Whirlpool Awod 43115 Programme Chart Manual

							GB AWO/D 43115 PROGRAMME CHART❉: optional / Yes : dosing required1)
For improved garment care, spin speed is restricted to 400 rpm in this programme.
2)
Cold wash option is selectable only for the lowest temperature step of the programme.
5019 301 10258/A
Whirlpool is a registered trademark of Whirlpool USA
Programme
Care
Labels
Type of wash/Notes
- for temperature selection, respect the manufacturer’s recommendations on the care label
Max 
Load
kg
Detergents and additives
Special options
Max
Spin
Speed
rpm
Pre-
wash
Main 
Wa s h
Softener
Pre-
wash
Cold
wash
Easy
ironing
Va r i a b l e
spin
Cotton
40 - 60 - 95 °C
40 - 60 - 95 °C
 
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made 
of cotton and linen. 
With heavily soiled laundry the additional “Prewash” option can be selected as well.5.0
❉
Ye s
❉❉
❉
2)
❉❉
1000
Synthetics
30 - 40 - 60 °C
30 - 40 - 60 °C
 
 
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), 
polyamide (Perlon, Nylon) or blends with cotton.2.5
❉
Ye s
❉❉
❉
2)
❉❉
1000
Delicates30 - 40 °C
30 - 40 °C
 
Curtains and delicate clothing, dresses skirts, shirts and blouses. 1.5
❉
Ye s
❉❉❉
—
❉
1000
Daily load
40 °C
40 °C
 
Slightly to normally soiled textiles made of cotton and/or synthetics. 3.0 — Yes
❉
—
❉❉ ❉
1000
Quick wash
30 °C
30 °C
Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton. 3.0 — Yes
❉
—
❉
—
❉
1000
WoolCold - 40 °C
 - 40 °C
Only woollens with a felt-free finish, labelled with the woolmark and identified as machine 
washable.1.0 — Yes
❉
—
❉
—
❉
1000
Handwash
40 °C
40 °C
Textiles made of linen, silk, wool and viscose marked as “handwashable”. 1.0 — Yes
❉
—
——
❉
400
1)
Lingerie30 °C
30 °C
This cycle is particularly suitable to treat delicate lingerie (use of a laundry net strongly 
recommended).1.0 — Yes
❉
—
❉
—
❉
400
1)
Rinse & Spin
—Same as the last rinse and the final spin in the “Cotton” programme.
5.0 — —
❉
—— —
❉
1000
Spin
—In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme.
5.0 — — — — — —
❉
1000
Gentle Spin
—In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme.
1.0 — — — — — —
❉
1000
Drain
—
Water is drained only without any spinning.
—— — — —— — — —
A. “Door open” indication
This washing machine is equipped with 
automatic safety functions which 
detect and diagnose faults at an early 
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
E. Programme selector
F. “Start/Pause” button
G. Spin speed selector
H. Programme sequence indicator
I. “Reset” button
D
HC
F
I
G E
BA
 
						

							5019 301 10258/A
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as 
described in your Instructions for Use. Close the door 
and turn the 
programme selector to the desired 
programme and temperature. The indication lamp 
next to the 
“Start/Pause” button   flashes.
Push the button(s) of any option(s) desired - the 
respective indication lamp lights up.
When the combination of programme and additional 
option(s) is not possible, the indication lights switch 
off automatically. Unsuitable combinations of options 
are deselected automatically.
“Prewash” button
 Only for heavily soiled loads (for example sand, 
granular dirt) sensible. Increases the cycle time 
by approximately 15 min.“Cold wash” button
 Water is heated only up to 20°C
 Suitable for delicate laundry items with wash 
temperature recommendation of max. 30° on 
the care label.
 Selectable only on the lowest temperature step 
of each programme.
“Easy ironing” button
 Can be used together with “Cotton” , 
“Synthetics”   and “Daily load”   
programmes to make ironing easier.
 Increases the water quantity and the clothes are 
spun very gently.
“ Variable spin” button
 Every programme has a predefined spin speed.
 Press the button to set another spin speed.
 If spin speed “0” is selected, the final spinning is 
cancelled but intermediate spin peaks remain 
during rinse. The water is drained out only.CONSUMPTION DATA
Programme
Temperature 
(°C)
Load
(kg)
Wa t e r
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
*
Cotton 95 5.0 49
**1.90 2:00
Cotton
***60 5.0 44 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Synthetics 60 2.5 50
**0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Lingerie 30 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption 
data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, 
the load and the type of wash.
*The remaining time indicator can deviate from the values in the table, because it takes into account the household 
conditions applicable at that time.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains 
the water out.
***Reference Programme for Energy Label.ADD DETERGENTS, CLOSE THE DOOR 
AND SELECT THE PROGRAMMESELECT ANY DESIRED OPTION
Open the tap and press the 
“Start/Pause” button . 
The indication lamp next to the 
“Start/Pause” button 
 lights up. The programme sequence indicator 
shows the current programme phase, running from left 
to right through Wash, Rinse, Spin/Drain.
 When the programme phase is finished, the 
corresponding indication goes out.
Before starting and after end of a programme, the 
lamp lights to show that the door can be opened. As 
long as a wash programme is running, the door 
remains locked and must on no account be forced 
open. In case you have an urgent need to open it 
during a running programme, refer to “Cancel 
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by 
a fault in an electrical component. Refer to the 
“Troubleshooting Guide” in your Instructions for Use; 
if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. 
Open the water tap; if the indication still lights up, 
refer to the “Troubleshooting Guide” in the 
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the 
drain hose is kinked or the filter must be cleaned; in 
the latter case refer to the Instructions for Use 
(“Removing the Filter”). All the lights of the programme sequence 
indicator are off, and the “Door open” 
indication  lights up.
1. Turn the programme selector to the “Off/O” 
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the 
“Start/Pause” button   to pause 
the programme. The light flashes.
2. Select the new programme (with temperature), 
any options and another spin speed if you want.
3. Press the 
“Start/Pause” button   again. The 
new programme continues at the same position 
where the previous programme was interrupted. 
Do not add detergent for this programme.
The 
“Reset” button   cancels a programme 
before the end.
Press the 
“Reset” button   for at least 3 
seconds. Any existing water is drained out 
before the door can be opened.PROGRAMME START“DOOR OPEN” INDICATIONRED INDICATIONS
PROGRAMME ENDCHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME STARTCANCEL (RESET) A RUNNING 
PROGRAMME BEFORE THE END