Whirlpool Awod 062 Programme Chart Manual

							GB AWO/D 062
5019 301 01005
ProgrammeCareLabels
Max.Load
kg
Type of wash / Notes
- for temperature selection, respect the manufacturer's recommendations on the care label
Detergents and AdditivesSpecial optionsMaxSpin Speed
rpm
Pre- washMain WashSoftenerStartdelay 3)EcoPre-washIntensiverinseRinseholdVariablespin
Cotton60 - 95 °C
40 - 60 - 95 °C
6.0Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and linen.With heavily soiled laundry the additional “Prewash” option can be selected as well.iYes 2)iiiiiii1200Cotton40 °C5.0
Synthetics30 - 40 - 60 °C30 - 40 - 60 °C2.5Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or blends with cotton.iYes 2)iiiiiii1000 1)
Delicates30 - 40 °C30 - 40 °C1.5Curtains and delicate clothing, dresses, skirts, shirts and blouses.iYes 2)ii–i–ii1000 1)
Daily load40 °C40 °C3.0Slightly to normally soiled textiles made of cotton and/or synthetics.–Yesii––iii1200
Quick wash30 °C30 °C3.0Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton.–Yesii–––ii1200
WoolCold - 40 °C        - 40 °C1.0Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable.–Yesii–––ii1000 1)
Handwash30 - 40 °C30 - 40 °C1.0Textiles made of linen, silk, wool and viscose marked as “handwashable”.–Yesii–––ii400 1)
Rinse & Spin–6.0Same as the last rinse and the final spin in the “Cotton” programme.––ii––iii1200
Spin–6.0In this programme spinning is intensive. Same as the spin cycle in the “Cotton ” programme.–––i––––i1200
Gentle Spin–1.0In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme.–––i––––i1000 1)
Drain––Drain only - no spinning. Alternative method of terminating programme after “Rinse hold”.––––––––––
A. “Door open” indication
This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
Whirlpool is a registered trademark of Whirlpool USA.
E. Programme selector
F. “Start/Pause” button
G. Spin speed selector
H. Programme sequence indicator
 and Start delay indicators
I. “Reset” button
J. “Start delay ” button
AB
i :  option / Yes : dosing required1)   For improved garment care, spin speed is restricted in these programmes.2)   Do not use liquid detergents for the main wash when activating the prewash option.3)   Do not use liquid detergents when activating the Start delay.
PROGRAMME CHART
H
FEG
CD
J
I
 
						

							5019 301 01005
ProgrammeTemperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. ProgrammeDuration(hours : minutes)
Cotton956.059*1.902:00
Cotton606.0491.142:10
Cotton with “Eco”**606.0491.022:20
Cotton405.0560.702:00
Synthetics602.550*0.801:35
Synthetics402.5460.501:20
Delicates301.5600.500:45
Daily load403.0410.501:00
Quick wash303.0410.400:30
Wool401.0600.500:45
Handwash401.0450.500:40
Handwash301.0450.400:40
Add detergents as indicated on the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use.Close the door and turn the programme selector to the desired programme and temperature. The indication lamp next to the “Start/Pause” button flashes.
CONSUMPTION DATA
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to show the the door can be opened. As long as a wash programme is running, the door remains locked and must on no account  be forced  open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”.
RED INDICATIONS
“Service”Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your “Instructions for Use”; if the fault persists, contact our After Sales Service.
“Water tap closed”The appliance has no or insufficient water supply. Open the water tap: if the indications still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use.
“Clean pump”Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned: in the latter case refer to the Instructions for Use (“Removing the Filter”).
Push the button(s) of any option(s) desired - the respective indication lamp lights up.When the combination of programme and additional option(s) is not possible, the indication lights switch off automatically. Unsuitable combinations of options are deselected automatically.“Eco” button• With modified temperature profile and a slightly prologned washing duration, the optimum combination of excellent washingresult and even lower energy consumption is achieved.“Prewash” button• Only for heavily soiled loads (for example sand, granular dirt) sensible. Increases the cycle time by approximately 15 min.• Do not use liquid detergent for the main wash when activating the Prewash option.
Whirlpool is a registered trademark of Whirlpool USA.
PROGRAMME START
Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain.When the programme phrase is finised, the corresponding indication goes out.
PROGRAMME END
• All the lights of the programme sequence indicator are off, and the “Door open” indication lights up.1. Turn the programme selector to the “Off/O” position.2. Close the water tap.3. Open the door and unload the machine.4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the programme. The light flashes.2. Select the new programme (with temperature), any options and another spin speed if you want.3. Press the “Start/Pause” button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END
The “Reset” button cancels a programme before the end.
• Press the “Reset” button for at least 3 seconds. Any existing water is drained out before the door can be opened.
“Intensive rinse” button• More water is added and rinse cycle is prolonged.• This option is particularly suitable for areas with very soft water, washing baby linen and helps people with allergies.“Rinse hold” button• The laundry remains in the last rinse water without pregressing to the final spin cycle to avoid creasing and prevent colours from changing.• This option is particularly recommended for the programmes “Synthetics”, “Daily load” and “Delicates”.• It is particularly useful if you want to postpone spinning to a later time, or if you want to drain only. Note: The programme stops to “Rinse hold” at the time the “Rinse hold” lights in the preogramme sequence indication is on. The indication lamp next to the “Start/Pause” button flashes.Terminate the “Rinse hold” option:• Press the “Start/Pause” button; the programme will terminate automatically with the final spin cycle for the present wash programme.• If you do not wish to spin the clothes, turn the programme selector knob to the “Drain” programme and press the “Start/Pause” button.“ Variable spin” button• Every programme has a predefined spin speed.• Press the button to set another spin speed.
The “Start delay ” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper.• Select programme, temperature and options.• Press the “Start delay ” button to select the delay time by 1, 3, 6, 9 or 12 hours.• Press the “Start/Pause” button. The indication neto to the “Start delay ” button lights up and goes off when the programme starts.• Once having pressed the “Start/Pause” button, the countdown of the time delay begins. When the programme starts, the start delay indicator lights goes off and is replaced by the programme sequence indications.• After the “Start/Pause button has been pressed, the number of hours preselected can be reduced by pressing again the “Start delay ” button.To cancel the “Start delay ”..before you press the “Start/Pause” button:• Turn the programme selector to another position or press the “Reset” button...after having pressed the “Start/Pause” button:• Press the “Reset” button for at least 3 second - the start delay indicator light goes out.
START DELAY
• Press the button to set another spin speed.• If spin speed “0” is selected, the final spinning is cancelled but intermediate spin peaks remain during rinse. The water is drained out only.