Wolf Cinema Projector Dcx 1500fd User Manual

2-6
VeRTICal anD hoRIzonTal PosITIon
The correct vertical and horizontal position of the projector in relation to the screen depends on 
the lens type and the screen size. Ideally, the projector should be positioned perpendicular to the 
screen. This way, the image will appear rectangular instead of keystoned (trapezoidal)\
. 
The  vertical position of the image can be offset – that is moved above or below the optical axis 
(lens center) by adjusting the fully motorized lens mount with the keypad. The...

2-7
Figure 2.1 Vertical Offset Examples
Section	2	►	Installation	and	Setup
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View 

2-8
Figure 2.2 Lens Vertical Offsets
Section	2	►	Installation	and	Setup
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View 

2-9
The  horizontal  position  of  the  image  can  be  offset  –  that  is  moved  to  the  left  or  right  of  lens 
center, by adjusting the fully motorized lens mount through software. The amount of horizontal 
offset available depends on the lens installed and if the image has already been vertically offset. 
Horizontal  offset  can  also  be  expressed  as  the  percent  of  half  the  image  width  –  the  number 
of pixels of shift to one side of lens center. Refer to Figure 2.3 for some...

2-10
Figure 2.4 Lens Horizontal Offset Examples
Section	2	►	Installation	and	Setup
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View
Iso - Rear Left ViewIso - Front Right View
Rear View
Top View
Side - Left ViewSide - Right View 

2-11
MoUnTIng
There  are  several  methods  for  mounting  the  projector.  Depending  on  your  chosen  installation, 
one method may be more suitable than another. In typical front and rear screen installations the 
projector can be mounted to a secure and level surface, such as a table.\
CeIlIng MoUnT — The projector can also be inverted and suspended from the ceiling using 
a	 specially	 designed	 ceiling	mount	fixture.	 This	type	 of	mounting	 is	recommended	 for	fixed	
installations and for those...

2-12
Sources connect to the Input Panel located at the back of the projector. See Figure 2.6.
The upper right corner (INPUT 1) typically accepts an RGB signal from an external analog RGB 
source, or it can also be used for YPbPr signals or additional video sources. Just beside these 
BNCs, the DVI-I connector  (INPUT 2) accepts digital or analog display signals from a computer. 
Connect analog composite video at  INPUT 3 or S-Video at INPUT 4 from devices such as VCRs, 
laser disc players or DVD...

2-13
Figure 2.7 Connecting RGB and Sync 
noTes: 1) If for some reason the projector fails to recognize a signal as an RGB signal, specify 
this Color Space option within the Picture Adjustments menu. See 3.5 Adjusting the Image.  2) To 
connect YPbPr signals–such as from DVDs or analog HDTV sources–to INPUT 1, use the red, 
green and blue BNCs as described in YPbPr Signals (below).
Connect a YPbPr signal (component video) to  InPUT 1 or InPUT 2 as shown in Figure 2.8.
noTes: 1) If, for some reason, the...

2-14
DVI Digital Video
InPUT  3  and InPUT  4  provide  simultaneous  connection  of  both  a  composite  video  source 
(InPUT 3) and an S-Video source ( InPUT 4). See Figure 2.9. 
Use  the  DVI-I  connector  at  InPUT  2  to  connect  either  analog  or  digital  video  devices  to  the 
projector. When connecting devices that transmit an analog video signal such as VCRs, laptops, 
and PCs use the DVI cable provided with the projector. Plug the   DVI-I (single link) connector 
end to the projector and...

2-15
As  an  alternative  to  the  projector’s  keypad  or  remote,  you  may  wish  to  communicate  with  the 
projector using a PC or other controller. Such a device sends commands and receives feedback 
via  serial  links  (RS232  and  RS422),  Ethernet  or  GPIO  communications  to  the  projector,  all 
described below.
As desired, direct the projector’s IR remote keypad towards the display screen or the projector’s 
IR  sensors. Alternatively,  connect  a  wired  (tethered)  version  of  the...