Whirlpool Awod 9561 Programme Chart Manual

							GB PROGRAMME CHART
5019 301 06044
Whirlpool is a registered trademark of Whirlpool USA
❉: optional / Yes : dosing required1)
For improved garment care, spin speed is restricted in these programmes.
The wool and handwash cycles of this machine have been tested and approved by The Woolmark Company 
for the washing of Woolmark garments labelled as “machine wash” or “hand wash” provided that the garments 
are washed according to the instructions on the garment label and those issued in this programme chart. 
M0512
Programme
Care
Labels
Max 
Load
kg
Type of wash/Notes
- For temperature selection, respect the manufacturer’s 
recommendations on the care label
Detergents and additives
Special options
Max
Spin
Speed
rpm
Pre-
wash
Main 
Wa s h
Softener
Eco
Pre-
wash
Start
delay
Easy
ironing
Intensive
rinse
Rinse
hold
Va r i a b l e
spin
Eco
Pré-
lavage
Départ
différé
Anti
froissage
Rinçage
plus
Arrêt
cuve
pleine
Essorage
variable
White Cotton /
Antibacterial
 Coton7.0
Normally to heavily soiled bed linen, table linen and underwear, towels, 
shirts etc. made of cotton and linen.
At a temperature of 80°C or more, this programme eliminates 
bacteria, ensuring sanitization of your laundry. The bacteria removal 
efficiency has been tested following a similar methodology to the NF 
EN 13697 standard of Nov. 2001.
❉
Ye s
❉❉❉❉ ❉ ❉❉ ❉
max.
Cotton
Coton7.0
 
6.0
Synthetics
Synthétique
 
 
2.5
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, 
Trevira), polyamide (Perlon, Nylon) or blends with cotton.
❉
Ye s
❉❉❉❉ ❉ ❉❉ ❉
1000
1)
Daily load
 
3.0
Slightly to normally soiled textiles made of cotton and/or synthetics.
—
Ye s
❉——
❉❉ ❉❉❉
max.
Quick wash
Chrono3.0
Shortly worn outer clothing made of cotton, polyester, polyamide and 
blends with cotton.
—
Ye s
❉——
❉——
❉❉
max.
Delicates
Délicat
 
1.5
Curtains and delicate clothing, dresses skirts, shirts and blouses.
❉
Ye s
❉—
❉❉——
❉❉
1000
1)
Wool
Laine1.0
Only woollens, labelled with the Woolmark and identified as machine 
washable. 
This programme (40°C) is tested and approved by The Woolmark 
Company for machine washable wool.
—
Ye s
❉——
❉——
❉❉
1000
1)
Handwash
Lavage main/1.0
Textiles made of silk, linen, wool and viscose marked as 
“handwashable”. 
This programme (40°C) is tested and approved by The Woolmark 
Company for handwashable wool.
—
Ye s
❉——
❉——
❉❉
400
1)
Rinse & Spin
Rinçage & Essorage
—
7.0
Same as the last rinse and the final spin in the “Cotton” programme.
——
❉——
❉—
❉❉ ❉
max.
Spin
Essorage
—
7.0
In this programme spinning is intensive. Same as the spin cycle in the 
“Cotton” programme.
—— — ——
❉———
❉
max.
Gentle Spin
Essorage doux
—
1.0
In this programme spinning is gentle. Same as the spin cycle in the “Wool” 
programme.
—— — ——
❉———
❉
1000
1)
Drain
Vidange
—
—
Drain only - no spinning. Alternative method of terminating programme 
after “Rinse Hold”.
—— — ——— — — — —
—
A. “Door open” indication
This washing machine is equipped with 
automatic safety functions which 
detect and diagnose faults at an early 
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
E. Programme selector
F. “Start/Pause” button
G. “Variable spin” button
H. Programme sequence indicator
I. “Reset” button
J. “Start delay” button
K. “Temperature” button
L. Display
D
HC
F
I
EA
J
B
K
G
L
30106044GB.fm  Page 1  Thursday, May 3, 2007  10:22 AM
Black process 45.0° 100.0 LPI 
 
						

