Xerox Phaser 7400DXF User Manual

							Printing on Specialty Media
Phaser® 7400 Color Printer
3-42 4.When the control panel prompts you to confirm the type and size of paper in the tray, 
select Change setup, and then press the OKbutton.
a.Select Labels as the paper type, and then press the OKbutton.
Note:If you are printing on unusually heavy labels, select Heavy Labels. For more 
information, see Supported Paper and Media on page 3-3.
b.Select either Letter SEF or A4 SEF, and then press the OKbutton.
5.In the printer driver, select Tray 1 as the paper source and/or select Labels as the paper 
type.
Printing Glossy Paper
Glossy paper within the weight range 120–160 g/m2 can be printed from Tray 1 (MPT). It 
should be printed on one side only.
To order paper, transparencies, or other specialty media, contact your local reseller or go to 
www.xerox.com/office/supplies
.
Guidelines
■Do not open sealed packages of glossy paper until you are ready to load them into the 
printer.
■Leave glossy paper in the original wrapper, and leave the packages in the shipping carton 
until ready to use.
■Remove all other paper from the tray before loading glossy paper.
■Load only the amount of glossy paper you are planning to use. Do not leave glossy paper 
in the tray when you are finished printing. Reinsert unused glossy paper in the original 
wrapper and seal. 
■Rotate stock frequently. Long periods of storage in extreme conditions can cause glossy 
paper to curl and jam the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Printing on Specialty Media
Phaser® 7400 Color Printer
3-43
Printing Glossy Paper from Tray 1 (MPT)
1.Open Tray 1 (MPT) by pulling up and out on the handle, and then unfold the two 
extensions.
7400-094
1
2
3
Downloaded From ManualsPrinter.com Manuals 
						

							Printing on Specialty Media
Phaser® 7400 Color Printer
3-44 2.Insert the paper into the tray, and adjust the paper guides to fit the paper:
■Place the side to be printed faceup, with the long edge against the roller, and the top of 
the page towards the back of the printer.
■Do not load more than 50 sheets.
3.When the control panel prompts you to confirm the type and size of paper in the tray, 
select Change setup, and then press the OKbutton.
a.Select Glossy Paper as the paper type, and then press the OKbutton.
b.Select the appropriate size, and then press the OKbutton.
4.In the printer driver, select Tray 1 as the paper source and/or select Glossy Paper as the 
paper type.
7400-218
Downloaded From ManualsPrinter.com Manuals 
						

							
Printing on Specialty Media
Phaser® 7400 Color Printer 3-45
Printing Custom Size Paper
In addition to the wide variety of standard paper sizes that you can use for printing, you can 
also print on custom size paper  within the following dimensions.
■Banner size paper, paper that is more than 457 mm (18 in.) long, must be printed from 
Tray1(MPT). 
■Custom size envelopes must be printed from Tray 1 (MPT).
Printing Custom Size Paper from Tray 1 (MPT)
1.Open Tray 1 (MPT)  by pulling up and out on the ha ndle, and then unfold the two 
extensions.
Tray 1 (MPT) Tray 2
Width 100–320 mm (3.95–12.60 in.) 100–328 mm (3.95–12.90 in.)
Height 90–1219 mm (3.55–48.00 in.) 148–457 mm (5.85–18.00 in.) 
7400-094
1
2
3
Downloaded From ManualsPrinter.com Manuals 
						

							
Printing on Specialty Media
Phaser® 7400 Color Printer 3-46
2.
Insert the paper into Tray 1 (MPT), and adjust  the paper guides to fit against the sheets.
■The paper can be loaded with either the long  or short edge entering first, as shown in 
the following illustrations. 
■The maximum paper width (W) is 320 mm (12.60 in.). 
■The maximum paper height (H) is 1219 mm (48.00 in.).
Long-Edge Feed
■For  single-sided  printing , place the side 
to be printed  faceup, with the top of the 
page towards the back of the printer.
■For  2-sided  printing , place side one 
facedown , with the top of the page 
towards the back of the printer. Short-Edge Feed
■For 
single-sided  printing , place the side 
to be printed  faceup, so the top of the 
page enters first.
■For  2-sided  printing , place side one 
facedown , so the top of the page enters 
first.
Note: For more information about automatic 
2-sided printing, see  Automatic 2-Sided 
Printing Guidelines  on page 3-29.
XEROX
7400-156
W
H
XEROX
7400-157
W
H
Downloaded From ManualsPrinter.com Manuals 
						

