Whirlpool Awod 53205 Programme Chart Manual

							
GB
5019 301 01109
Programme
Care LabelsMax.Load
kg
Type of wash / Notes
- respect the manufacturer's recommendations on the care label
Detergents and AdditivesSpecial optionsMaxSpin Speed
rpm
Pre- washMain 
WashSoftenerStartdelayEco Pre-washEasyironingIntensiverinseRinseholdVariablespin
Cotton/ Antibacterial  95 °C
40-60-95 °C5.0Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and linen.Selecting “Cotton 95°, this programme eliminates bacteria, ensuring sanitization of your 
laundry. The bacterial removal efficiency has been tested following a similar methodology to 
the NF EN 13697 standard of Nov. 2001
YesMax.Cotton 40 - 60 °C
Jeans40 °C40 °C5.0Normally soiled cotton jeanswear and garments made of jeanslike material such as trousers and jackets.Yes––Max.
Synthetics30 - 40 - 60 °C30-40-60 °C2.5Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, T
revira), 
polyamide (Perlon, Nylon) or blends with cotton. Yes1000 1)
Delicates30 - 40 °C30 - 40 °C1.5Curtains and delicate clothing, dresses, skirts, shirts and blouses.Yes–––1000 1)
Daily load40 °C40 °C3.0Slightly to normally soiled textiles made of cotton and/or synthetics.–
Yes––Max.
Quick wash30 °C30 °C3.0Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton.– Yes––––Max.
Wool
Cold - 40 °C       - 40 °C1.0Only woollens labelled with the woolmark and identified as machine washable.
This programme (40°) is tested and approved by The Woolmark Company for machine 
washable wool.– Yes––––1000 1)
Handwash40 °C40 °C1.0Textiles made of linen, silk, wool and viscose marked as “handwashable”.
This programme (40°) is tested and approved by The Woolmark Company for hand-washable wool.–
Yes––––400 1)
Lingerie30 °C30 °C1.0This programme is particurarly suitable to treat delicate lingerie (use of laundry net strongly recommended).–Yes––––400 1)
Rinse & Spin–5.0Same as the last rinse and the final spin in the “Cotton” programme.–– –––Max.
Spin–5.0In this programme spinning is intensive. Same as the spin cycle in the “Cotton ” programme.––––––––Max.
Drain––Drain only - no spinning. Alternative method of terminating programme after “Rinse hold”.––––––––––
A.  “Door open” indication
This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage 
and react appropriately, e.g.:
B.  “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
Whirlpool is a registered trademark of Whirlpool USA.
E.  Programme selector
F.  “Start/Pause” button
G. Spin speed selector
H. Programme sequence indicator
I.  “Reset” button
J.  “Start delay ” button
K.  Time display
 : option / Yes : dosing required1) For improved garment care spin speed is restricted in these programmes.
PROGRAMME CHART
The wool and handwash cycles of this machnes have been tested and approved by The W oolmark Company for the 
washing of Woolmark garments labeled as “machine wash” or “hand wash” provided that the garments are washed 
according to  the instructions on the garment label and those issued in this programme chart.M0512
A
B
H
F
E
G
C
D
J
I
K
 
						

