Whirlpool Awod 5120 Programme Chart Manual

							5019 301 01226
Programme
Care LabelsMax.Load
kg
Type of wash / Notes
- respect the manufacturer's recommendations on the care label
Detergents and AdditivesSpecial optionsMaxSpin Speed
rpm
Pre- washMain WashSoftenerPre-washRapidStartdelayClean+ColdwashIntensiverinseEasyironingRinseholdSpin
Cotton / Antibacterial 95 °C5.0Normally to heavily soiled and robust white cotton laundry. In case of heavy soiling or stains, you can add an oxygenbased bleach additive which can \
be used at 95°C. This programme eliminates bacteria, ensuring sanitization of your laundr\
y. iYesii–ii–iiiiMax.
Cotton 40 - 60 °C5.0Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and linen.iYesiiiiiiiiiiMax.
Jeans40 °C5.0Normally soiled cotton jeanswear and garments made of jeanslike material\
 such as trousers and jackets.iYesiiiiii––iiMax.
Synthetics30 - 40 - 60 °C2.5Normally soiled garments made of artificial fibres (like polyester, polyacryl, viscose etc.) or their blends with cotton.iYesiiii–iiiiiMax.
Delicates30 - 40 °C1.5Curtains and delicate clothing, dresses, skirts, shirts and blouses.iYesii–i–i––ii1000 1)
Daily load40 °C3.0Slightly to normally soiled robust laundry made of cotton, linen, artifi\
cial fibres and their blends. Effective one-hour programme. Make sure to wash only similar colours together in one wash load.–Yesi––i–iiiiiMax.
Quick wash30 °C3.0Shortly worn clothing made of cotton, polyester, polyamide and blends with cotton. Brief programme to refresh your laundry.–Yesi––i–i––iiMax.
WoolCold        - 40 °C1.0Only woollens, labelled with the Woolmark and identified as machine washable. This programme (40°C) is tested and approved by The Woolmark Company for machine washable wool.–Yesi––i–i––ii1000 1)
Handwash40 °C1.0Textiles made of silk, linen, wool and viscose marked as “handwashable”. This programme (40°C) is tested and approved by The Woolmark Company for handwashable wool.–Yesi––i–i––ii400 1)
Lingerie30 °C1.0This programme is particurarly suitable to treat delicate lingerie (use\
 of laundry net strongly recommended).–Yesi––i–i––ii400 1)
Rinse & Spin–5.0Same as the last rinse and the final spin in the “Cotton” programme.––i––i ––i–iiMax.
Spin–5.0Intensive spin. Same as the spin cycle in the “Cotton” programme.–––––i–––––iMax.
Drain––Drain only - no spinning. Alternative method of terminating programme af\
ter “Rinse hold”.–––––i–––––––
Whirlpool is a registered trademark of Whirlpool USA.
i : option / Yes : dosing required1) For improved garment care spin speed is restricted  in these programmes.
GB                   PROGRAMME CHART
A
B
H
FEG
C
D
J
I
K
The wool and handwash cycles of this machnes have been tested and approv\
ed by The Woolmark Company for the washing of Woolmark garments labeled as “machine wash” or “hand wash” pr\
ovided that the garments are washed according to  the instructions on the garment label and those issued in this programme cha\
rt.              M0612
E. Programme selectorF.  “Start/Pause” buttonG. Spin speed selectorH. Programme sequence indicatorI. “Reset” buttonJ. “Start delay ” buttonK. Time display
Acustic noise level :Washing   -    59 dB(A) / 1 pWSpinning  - 1400 rpm  77 dB(A) / 1 pW - 1200 rpm  75 dB(A) / 1 pW
A. “Door open” indication
This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
  
						