							Printing on Specialty Media
Phaser® 7400 Color Printer
3-47 1.If you loaded paper or media with a height less than 111 mm (4.4 in.), open the left-side 
output tray.
2.When the control panel prompts you to confirm the type and size of paper in the tray, 
select Change setup, and then press the OKbutton.
3.Select the appropriate paper type, and then press the OKbutton.
4.If the correct custom size appears in the menu, select it, and then press the OKbutton. If 
you are using a new custom size, set the custom width and custom height:
a.Select New Custom Size, and then press the OKbutton.
b.Use the Up Arrow and Down Arrow buttons to select the value for the custom width, 
and then press the OKbutton.
c.Use the Up Arrow and Down Arrow buttons to select the value for the custom height, 
and then press the OKbutton.
5.When you submit your print job, either set the document size in the application to the 
custom size, or select Tray 1 as the paper source in the printer driver.
1
2 3
7400-012
1
2 3
7400-012
Downloaded From ManualsPrinter.com Manuals 
						

							Printing on Specialty Media
Phaser® 7400 Color Printer
3-48
Printing Custom Size Paper from Tray 2
1.Pull out the tray.
2.If necessary, adjust the length and side paper guides to fit the paper size.
Note:When the paper guides are adjusted correctly, there may be a small space between 
the paper and the guides.
7400-017
7400-018
Downloaded From ManualsPrinter.com Manuals 
						

							Printing on Specialty Media
Phaser® 7400 Color Printer
3-49 3.Insert the paper into Tray 2:
■The paper can be loaded with either the long or short edge on the right side of the tray, 
as shown in the illustrations. 
■The maximum paper width (W) is 328 mm (12.90 in.). 
■The maximum paper height (H) 457 mm (18.00 in.).
1.At the control panel, select Paper Tray Setup, and then press the OKbutton.
a.Select Tr a y 2 P a p e r, and then press the OKbutton.
b.Select Change setup, and then press the OKbutton.
c.Select the appropriate paper type, and then press the OKbutton.
2.If the correct custom size appears in the menu, select it, and then press the OKbutton. 
Otherwise: 
a.Select New Custom Size, and then press the OKbutton.
b.Use the Up Arrow and Down Arrow buttons to select the value for the custom width, 
and then press the OKbutton.
c.Use the Up Arrow and Down Arrow buttons to select the value for the custom height, 
and then press the OKbutton.
3.When you submit your print job, either set the document size in the application to the 
custom size, or select Tray 2 as the paper source in the printer driver.
Long-Edge Feed
■For single-sided printing, place the 
side to be printed facedown, with the 
top of the page at the back of the tray.
■For 2-sided printing, place side one 
faceup, with the top of the page at the 
back of the tray. Short-Edge Feed
■For single-sided printing, place the side to 
be printed facedown, with the top of the 
page on the right side of the tray.
■For 2-sided printing, place side one 
faceup, with the top of the page on the right 
side of the tray.
Note:For more information about automatic 
2-sided printing, see Automatic 2-Sided 
Printing Guidelines on page 3-29.
W
H
W
H
Downloaded From ManualsPrinter.com Manuals 
						

							Choosing Output Options
Phaser® 7400 Color Printer
3-50
Choosing Output Options
This section includes:
■Output Tray Guidelines on page 3-50
■Offsetting Output on page 3-52
■Stapling Output on page 3-53
■Using the Hole Puncher on page 3-54
Output Tray Guidelines
The printer has an output tray on top of the printer and an output tray on the left side of the 
printer. If your printer has a finisher installed, you can send output to the finisher to be 
punched and/or stapled. Use the following guidelines to choose which output tray to use for 
your print jobs:
Top Output Tray (Factory default)
■Use for all paper and media types.
■Use for paper and media sizes with heights 
111 mm (4.4 in.) or more.
■Delivers output facedown.Left-Side Output Tray
■Use for paper and media sizes with heights less 
than 111 mm (4.4 in.).
■Delivers output faceup.
■Use to reduce curling of heavy paper or specialty 
media.
■Open the left-side output tray before selecting it 
from the printer driver.
7400-028
XEROX
7400-029
Downloaded From ManualsPrinter.com Manuals 
						

							
Choosing Output Options
Phaser® 7400 Color Printer 3-51
Selecting an Output Tray from the Printer Driver
To select an output tray  for a specific print job:
See also:  Stapling Output  on page 3-53
Using the Hole Puncher  on page 3-54
Finisher Output Tray (Optional)
■Use for paper and other media within the following dimensions:
Width: 305 mm (12 in.) or less
Height: 125 mm (4.9 in.) or more
■Delivers paper less than 457 mm (18 in). long facedown; delivers longer paper, 
card stock, and specialty media faceup.
Operating System Steps
Windows98SE, 
Windows Me, 
Windows 2000, 
Windows XP, 
Windows Server 
2003, or 
Windows NT 4.x 1.
Select the  Output Options  tab.
2. Select the ouput tray from the  Paper Destination drop-down list.
Mac OS 9 or 
Mac OS X, version 
10.2 and higher 1.
In the  Print dialog box , select  Finishing Options  from the drop-down 
list.
2. Select the output tray from the  Paper Destination drop-down list.
7400-030
XEROX
Downloaded From ManualsPrinter.com Manuals