							
5019 301 01109
ProgrammeTemperature(°C)
Load
(kg)Water(l)
Energy
(kWh)Approx. ProgrammeDuration(hours : minutes)*
Cotton / Antibacterial955.049**1.902:00
Cotton 605.0440.952:10
Cotton with “Eco”***605.0440.852:20
Cotton405.0440.602:00
Jeans405.0600.602:10
Synthetics602.550**0.701:30
Synthetics402.5450.551:15
Delicates301.5500.500:45
Daily load403.0450.451:00
Quick wash303.0400.400:30
Wool
401.0550.600:45
Handwash401.0450.600:40
Lingerie301.0450.500:36
CONSUMPTION DATA
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*  The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions
  applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.***  Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to show the the door can be opened. As long as a wash programme is running, the door remains locked and must on no account  be forced  open. In case you have an urgent need to open it 
during a running programme, refer to “Cancel (Reset) 
a running programme before the end”.
RED INDICATIONS
“Service”Lighting up of the “Service” indication can be caused 
by a fault in an electrical component. Refer to the 
“Troubleshooting Guide” in your “Instructions for 
Use”; if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. 
Open the water tap: if the indications still lights 
up, refer to the “Troubleshooting Guide” in the 
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the 
drain hose is kinked or the filter must be cleaned: in the latter case refer to the Instructions for Use 
(“Removing the Filter”).
Push the button(s) of any option(s) desired - the respective indication lamp lights up.When the combination of programme and additional option(s) is not possible, the indication lights switch 
off automatically. Unsuitable combinations of options 
are deselected automatically.
“Eco” button•  With modified temperature profile and a slightly
  prologned washing duration, the optimum
  combination of excellent washing result and even
  lower energy consumption is achieved.
“Prewash”
 button•  Only for heavily soiled loads (for example sand,
  granular dirt) sensible. Increases the cycle time by
  approximately 15 min.
Whirlpool is a registered trademark of Whirlpool USA.
PROGRAMME START
Open the tap and press the  “Start/Pause” button. The indication lamp next to the  “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from 
left to right through Wash, Rinse, Spin/Drain.
The time display shows the remaining programme time. Due to variations in load and temperature of 
inlet water, the remaining time is newly calculated 
in certain programme phases. If this is the case, an 
animation appears on the time display.
PROGRAMME END
•  All the lights of the programme sequence indicator
  are off, and the “Door open” indication lights up.
1.  Turn the programme selector to the “Off/O”
  position.
2.  Close the water tap.
3.  Open the door and unload the machine.
4.  Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME START
1.  Press the “Start/Pause” button to pause the
  programme. The light blinks.
2.  Select the new programme (with temperature), 
  any options and another spin speed if you want.
3.  Press the  “Start/Pause” 
button again. The new
  programme continues at the same position where
  the previous programme was interrupted. Do not
  add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END
• Do not use liquid detergent for the main wash 
  when activating the “Prewash” option.
“Easy ironing” button•  Can be used together with “Cotton”, “Synthetics”
  and “Daily load” programmes to make ironing 
  easier.
•  Increases the water quantity and the clothes are 
  spun very gently.
“Intensive rinse” button•  More water is added and rinse cycle is prolonged.•  This option is particularly suitable for areas with 
  very  soft water, washing baby linen and helps 
  people with allergies.
“Rinse hold” button•  The laundry remains in the last rinse water 
  without pregressing to the final spin cycle to avoid 
  creasing and prevent colours from changing.
•  This option is particularly recommended for the
  programmes “Synthetics”, “Daily load” and
  “Delicates”.
•  It is particularly useful if you want to postpone
  spinning to a later time, or if you want to drain 
  only.
•  If you select “Rinse hold” do not leave items to 
  soak for too long.
 Note: The programme stops to “Rinse hold” at 
  the time the “Rinse hold” lights in the programme  
  sequence indication is on. The indication lamp 
  next to the  “Start/Pause”
 button blinks.
START DELAY
Add detergents as indicated on the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use.
1.  Turn the programme selector to the desired
  programme and temperature.
2.  The 
time display shows the duration of the 
  chosen programme (in hours and minutes), and 
  the “Start/Pause
” indication lamp is blinking.
3.  The indication lamp of the predefined spin speed
  lights up. Terminate the “Rinse hold” option:
•  Press the 
“Start/Pause” button; the programme
  will terminate automatically with the final spin 
  cycle   for the present wash programme.
•  If you do not wish to spin the clothes, turn the
  programme selector knob to the “Drain” 
  programme and press the  “Start/Pause”
 button.
“ Variable spin”
 button•  Every programme has a predefined spin speed.•  Press the button to set another spin speed.•  If spin speed “0” is selected, the final spinning is
  cancelled but intermediate spin peaks remain 
  during rinse. The water is drained out only.
The  “Reset” button cancels a programme before the end.•  Press the  “Reset” button for at least 3 seconds.
  Any existing water is drained out before the door 
  can be opened.
The “Start delay ” allows to run the machine at the 
consumer’s convenience, for example at night when 
electricity is cheaper.  
Do not use liquid detergent 
when activating “Start delay ” option.
•  Select programme, temperature and options.•  Press the “Start delay ” button to select the delay
  time by 1 to 23 hours.
•  Press the  “Start/Pause” button.
  The countdown of the delay time begins; the 
  “Start delay ” indication lamp and the dot on the 
  display will keep blinking until the programme 
  starts.
•  The time delay indication disappears when the
  programme starts and it is replaced by the 
  remaining programme time.
•  Once having pressed the  “Start/Pause” button, 
  the number of hours preselected can be reduced 
  by pressing again the “Start delay ” button.
To cancel the “Start delay ”
...before you press the  “Start/Pause” button:•  Turn the programme selector to another position 
  or press the “Reset” button....after having pressed the  “Start/Pause” button:•  Press the “Reset” button for at least 3 seconds 
  - the start delay time disappears from the time 
  display
.