Home > Xerox > Scanner > Xerox Documate 6440 User Guide

Xerox Documate 6440 User Guide

Here you can view all the pages of manual Xerox Documate 6440 User Guide. The Xerox manuals for Scanner are available online for free. You can easily download all the documents as PDF.

Page 11

Xerox® DocuMate® 6440Welcome
6User Guide
• Universal Serial Bus (USB) port
•Microsoft
® Windows® operating system: 
– 32-bit Windows XP (Service Pack 3)
– 32-bit or 64-bit Windows Vista (Service Pack 2)
– 32-bit or 64-bit Windows 7 (Service Pack 1)
– 32-bit or 64-bit Windows 8 / 8.1
– 32-bit or 64-bit Windows 10
• 2 gigabyte (GB) internal memory (RAM)
• Minimum available hard disk space:
– 350 MB for the scanner driver
– 750 MB for Visioneer OneTouch
– 1 to 2 GB for each additional application
Please...

Page 12

WelcomeXerox® DocuMate® 6440
User Guide7
The Xerox® DocuMate® 6440 Scanner 
Fe a t u r e s
1.Input Tray—Holds the documents in the Automatic Document Feeder for scanning. 
–Extension—Pull out to support various document lengths.
–Paper Guide Switch—Push up to allow the paper guides to adjust wider for dot matrix 
printer paper.
–Paper Guides—Slide to adjust to document width.
2.Automatic Document Feeder—Feeds documents through the scanner during scanning. 
–ADF Cover Release—Press to open the Automatic...

Page 13

Xerox® DocuMate® 6440Welcome
8User Guide
–Power Jack—Connect the power cord to the scanner. 

Page 14

User Guide9
Scanner Setup
1. Remove the scanner from its protective foam and plastic bag.
2. Remove any shipping tape from the scanner as indicated in the following illustration(s). 
The above illustrations are for example purposes only. Your scanner’s packaging may vary slightly.
3. Lift the input tray up from the scanner. Pull the output tray down from the scanner body. 
Remove any shipping tape from the input and output trays.
The above illustrations are for example purposes only. Your scanner’s...

Page 15

Xerox® DocuMate® 6440 Scanner Setup
10User Guide
4. Open the automatic document feeder cover and remove any tape or protective foam from 
inside the feeder. Close the feeder cover when you are finished.
The above illustrations are for example purposes only. Your scanner’s packaging may vary slightly.
5. Slide the release switch in the output tray if you want it to lay flat on the desk. 
Connect the Power Cord
Note: Only use the power supply (DA-48M24 made by APD) included with your scanner. 
Connecting...

Page 16

Scanner Setup Xerox® DocuMate® 6440
User Guide11
Moving or Repacking the Scanner
If you want to move or repack the scanner, please follow the instructions in this section to prevent 
damage to the scanner’s input and output tray.
1. Lower the paper stop.
2. Close the input and output tray extensions.
3. Lift the output tray up and fold it against the scanner. Press on the output tray until it clicks in 
place.
4. Flip the paper guides closed so that they are flat against the input tray. 

Page 17

Xerox® DocuMate® 6440 Scanner Setup
12User Guide
5. Close the input tray.
Safety Lock
Your scanner may have a slot for installing a Kensington® style safety lock. This slot can be 
identified by the lock icon. It is to the left of the USB port on the scanner. When following the 
instructions in this document, make sure you connect the USB cable into the USB port which is 
identified by the USB symbol. 
A lock is not provided with the scanner and this document does not contain instructions on 
purchasing...

Page 18

User Guide13
Installation
Please make sure of the following before you begin installation:
• If you are prompted to reboot during installation, please select “No”. Finish installing the rest 
of the software, then close all open windows and reboot your computer. 
• The information in this guide may cover software not provided with the scanner you 
purchased. Please disregard any information about the software not applicable to your 
scanner.
• If your computer has AntiVirus or AntiSpyware software...

Page 19

Xerox® DocuMate® 6440 Installation
14User Guide
Install the Software and Connect the 
Scanner
1. Start Microsoft Windows and make sure that no other applications are running.
2. Insert the installation disc into your computer’s DVD-ROM drive.
The disc automatically starts.
3. The Select Language window opens. Click the drop-down menu arrow and select the 
language to use. Click OK.
The disc’s Main menu window opens.
Note: If the disc does not start, check the following:
– Make sure the disc drives door...

Page 20

Installation Xerox® DocuMate® 6440
User Guide15
4. On the Main menu, select Install software.
5. Make sure the boxes for Scanner Driver and Visioneer OneTouch are selected, as well as any 
other applications you want to install.
Note: The software provided with your scanner may differ slightly from the list shown in the 
window.
6. Click Install now. 
Start reading Xerox Documate 6440 User Guide

Related Manuals for Xerox Documate 6440 User Guide

All Xerox manuals