							5019 301 06044
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as 
described in the chapter “Detergent and Additives” 
in your Instructions for Use.
1. Turn the 
programme selector to the desired 
programme. The display shows the programme 
duration in hours and minutes as well as the 
predefined temperature. The 
“Start/Pause” 
button flashes.
2. The 
temperature can be altered by pressing 
the “Temperature” button.
3. The indication lamp of the predefined 
spin speed 
lights up; in case you want to set another spin 
speed, press the “Variable spin” button.
Push the button(s) of any option(s) desired - the 
respective indication lights up.
When the combination of programme and additional 
option(s) is not possible, the indication lights switch off 
automatically. Unsuitable combinations of options are 
deselected automatically.
“Eco” button
 With a modified temperature profile and a slightly 
prolonged washing duration, the optimum 
combination of excellent washing result and even 
lower energy consumption is achieved.
“Prewash” button
 Only for heavily soiled loads (for example sand, 
granular dirt) sensible. Increases the cycle time 
by approximately 15 min. Do not use liquid detergent for the main wash 
when activating the Prewash option.
“Easy ironing” button
 Can be used together with “Cotton”, 
“Synthetics” and “Daily load” programmes to 
make ironing easier.
 Increases the water quantity and the clothes are 
spun very gently.
“Intensive rinse” button
 More water is added and rinse cycle is prolonged.
 This option is particularly suitable for areas with 
very soft water, washing baby linen and helps 
people with allergies.
“Rinse hold” button
 The laundry remains in the last rinse water 
without progressing to the final spin cycle to avoid 
creasing and prevent colours from changing.
 This option is particularly recommended for the 
programmes “Synthetics”, “Daily load” and 
“Delicates”.
 It is particularly useful if you want to postpone 
spinning to a later time, or if you want to drain only.
 If you select “Rinse hold”, do not leave the laundry 
to soak for too long.
Note: The programme stops to “Rinse hold” at 
the time the “Anticrease” light in the programme 
sequence indicator is on. The indication lamp 
next to the 
“Start/Pause” button flashes.
Terminate the “Rinse hold” option:
 Press the 
“Start/Pause” button; the 
programme will terminate automatically with the 
final spin cycle for the present wash programme.CONSUMPTION DATA
Programme
Temperature 
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
*
White Cotton / Antibacterial 95 7.0 59
**1.90 2:00
Cotton 60 7.0 56 1.14 2:10
Cotton with “Eco”
***60 7.0 51 1.02 2:20
Cotton 40 6.0 56 0.70 2:00
Synthetics 60 2.5 50
**0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
Delicates 30 1.5 60 0.50 0:45
Wool 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home 
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*The time indicated on the display can deviate from the values in the table, because it takes into account the household 
conditions applicable at that time.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***Reference Programme for Energy Label.ADD DETERGENTS, CLOSE THE DOOR 
AND SELECT THE PROGRAMMESELECT ANY DESIRED OPTION
 If you do not wish to spin the clothes, turn the 
programme selector knob to the “Drain” programme 
and press the 
“Start/Pause” button. 
“ Variable spin” button 
 Every programme has a predefined spin speed.
 Press the button to set another spin speed.
 If spin speed “0” is selected, the final spinning is 
cancelled but intermediate spin peaks remain 
during rinse. The water is drained out only.
The “Start Delay” allows to run the machine at the 
consumer’s convenience, for example at night when 
electricity is cheaper. Do not use liquid detergent 
when activating the “Start Delay”.
 Select programme, temperature and options.
 Press the “Start Delay ” button to select the delay 
time by 1 to 23 hours;
 Press the 
“Start/Pause” button. 
The indication light next to the “Start Delay ” 
button lights up and the countdown of the delay 
time begins. The dot between hours and 
minutes of the delay time indicated flashes.
The time delay indication disappears when the 
programme starts and it is replaced by the 
remaining programme time.
 Once having pressed the 
“Start/Pause” button, 
the number of hours preselected can be reduced 
by pressing and holding the “Start Delay ” 
button. From 1 hour on, the delay time can also 
be reduced in steps of 10 minutes.
To cancel the “Start Delay ”
..before you press the “Start/Pause” button:
 Turn the programme selector to another 
position or press the 
“Reset” button.
..after having pressed the “Start/Pause” button:
 Press the “Reset” button for at least 3 seconds - the 
start delay time disappears from the display.
Open the tap and press the 
“Start/Pause” button. 
The indication lamp next to the 
“Start/Pause” button 
lights up. The programme sequence indicator shows 
the current programme phase, running from left to 
right through Wash, Rinse, Spin/Drain.
The display shows the remaining programme time. 
Due to variations in load and temperature of inlet 
water, the remaining time is newly calculated in certain 
programme phases. If this is the case, 
an animation 
appears on the display.Before starting and after end of a programme, the 
lamp lights to show that the door can be opened. As 
long as a wash programme is running, the door 
remains locked and must on no account be forced 
open. In case you have an urgent need to open it 
during a running programme, refer to “Cancel 
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by 
a fault in an electrical component. Refer to the 
“Troubleshooting Guide” in your Instructions for Use; if 
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. 
Open the water tap; if the indication still lights up, 
refer to the “Troubleshooting Guide” in the 
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the 
drain hose is kinked or the filter must be cleaned; in 
the latter case refer to the Instructions for Use 
(“Removing the Filter”).
 All the lights of the programme sequence 
indicator are off, and the “Door open” 
indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the 
“Start/Pause” button to pause the 
programme. The light flashes.
2. Select the new programme, temperature, any 
options and another spin speed if you want.
3. Press the 
“Start/Pause” button again. The new 
programme continues at the same position 
where the previous programme was interrupted. 
Do not add detergent for this programme.
The 
“Reset” button cancels a programme before 
the end.
 Press the 
“Reset” button for at least 3 
seconds. Any existing water is drained out 
before the door can be opened.START DELAYPROGRAMME START
“DOOR OPEN” INDICATIONRED INDICATIONSPROGRAMME ENDCHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME STARTCANCEL (RESET) A RUNNING 
PROGRAMME BEFORE THE END
30106044GB.fm  Page 2  Thursday, May 3, 2007  10:22 AM
Black process 45.0° 100.0 LPI