							5019 301 01226
CONSUMPTION DATA
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to show the the door can be opened. As long as a wash programme is running, the door remains locked and must on no account  be forced  open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”.
Whirlpool is a registered trademark of Whirlpool USA.
PROGRAMME START
Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain.The time display shows the remaining programme time. Due to variations in load and temperature of inlet water, the remaining time is newly calculated in certain programme phases. If this is the case, an animation appears on the time display.
PROGRAMME END
• All the lights of the programme sequence indicator  are off, and the “Door open” indication lights up.1. Turn the programme selector to the “Off/O” position.2. Close the water tap.3. Open the door and unload the machine.4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the programme. The light blinks.2. Select the new programme (with temperature), any options and another spin speed if you want.3. Press the “Start/Pause” button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END
START DELAY
Add detergents as indicated on the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use.1. Turn the programme selector to the desired programme and temperature.2. The time display shows the duration of the chosen programme (in hours and minutes), and the “Start/ Pause” indication lamp is blinking.3. The indication lamp of the predefined spin speed lights up.
The “Reset” button cancels a programme before the end.• Press the “Reset” button for at least 3 seconds.  Any existing water is drained out before the door can  be opened.
The “Start delay ” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper.  Do not use liquid detergent when activating “Start delay ” option.•	 Select	programme,	temperature	and	options.•	 Press	the	“Start	delay ”	button	to	select	the	delay time by 1 to 23 hours.•	 Press	the	“Start/Pause” button. The countdown of the delay time begins; the “Start  delay ” indication lamp and the dot on the display will    keep blinking until the programme starts.•	 The	time	delay	indication	disappears	when	the programme starts and it is replaced by the remaining programme time.•	 Once	having	pressed	the	“Start/Pause” button, the number of hours preselected can be reduced by pressing again the “Start delay ” button.To cancel the “Start delay ”...before you press the “Start/Pause” button:•	 Turn	the	programme	selector	to	another	position	or press the “Reset” button....after having pressed the “Start/Pause” button:•	 Press	the	“Reset” button for at least 3 seconds - the start delay time disappears from the time display.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the “Troubleshooting Guide” in your Instructions for Use.
“Service”Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your “Instructions for Use”; if the fault persists, contact our After Sales Service.
“Water tap closed”The appliance has no or insufficient water supply. Open the water tap: if the indications still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use.
“Clean pump”Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned: in the latter case refer to the Instructions for Use (“Removing the Filter”).
Consumption values were measured in normalized conditions in compliance \
with standard IEC/EN 60 456. Consumption data in the home may vary with \
respect to the values in the table in relation to the water supply press\
ure and temperature, the load and the type of wash.Water and energy consumption refer to the default setting of the programmes; selecting special options or m\
odifying spin speed or temperature will change the consumption data.  The programme duration may differ from the values indicated above as it \
depends on the operation conditions applicable at that time (see also “Troubleshooting Guide” in your Instructions for Use).*  To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.**  Reference Programmes for Energy Label.*** Automatic adaption of programme duration after detection of wash load.
ProgrammeTemperature
(°C)
Load
(kg)
Water
(l)
Energywithout “Rapid”(kWh)
Approx. Programme Duration      (hrs : min)
without “Rapid”with “Rapid”
Cotton/Antibacterial955.053*1.702:00–Cotton**605.0440.754:002:30Cotton**602.5320.652:20***Cotton405.0490.602:451:45Cotton**402.5320.552:30***Jeans405.0650.633:002:00Synthetics602.550*0.701:301:09Synthetics402.5450.501:150:54Delicates301.5500.500:45–Daily load403.0450.451:00–Quick wash303.0400.400:30–Wool401.0550.600:45–Handwash401.0450.600:40–Lingerie301.0450.500:36–
Push the button(s) of any option(s) desired - the respe-ctive indication lamp lights up.When the combination of programme and additional op-tion(s) is not possible, the indication lights switch off au-tomatically. Unsuitable combinations of options are de-selected automatically.
“Prewash” button•	 Only	for	heavily	soiled	loads	(for	example	sand, granular dirt) sensible. Increases the cycle time by approximately 15 min.•	 Do	not	use	liquid	detergent	for	the	main	wash	when	 activating the “Prewash” option.
“Rapid” button•		 Enables	quicker	washing	by	shortening	the programme duration.•		 Recommendable	for	small	loads	or	only	lightly	soiled laundry.
“Clean+” button•	 Choose	this	option	if	you	use	an	in-wash	additive	for stain removal (powder, for example “Vanish”) - it will optimize the additive’s efficiency to get better wash performance and stain removal.
•		 Selectable 	for 	programmes 	“Cotton”, 	“Synthetics”  and Jeans; choose temperature of 30 or 40°C and use  with maximum load.•		 Add	an	appropriate	amount	of	in-wash	additive	for	 stain removal (powder) to the main wash chamber,  together with your detergent (only use powder  detergent with this option).  Respect the manufacturer’s dosing instructions.•		 Prolongs	the	programme	by	approx.	10	to	15	 minutes.•		 Appropriate	for	use	of	stain	removers	and	bleaches	 on oxygen basis. Chlorine or perborate bleaches  must not be used!
“Cold wash” button•	 Water	is	heated	only	up	to	20ºC.•	 Suitable	for	delicate	laundry	items	with	wash	 temperature	recommendation	of	max.	30ºC	on	the care label.•	Selectable only on the lowest temperature step  of each programme.
“Intensive rinse” button•	 More	water	is	added	and	rinse	cycle	 is	prolonged.•	 This	option	is	particularly	suitable	for 	areas	with	very soft water, washing baby linen and helps people with allergies.
“Easy ironing” button•	 Can	be	used	together	with	“Cotton”,	“Synthetics” and “Daily load” programmes to make ironing easier.•	 Increases	the	water	quantity	and	the	 clothes	are	spun very gently.
“Rinse hold” button•	 The	laundry	remains	in	the	last	rinse	 water	without pregressing to the final spin cycle to avoid creasing and prevent colours from changing.•	 This	option	is	particularly	recommended	for	the programmes “Synthetics”, “Daily load” and “Delicates”.
•	 It	is	particularly	useful	if	you	want	to	postpone spinning to a later time, or if you want to drain only.•	 If	you	select	“Rinse	hold”	do	not	leave	items	to	soak	 for too long. Note: The programme stops to “Rinse hold” at the time the “Rinse hold” lights in the preogramme sequence indication is on. The indication lamp next to the “Start (Pause)” button blinks.
Terminate the “Rinse hold” option:• Press the “Start (Pause)” button; the programme  will terminate automatically with the final spin cycle for the present wash programme.• If you do not wish to spin the clothes, turn the  programme selector knob to the “Drain” programme and press the “Start (Pause)” button.
“Spin” button• Every programme has a predefined spin speed.• Press the button to set another spin speed.• If spin speed “0” is selected, the final spinning is  cancelled but intermediate spin peaks remain during rinse. The water is drained out only.