
b.Click Properties.
c.Click the Setup tab.
d.Click Print on 2-Sides option.
e.Check or uncheck Bind on top edge.
Windows NT4
a.Start/Settings/Printers.
b.Right-mouse-button-click on your printerÕs icon.
c.From the pop-up menu, select Document Defaults.
d.Click the Advanced tab.
e.Under Paper/Output, select Print on Both Sides.
f.Select Long Side or Short Side.
0632-30
 
Downloaded From ManualsPrinter.com Manuals 
						

							34Phaser  750 Color Printer 
Macintosh Drivers:
LaserWriter 8.6
a.From the File menu, select Print.
b.From the pull-down menu, choose Layout.
c.Select Print on Both Sides.
d.Select a binding preference. 
LaserWriter 8.3.4
a.From the File menu, select Print.
b.Click the Options button.
c.Select 2-Sided Printing.
d.Select Short-Edge Binding or Long-Edge Binding.
6.Send the job to the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							User Guide35
Manual 2-Sided Printing From the 
Multi-Purpose Tray
Side 1
Caution
Use only laser bond paper for the automatic two-sided 
printing in the paper trays. The Multi-Purpose tray should be 
used for manual two-sided printing on Tektronix Premium 
Color Printing Paper, Tektronix Glossy Coated Paper, or 
Heavy Paper. Two-sided printing on specialty media can 
shorten component life. For opacity and feed reliability, use 
laser paper that is 90 g/m
2 (24 lb. bond). For best results, do 
not use heavy toner coverage on Side 1 of a manual 2-Sided 
Print; also, increase the top margin on Side 1 to at least 
12mm (or .5  in.).
nFor a multi-page document, print odd-numbered pages for Side 1. 
(This selection is application-specific).
1.Set the media thickness switch; refer to page 17 for the correct 
setting.
Downloaded From ManualsPrinter.com Manuals 
						

							36Phaser  750 Color Printer 
2.Insert paper with the side to be printed face-up. 
This example shows letterhead paper. 
3.In the printerÕs front panel, select the media type and size at the 
prompt. 
4.In the Print screen (using a supported driver), select 
Multi-Purpose Tray as the Paper Source or Tray Selection. Send 
the job to the printer.
5.Remove the printed paper from the output tray.
Front Panel Media Type
Paper
nStandard laser paper, 75-105 g/m2 
(20-28 lb.)
Tektronix Glossy Coated 
Paper
nTektronix Glossy Coated Paper
Heavy Paper
nCard stock, 120 - 150 g/m2 (32 - 40 lb.)
nCover stock, 120 - 150 g/m2 (40 - 54 lb.)
nIndex stock, 120 - 150 g/m2 (60 - 80 lb.)
nHeavy laser paper, 120 - 150 g/m2 
(32 - 40 lb.)
32564-06
1234567
Downloaded From ManualsPrinter.com Manuals 
						

							User Guide37
Side 2
Note
For a multi-page document, print even-numbered pages for 
Side 2. (This selection is application-specific).
1.Insert the paper with the blank side face-up.  
2.In the printerÕs front panel, select the media type and size at the 
prompt. 
3.In the Print screen (using a supported driver), select 
Multi-Purpose Tray as the Paper Source or Tray Selection. Send 
the job to the printer.
4.Remove the printed paper from the output tray.
32564-07
1234567
Downloaded From ManualsPrinter.com Manuals 
						

							38Phaser  750 Color Printer 
Troubleshooting Print Quality
For detailed troubleshooting information, refer to the printerÕs 
CD-ROM or the Tektronix Color Printer Knowledge Base web site:
www2.tek.com/TekSMART/
If you notice a problem with the quality of your prints, the probable 
solution is replacing one of the supplies. Keep in mind this basic 
guideline:
nIf the symptom appears in a single color:
Replace the Toner Cartridge.
nIf the symptom appears in all colors:
Replace the Imaging Unit, or Fuser, or Fuser Roll, or 
Main Charge Grid, or Transfer Kit. 
To diagnose the problem, check these items:
1.Check the front panel for messages on replacing supplies.
Downloaded From ManualsPrinter.com Manuals 
						

							User Guide39
2.From the Help menu, scroll to Supplies Information, press OK 
and print the Supplies Page. Use it to diagnose and correct 
problems. The Supplies Page contains useful information, such as 
the remaining life for supplies. 
3.From the front panel Help menu, scroll to Print Quality, press 
Menu, scroll to Help Pages, press Menu, and print Diagnostic Test 
Pages. (This includes five color pages and one instruction page.) 
Examine the prints for symptoms.  
 Phaser® 750 COLOR PRINTERSupplies Usage
Toner Cartridges
}Toner Door
Fuser
& Fuser Roll Front Panel Display
Imaging Unit
& Main Charge Grid
Front Door
Toner
Imaging Unit
Main Charge Grid
Fuser Roll
Transfer Kit 
(located in paper feeder)
FuserReorder: 016-1662-00
110V Reorder: 016-1660-00
Reorder: 016-1664-00Reorder: 016-1665-00
Reorder: 016-1663-00
BlackPages Remaining: >500 @ 5% coverage
Standard Reorder: 016-1807-00CyanHi-Capacity Reorder: 016-1803-00
220V Reorder: 016-1661-00
HEX XXX
HEX XXX
HEX XXXHEX XXX
HEX XXX
Pages Remaining: >500 @ 5% coverage
Standard Reorder: 016-1804-00 Hi-Capacity Reorder: 016-1800-00MagentaPages Remaining: >500 @ 5% coverage
Standard Reorder: 016-1805-00YellowHi-Capacity Reorder: 016-1801-00Pages Remaining: >500 @ 5% coverage
Standard Reorder: 016-1806-00 Hi-Capacity Reorder: 016-1802-00
0% 50% 100% 32%Life RemainingSerial #:
Avg. Coverage/Image: 5.8%
Date Installed: Sep 1, 1999
0% 50% 100% %Life Remaining
0% 50% 100% 64%Life Remaining
0% 50% 100% %Life RemainingDate Installed:Date Installed:
tektronix.com/Color_Printers/
Serial #:
Avg. Toner Coverage/Page: 13.3%
Date Installed: Sep 1, 1999
0% 50% 100% %Life Remaining
lackPages Remaining: >500 @ 5% coverage
Standard Reorder: 0 Hi-Capacity Reorder: 0
agentaPages Remaining: >500 @ 5% coverage
Standard Reorder: 0 Hi-Capacity Reorder: 0
0% 50% 100%
 32%Life Remaining
Serial #:
Avg. Coverage/Image: 5.8%
Date Installed: Sep 1, 1999
0% 50% 100% 72%
Life Remaining
Serial #:
Avg. Toner Coverage/Page: 13.3%
Date Installed: Sep 1, 1999
0632-56
0632-60
Test Print 
Black
Cyan
Magenta
Yellow
Print Quality
Downloaded From ManualsPrinter.com Manuals