Wolf Cinema Projector Dcx 1000i User Manual

3-58
4. seT  blenD WIDTh: On one projector, increase the  Blend Width for an overlapping edge 
(for  example,  if  the  projector’s  image  is  on  left,  its  right  edge  overlaps  the  adjacent  image 
— adjust  Right Blend Width). Use the same setting on the second projector for this shared 
edge.
5.  Re-adjust  width  (both  projectors)  until  the  overly  bright  band  at  the  midpoint  of  the 
overlapping blends disappears or just changes to very light gray. For the shared edge, use 
the same...

3-59
Section	3	►	Operation
4. Use the following three color slide bars, Black Red Level, Black Green Level and Black Blue 
Level, so the black hue of each projector matches.
5.  You can choose which of the next four options, Top, Bottom, Left, Right, to use depending on 
which edge of the projector you are working with has been edge blended. The blend width 
can be adjusted to line up properly but by default it corresponds to the edge blending setting 
determined for that edge. 
 
6.  The brightness and...

3-60
Occasionally the projector will encounter an error condition that can interrupt normal operation. 
Such  a  condition  can  be  caused  by  a  simple  invalid  keypad  entry,  an  input  signal  error  (most 
common)	or	a	system	 error.	The	manner	 in	which	 users	are	to	be	 notified	 of	error	 conditions	 is	
set in the Menu Preferences menu:
To see error messages displayed on-screen, select the “
•	 screen” or “all” option (recommended 
by Wolf Cinema).
To	be	notified	via	a	serial	communication...

3-61
When  the  projector  encounters  a  system  malfunction,  either  a  System  Warning  message  or  a 
System Error message may appear. Both types of messages are accompanied by a numerical 
error code on the status LED display. A system malfunction can be cleared with 
Exit Exit from 
presentation	level,	but	may	indicate	the	need	for	service	by	a	qualified	service	technician.
noTe:  System  messages  appear  on-screen  only  if  Display  Error  Messages  has  been  set  to 
“Screen” or “All”....

3-62
Code Description
GENERAL
12  Software bug. Contact dealer/factory.
13  CRC	error	in	flash	ROM.	Download	new	software.
14  Engineering-only programming is complete. Call Wolf Cinema, replace TIPM.
15  Attempting to download code without being in boot mode
16  Invalid interrupt. Power off/on. If it persists, contact dealer/factory.
17  User forced system to stay in boot mode
18  Jumper for programming boot not installed LAMP FAILURES
20  Lamp turned on unexpectedly (fault related to ballast)
21  Lamp...

4-1
The  projector  is  an  international  regulatory  agency  approved  product  designed  for  safe  and 
reliable  operation.  To  assure  complete  safety  at  all  times  it  is  important  to  acknowledge  the 
following precautions while operating the projector.
 WaRnIng  
always power down the projector using appropriate procedure and disconnec\
t  all power sources before cleaning or servicing.
 WaRnIng  
always remove the lens when shipping the projector.
 W aRnIng  
neVeR look directly into...

4-2
Section	4	►	Maintenance
Lamp: The projector uses a Cermax® Xenon lamp to deliver its high brightness. A lamp should 
be  replaced  when  it  has  reached  its  end  of  life  or  if  a  noticeable  change  in  brightness  occurs. 
Keep  track  of  the  number  of  hours  the  lamp  has  been  in  use  (Lamp  Menu)  and  be  aware  of 
any  changes  to  brightness. These  indicators  will  help  you  effectively  maintain  operation  of  the 
projector. 
 WaRnIng  
Wait approximately five minutes...

4-3
Slots  and  vents  in  the  projector  provide  ventilation.  Never  block  or  cover  these  openings. This 
ensures reliable operation of the projector and prevents overheating. Do not place the projector over a radiator or heat register. The projector should not be placed 
•	
in an enclosure unless proper ventilation is provided.
Do not insert objects into the ventilation openings of the projector. They may touch dangerous 
•	
voltages	 or	short-out	 components	 resulting	in	a	fire	 or	shock...

4-4
Part 
Description  Frequency 
Action
Lens As required 
Clean the lens only when absolutely necessary. 
A small amount of dust on the lens has very little 
effect on picture quality.
To clean:  Use	a	soft	 microfiber	 cloth	without	 any	
chemicals. Use only a high-quality coated optics 
cleaning	 fluid,	which	 can	be	purchased	 from	
most  camera  supply  stores.  Apply  the  coated 
optics	 fluid	directly	 onto	the	microfiber	 cloth	
until moistened. Wipe in a single sweep across 
the surface of the...

4-5
The  IR  Remote  Keypad  uses  two  AA  size,  1.5V  batteries  (preferably  alkaline).  To  install  new 
batteries: Open the battery compartment at the backside of the keypad by placing your thumb in the 
1. 
oval  depression  and  sliding  the  cover  out  about  ½  inch.  See  Figure  4.1.  Remove  the  old 
batteries and properly discard. Wait a minute or two.
Place the new batteries in the compartment, orienting the positive/negative of each battery 
2. 
according  to  the  labels  in  the...